similar to: xcp + ubuntu + openvswitch VLAN problem

hi all, i use xcp on ubuntu 12.04 with both linux and windows instances, everything fine, but after the host run few days, i can not connected it again and i try to use dell compute management port to access the console, but it''s just black screen and nothing response~~, i have to reboot it~~ and also , i can not find any usefull message in syslog or xcp log~~, it looks like a cpu

I am planning to schedule a monthly XCP meeting for the community and am struggling with when to host the call. As we are a global community, there is no single optimal time to host the meeting. In an effort to support the most likely attendees, please send me your time zone if you plan to participate in these calls. I will track the most common time zones in an effort to maximize attendance. All

I am planning to schedule a monthly XCP meeting for the community and am struggling with when to host the call. As we are a global community, there is no single optimal time to host the meeting. In an effort to support the most likely attendees, please send me your time zone if you plan to participate in these calls. I will track the most common time zones in an effort to maximize attendance. All

Hi, I''ve installed XCP 0.5 and I''m following these steps: http://xenbits.xen.org/xapi/install.html to install ddk VM. But I can''t get network working. I tried to create a vif under xenbr0 then assigned mannually a IP address and to create a vif under xapi0. But in both cases I can ping only dom0 IP. What am I doing wrong? Thanks in advance. -- Sergio Roberto

Hello all! I try to use network filters for openvswitch interfaces.  This is the xml configuration of my bridge interface <interface type='bridge'>    <mac address='00:11:22:33:44:55'/>    <source bridge='virbr1'/>    <virtualport type='openvswitch'>         <parameters interfaceid='0529d6b5-627c-4330-803f-0d7018e6d496'/>   

Hello, I have been playing with the XCP for a while now, and must say I''m very exited about the technology. I had no prior experience with Xen so it has taken me a while to understand the concepts, but now I feel most important issues are solved and I''ve purchased some hardware to build my (tiny) cloud on. The box is a Supermicro 1026TT-IBXF, so I have 2 x Ethernet and 1 x

hi all, i meet a big problem, when i finish install xcp-xapi on ubuntu 12.04, i set grub to go into xen 4.1 kernel when startup and set echo ''TOOLSTACK="xapi"'' > /etc/default/xen when i reboot and login to the system , i got a lot out of memory error and all process be killed, seem like kernel crash. can anyone help me about that ? thanks.

Package: xcp-xe Version: 1.3.2-14 Severity: important I created an internal network using xe network-create name-label='Private NAT network' Looking with brctl, I could see xapi0 had been created by the tools. However, the network does not appear in openxenmanager. I even restarted openxenmanager, it still didn't appear. Then I deleted the network and created it again from

hi all, im peter, i found the post here http://www.gossamer-threads.com/lists/xen/users/229738 i build a small test env, with 2 vm in 1 server with xcp 1.1.0 i use xe network-create and xe vlan-create to build the vlan for each vm. then i got 2 bridge like xapi1 and xapi2, and in the ovs-vsctl list port i can see all these info about fake-bridge and vlan tag is correct. but when i start 2

Hello, I am trying to setup Debian Squeeze as domU, but I get the message below during the setup process: No Ethernet card was detected on Debian Squeeze domU install And it asks to select the driver to me. I followed the instructions at page 27 of the guest.pdf manual, but there is no indication on how to set-up the bridge in order to make the ethernet interface available for the guest. How

I just tried to setup another domain on a server running 1 domain. When i try to start the domain it gives me an error Error: Device 0 (vif) could not be connected. Backend device not found. The entry in my xen config file for the disks is disk = [''phy:/dev/xen001/xen2-fun,sda1,w'',''phy:/dev/xen001/xen2-fun-swap,sda2,w''] Looking at /var/log/xend.log, i found

Package: xcp-xapi Version: 1.3.2-14 Severity: important I chose the Open vSwitch (ovs) networking mode when I installed XCP # cat /etc/xcp/network.conf openvswitch Whenever I boot a VM, I notice that the vif interface is created (e.g. vif1.0) on dom0, and the vif is added to the ovs bridge (I can see it in the output of ovs-vsctl show) However, there is no connectivity, I can't ping the

https://bugzilla.netfilter.org/show_bug.cgi?id=1177 Bug ID: 1177 Summary: Export 'ct_zone' field. Product: ulogd Version: SVN (please provide timestamp) Hardware: All OS: All Status: NEW Severity: enhancement Priority: P5 Component: ulogd Assignee: netfilter-buglog at

Package: xen-hypervisor-4.0-amd64 Version: 4.0.1-5.2 Hi, We're seeing weird behaviour regarding network traffic between a Xen dom0 and domU. I reported this issue yesterday to the openvswitch-discuss mailing list, but it seems this could also be a (regression?) bug in the xen hypervisor or the linux kernel... (we've upgraded xen-hypervisor-4.0-amd64 4.0.1-4 -> 4.0.1-5.2 and

Package: xcp-xapi Version: 1.3.2-14 Severity: important I imported a HVM from a legacy xm environment. It is attached to one vif, the xenapi management vif It fails to start: # xe vm-start uuid=f2ba4767-7b4f-b416-3da6-3fe059ebfc37 The server failed to handle your request, due to an internal error. The given message may give details useful for debugging the problem. message: device model

Hey there, I hope anyone can bring some light in the following problem. <interface type='bridge'> <source bridge='cloudbr0'/> <mtu size='2000'/> <mac address='02:00:74:76:00:01'/> <model type='virtio'/> <virtualport type='openvswitch'> </virtualport> <vlan trunk='no'> <tag

hi all, i just found a bug from xapi code network_utils.ml: let is_physical name = try let link = Unix.readlink (getpath name "device") in (* filter out device symlinks which look like /../../../devices/xen-backend/vif- *) not(List.mem "xen-backend" (String.split ''/'' link)) with _ -> false i use xcp + ubuntu 12.04, in my /sys/class/net/ dir it