similar to: Centos 6.4 - yum update gives: Error: kernel conflicts with bfa-firmware

Someone on this list uses the address @sedwards.com I doubt this is their actual email address as there is no MX record for sedwards.com and I can't find registration for their domain either. Part of my mail servers reject these emails because they cannot be replied to, or are likely to be spam. Every so often I get a mail from the list management to say that I've been unsubscribed

Just a note that I did a little work to extend FreePBX distro with some extra Fail2Ban which deals with some drive-by SIP registration attempts. My regex is poor to middling, but the steps detailed here: http://www.coochey.net/?p=61 manage to stop IPs which try to authenticate against Asterisk which FreePBX were not able to stop before. I would welcome any improvements anyone would care to

Hi List, I''m in the process of setting up softflowd 0.9.9 on a Centos 6.4 system (compiled from source tarball). The daemon will listen to an unused interface that is receiving port mirrored traffic (a.la. Span port) I am planning on using the softflowd init script and sysconfig file provided in the tar ball. Do I need to manually put the unused interface into promiscuous mode, or

Every so often recently I've seen the load on my heavily under-used dovecot server (1 mailbox) rise up to 1 A top shows imap-login to causing the issue. I have checked /var/log/secure, /var/log/maillog, /var/log/messages and cannot see anything unusual. Anybody else seen something like this? # 2.2.5: /etc/dovecot/dovecot.conf # OS: Linux 2.6.32-358.14.1.el6.x86_64 x86_64 CentOS release

Hi, I hope someone can help me, I cannot seem to get a system's ethernet interface to correctly work in promiscuous mode... I have a Centos 6.4 system with 2 bnx2 interfaces on it. I have set up eth1 in promiscuous mode and am sending traffic to it using the port mirroring configuration on a Nortel 3510-24T switch. The switch reports that it is sending a fair amount of traffic to the

Using CentOS 5.8: Currently on my workstations, when I press the power button the computer immediately does a 'shutdown -h now' (per /etc/acpid/events/power.conf). Is there a way to change it so that a confirmation dialog comes up, rather than an immediate shutdown? I assume that I am going to need to change that power.conf file to tell some program that the power button's been

Hi, I am running CentOS 6.4 on a remote server. when i run the below command, it prints out the headers too. is there a way to remove headers using the below command line *top -b -p 22657 > topcpu.txt* Regards, Kaushal

Dear All Can you please let me know how can I check if a radius server application is present on my centos server ? Thank you

Hello, can someone recommend a good and free Softphone for Windows which does not display advertisments inside the program? We have X-Lite but free version display advertisments. thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20140608/c3a9e887/attachment.html>

Hello list, In the past we have instructed users to perform 'xhost +' from their centos desktop, then set the DISPLAY variable on a remote computer to forward their display back to the desktop. This does not seem to work on centos 6 - but it did work in centos 5. It works from a vnc session on the desktop machine, but does not work from the local desktop. We would typically use a display

Hello, I need to buy an ultrabook. Any recommendations for something that would work out of the box more or less? I do not want a Chromebook (or anything ARM) or one of these new "touch" laptops, in fact I'm after a nice matte screen. Budget is modest-ish (?500/$800) so dont go crazy. :) Thanks! -- Sent from the Delta quadrant using Borg technology! Nux! www.nux.ro

Hi, though this is a bit of a side question, has anybody had an issue while running Outlook 2010 with Dovecot? The reason why I am asking is that I have setup a Dovecot 2.1.7 server on FreeBSD which works fantastically with Thunderbird but Outlook seems to be twice as slow in transferring information across?? # dovecot -n # 2.1.7: /usr/local/etc/dovecot/dovecot.conf # OS: FreeBSD 8.2-RELEASE

What is the easiest way to convert a webpage into a jpg or png file? I've seen several programs that can do various conversions, but nothing open source that can do it in a single conversion. Just wondering if anyone on the list has suggestions for something I can put into a script to convert a webpage into a file I can use with my screensaver. c

On 05/01/2015 15:14, Philippe BOURDEU d'AGUERRE wrote: > Happy new year ! > > We have a SuperMicro server with a LSI MegaRAID 9260-4i controller. > > Since Centos 6.6 update (kernel 2.6.32-504), the controller doesn't > initialize at boot. Reverting to kernel 2.6.32-431 allows server to > boot fine. > I have a similar system, and don't have your problem: #

Greetings- I'd like to configure multiple copper NICs on a server running CentOS 6.2 in a LAGG configuration for better throughput to the core switch. After quite a bit of searching, I'm not seeing anything of the sort. Is LAGG specific to the BSD world and the HP switches I'm running? Or, does it go by a different name? Bonding perhaps? If so, is bonding compatible with LAGG? --Tim

after having my own dnsbl feeded by a honeypot and even mod_security supports it for webservers i think dovecot sould support the same to prevent dictionary attacks from known bad hosts, in our case that blacklist is 100% trustable and blocks before SMTP-Auth while normal RBL's are after SASL i admit that i am not a C/C++-programmer, but i think doing the DNS request and in case it has a

Hey All, I'm developing a site on a VPS that comes stock with dovecot 1.2.17 and I'm trying to setup some functionality that is very specific to our business model. My question is this: How do I create (programatically) aliases for a forwarder? I have an address, email at domain.com that gets sent to a php script and I want users to be able to send to that script via any number of

Hi, dose anybody did a dovecot update from the original 1.0.7 to e.g. 1.1 or 1.2 from atrpms repository? We dont have any special settings; Each user one mbox mailbox. About 500 imap/pop3 accounts, 400GB data. Any suggestions and comments are welcome. Regards . G. Reinicke -- G?tz Reinicke - IT-Koordinator - Filmakademie Baden-W?rttemberg GmbH

Hi. Somebody in the Spanish CentOS mailing list is asking how to move from CentOS 4.8 to 4.9. He cannot upgrade to 5 or 6 at this moment. Any Hints / Howto? I would pass the translated answer to the Sp. list. Thanks & Regards, Jesus

Hi, after IPv6 day, I was wondering if our server were really secure... And, I know we should switch on IPv6 everywhere but... it will take some time. Usually, we disable(d) IPv6; so we are not running ip6tables. Can I start ip6tables in all cases (even if only IPv4) just to be on the safe side? On CentOS 6 servers, I use the --noipv6 in the kickstart files and I removed NetworkManager; but