similar to: Centos 6.3 Network bnx2 Problem on HP DL360

Hi Michael: Sorry to brother. But I''ve been suffered this issue quite a long time. My test environment is 2.6.32.36 + xen 4.0.1 + bnx2, 2.3. Also cpu idle is disabled in grub. Grub info: title Red Hat Enterprise Linux Server (2.6.32.36xen) kernel /xen-4.0.1.gz iommu=off x2apic=off console=com1,vga com1=115200,8n1 noreboot cpuidle=0 cpufreq=none

I just kickstarted a new machine with the latest CentOS 6.2 files, including kernel 2.6.32-220.13.1.el6.x86_64. It came up without network interfaces. dmesg says: bnx2: Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.2.1 (Dec 18, 2011) alloc irq_desc for 36 on node -1 alloc kstat_irqs on node -1 bnx2 0000:01:00.0: PCI INT A -> GSI 36 (level, low) -> IRQ 36 bnx2 0000:01:00.0:

Hi, i test a xen-patched kernel 2.6.31.10 (kernel from kernel.org with the suse patches) on a system with a boradcom net extreme II (5709) nic using the module bnx2. The nic does not run with this kernel. I get: bnx2 0000:01:00.0: map irq failed Any experiences? Best Regards - Michael Schmidt _______________________________________________ Xen-users mailing list

Hello list, I have two differents installation Xen Hypervisor on two identical physical server, on the same switch : The problem is on my new server (Xen 4.0.1 with pvops kernel 2.6.32.24), I have bad performance on bandwidth I have test with a files copy and "iperf". Result iperf average: Transfert Bandwidth XEN-A -> Windows

I have a broadcom bcm5722 and a dual intel pro/1000 pt nic in a dell t110. The setup sees the cards and i put them into automatic mode. After the install no cards are detected at all. Astaro 8.01 detects and utilizes all of these cards just fine. I have also tried ubuntu server 10.04 lts and they work fine. I'm curious if this is a bug with Centos 6?

Hi all, I have a problem when from domU I need to configure a network interface. My system configuration is the next: dom0: xen 3.4.3 with 2.6.18-238.9.1.el5xen kernel, making pci back from a network card. All ok. This is the result from "lspci -v -s 09:00.0" 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) Subsystem: Broadcom

Hoping someone else has seen this before. I have a few dozen Dell R610 systems with CentOS 5.2 that are using kernels from 5.3 and 5.4 (2.6.18-128.1.10.el5 & 2.6.18-164.6.1.el5), that at random lose layer 2 network connectivity either partially or totally. Running tcpdump on the interface reveals only ARP broadcasts, no responses. Switch reports no packets being received on the interface.

Hi all I'm trying to setup second ethernet on Dell 2950 server but there isn't any eth1 device (in the bios are ON) # dmesg |grep eth eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 001c23d878bb eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 001c23d878bd

Getting "bnx2i: iSCSI not supported, dev=eth0" for all the NIC adapters on all of my R710's running CentOS 5.5. Here is an sample of the error messages: bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details. bonding: bond0: setting mode to active-backup

Hi, I''ve run into the same issue as: http://lists.xensource.com/archives/html/xen-users/2006-07/msg00599.html In that, running the network bridge script kills networking completely, trying to ping the gateway gives me destination host unreachable. The card is: 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 11) Using the bnx2 module:

I''m experimenting with xen + iscsi, and I founded that under heavy stress domU''s can crash entire system, I''ve reproduced this many many times. My system is like this Software: - iSCSI Enterprise Target v0.4.13 - RedHat AS4 update 4 64bit + Xen 3.0.3-0 Kernel 2.6.16.29 + Open iSCSI v2.0.730 (Initiator) - Bonnie++ v1.03a VM: - Debian 3.1r3 + Open iSCSI v2.0.730

I have a new x3655 IBM and whenever the /etc/xen/scripts/network-bridge script starts, the ethernet would no longer work. This post isn''t about the cause, but the fix. I did a lot of tcpdumps and Googling, but I''ll spare you that. All they do is prove that yes, there is an issue. :) I tried Debian 4.0 i386/amd64 and Ubuntu 7.04 Server i386/amd64 and they all exhibit the

The network device operation for reading statistics is only called in one place, and it ignores the return value. Having a structure return value is potentially confusing because some future driver could incorrectly assume that the return value was used. Fix all drivers with ndo_get_stats64 to have a void function. Signed-off-by: Stephen Hemminger <sthemmin at microsoft.com> ---

The network device operation for reading statistics is only called in one place, and it ignores the return value. Having a structure return value is potentially confusing because some future driver could incorrectly assume that the return value was used. Fix all drivers with ndo_get_stats64 to have a void function. Signed-off-by: Stephen Hemminger <sthemmin at microsoft.com> ---

I totally agree with Luc Boudreau about this problem. On modern branded server they ALL use Broadcom chipset... I must admit that: a) lot of people are experiencing the problem but can tolerate it or b) someone already experienced this problem and solved it Lets'' approach the problem pragmatically... just start with a survey on the list. ... hope we solve this issue soon. Ivan

I use bonding under CENTOS4.5 x32_62. I have these weird messages when I'm restarting network. Do you have any ideas how to fix this? (there is similar bug for centos5 http://bugs.centos.org/view.php?id=2404, but the author says that it worked for him in centos4...) Thanks Vitaly Dec 17 08:34:21 3_10 kernel: bonding: Warning: the permanent HWaddr of eth0 - 00:1A:64:0A:DC:9C - is still in

I am having an extremely strange issue with a BL460c1 (G1) blade on a c7000 enclosure. I could not for the life of me get the machine to ping the gateway or any other blade on the same enclosure (yes, the subnet mask was correct & quadruple-checked); although pinging to the local IP works. I was almost convinced that it was a network or hardware issue; until I asked someone to try

Package: xen-hypervisor-3.4-amd64 and linux-image-2.6.32-5-xen-amd64 Version: 3.4.3-1 and 2.6.32-15 Hello all, GRUB-PC does not automatically populate Xen related parameters in /boot/grub/grub.cfg so I added them manually (see below). All the packages involved on my Dell PowerEdge R710 running Debian GNU/Linux Squeeze AMD64 are from the Squeeze repository. There are four (4) 1TB SATA HDD

Hello, I''ve this strange problem. When Xen kernel start and it try to start eth devices, network doesn''t work. It seems to be a problem with NICs firmware. Anyone had this problem? Do you know where I can download firmware upgrade? (on DELL''s site I''ve just searched...) Thanks, Carlo No virus found in this outgoing message. Checked by AVG Free Edition.

Hello, I can''t solve my problem. I want a 32 bits Lenny domU into a 64 bits Lenny dom0. I plan to use pygrub for that (xen 3.2.1). So, I tried to debootstrap a 32 bits domU into a 64 bits dom0. debootstrap --arch=i386 --include=libc6-xen,firmware-bnx2,linux-image-2.6.26-1-xen-686,linux-modules-xen-686,linux-image-xen-686,grub --components=main,contrib,non-free lenny /mnt/xen