similar to: 4.2 unstable kernel restarting before booting OS kernel

Hi all, I just upgraded my Debian/Etch with Xen3.3 machine to Debian/Squeeze Xen4.0 and now have problems with starting the Dom0 kernel. I always get the error message: Kernel panic not syncing: the kernel parameter noapic is incompatible with xen. My grub.cfg is: menuentry ''Debian GNU/Linux, with Linux 2.6.32-5-xen-686 and XEN 4.0-i386'' --cl$ insmod part_msdos

Hello, I compiled xen on ubuntu, but at the bot i got the kernel panic message. I enabled the support to ext4 fs. This is kernel panic error: EXT3-fs: unable to read superblock ETX4-fs (md0): unable to read superblock FAT: unable to read boot vector Kernel panic - not syncing: VFS: Unable to read superblock(9,8) My grub.cfg generated by update-grup: menuentry ''Ubuntu, with Linux

hi guys, It''s my first time here and in a mailing lists, I only participated in forums before. Please, If I make a mistake you should advise me. Let''s go! I was reading "xencommons not start" in a Remus Forum in order to install Remus. Well… I followed the tutorial < http://remusha.wikidot.com/configuring-and-installing-remus>, I reboot in xen_unstable and I had

hi guys, It''s my first time here and in a mailing lists, I only participated in forums before. Please, If I make a mistake you should advise me. Let''s go! I was reading "xencommons not start" in a Remus Forum in order to install Remus. Well… I followed the tutorial < http://remusha.wikidot.com/configuring-and-installing-remus>, I reboot in xen_unstable and I had

Hello, I have installed the Xen 4.1.1 and a working kernel 2.6.32.43 which supports Xen on a Ubuntu Linux 10.04 LTS. However, I have never successfully booted the Hypervisor and Dom0. The screen is always black after some kernel messages rapidly go by. I think that I may pass the wrong parameters to the kernel or Hypervisor with GRUB2. Can any one share his/her working grub.cfg for GRUB2 with

Confirmed this issue. To reproduce: Install a fresh Wheezy AMD64 guest under Xen 4.1 (hypervirtualized, boot from the debian-7.1.0-amd64-CD-1.iso). Use "entire disk" automatic layout for partitioning, this creates /dev/xvda1 for / and /dev/xvda5 for swap. It will create /boot/grub/grub.cfg with many references to (/dev/xvda,msdos1) which works fine when the machine is booted

Hi there, I''ve been trying to find out why my X server is not working with xen and my ati radeon driver, this is what I''ve got uname -a Linux netwarrior 3.2.4-debian #1 SMP Sun Mar 11 22:50:18 ART 2012 x86_64 GNU/Linux xorg.conf Driver "fglrx" grub config menuentry ''Debian GNU/Linux, with Linux 3.2.4 Debian'' --class debian --class gnu-linux

Hi. I''m trying to run Xen 4.0.1 with Debian Squeeze in Dom0 My grub config: menuentry ''Debian GNU/Linux, with Linux 2.6.32-5-xen-amd64 and XEN 4.0-amd64'' --class debian --class gnu-linux --class gnu --class os --class xen { insmod part_msdos insmod ext2 set root=''(hd0,msdos1)'' search --no-floppy --fs-uuid --set e719719a-35aa-4ada-8ab5-9b6c676bc89e

Hello Xen folks, I use Debian Squeeze. I want to passthrough PCI devices. With the old stable Debian (grub legacy) i did not have problems. I edit /etc/default/grub like: quote: GRUB_CMDLINE_XEN_DEFAULT="quiet xen-pciback.permissive xen-pciback.hide=(00:14.2)(01:05.1)" I run "update-grub". Now i look at /boot/grub/grub.cfg: ### BEGIN /etc/grub.d/20_linux_xen

Hi, I am using Xen 4.2.3 installed on an Intel Atom with a Debian Dom0 and 3 Debian domU''s installed. I am trying to run some benchmarks using the Arinc653 scheduler. I have edited my grub options to boot with ''maxcpus=1 sched=arinc653'' options. I can boot the dom0 and verify that the scheduler is enabled. However when I xl create, the VM is created but I cannot

Hi, we´ve got a bad problem here. We installed a new server with debian squeeze sw-raid and lvm. We´ve installed the the actual xen-linux-system-2.6.32-5-xen-amd64? system with grub2 but get an XEN BUG. We´ve tried alot, tested grub-legacy version but cannot get the XEN kernel to boot up. The XEN BUG occurs a  second after grub boots the kernel and there are no outputs at the serial console with

I have a couple Debian 6 HVM VMs. From what I''ve read, Debian 6''s standard kernels have pv_ops already enabled. I''d like to convert these to pv for the following reasons (Assuming both of are valid expectations): 1) so the VMs use pv for the NICs 2) so the VMs properly respond to shutdown/reboot commands from xm I''m having trouble converting them. I believe

Hi, I have installed Debian Buster with encrypted LVM so apon installation my root partition is encrypted. So far so good but as soon as I encrypt the boot partition, after reboot the OS won't start. If I start the drive directly with qemu, it works but it looks like Libvirt is somehow not able to deel with it. What am I missing? -- John Doe

Hello list, Using the mainline 3.5-rc6 kernel and yesterday''s xen-unstable, I''m having trouble passing in some PCI devices. Everything else works smoothly. Attached are some of the relevant logs and configurations. I did notice from the qemu logs that all the problematic devices have "IRQ type = INTx" whereas those that are working have "IRQ type =

You get these if you install Debian Wheezy as HVM and then try to convert to PV. This is Debian bug #603391. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Tested-by: Tril <tril@metapipe.net> --- tools/pygrub/examples/debian-wheezy-hvm.grub2 | 104 +++++++++++++++++++++++++ tools/pygrub/src/GrubConf.py | 6 +- 2 files changed, 109 insertions(+), 1

Package: xen-utils-4.0 Version: 4.0.1-1 Severity: normal Tags: patch pygrub could not boot a newly-updated Debian/testing domU with a non-chained grub2. The traceback was: Using <class 'grub.GrubConf.Grub2ConfigFile'> to parse /grub/grub.cfg WARNING:root:Unknown directive load_video WARNING:root:Unknown directive terminal_output Traceback (most recent call last): File

hi folks, anyone around who knows how to setup grub2 to allow at boot time a static memory allocation for the Domain-0. I use debain squeeze, lates update''s and my actual grub2 config doesn''t work automaticlly at boot time. i configured the arg "dom0_mem=4096M" in the grub.cfg section multiboot as shown bellow: *** menuentry ''Debian GNU/Linux, with

On Sat, 2013-09-28 at 20:59 -0700, Tril wrote: > Backtrace from manual run of the buggy GrubConf.py: > # python /usr/lib/xen-4.1/lib/python/grub/GrubConf.py grub2 grub.cfg > WARNING:root:Unknown directive load_video > WARNING:root:Unknown directive terminal_output > WARNING:root:Unknown image directive load_video > Traceback (most recent call last): > File

I installed CentOS 7 on a Shuttle X27D box (dual-core Atom 330), and so far it seems to work fine, but it didn't set up a Grub2 entry for the existing Windows XP installation in the first partition (MBR). Running os-prober generates no output. fdisk shows that the NTFS partition is still present as /dev/sda1, and still has the bootable flag set. I added a menuentry for Windows to the end of

This grub.cfg from a default fedora 19 Beta install caused pygrub failures.The previous pygrub commit fixed taht. So this example file added for reference. Signed-off-by: Marcel Mol <marcel@mesa.nl> --- tools/pygrub/examples/fedora-19.grub2 | 117 +++++++++++++++++++++++++++++++++ 1 files changed, 117 insertions(+), 0 deletions(-) create mode 100644 tools/pygrub/examples/fedora-19.grub2