similar to: raid 1 question

Is there a reason why after a software raid install (from kickstart) that md1 is always unclean. md0 seems fine. boot screen says md1 is dirty and cat /proc/mdstat show md1 as being rebuilt. Any ideas? Jerry --------------- my kickstart -------------- echo "bootloader --location=mbr --driveorder=$HD1SHORT --append=\"rhgb quiet\" " >

Hi. CENTOS 7.6.1810, fresh install - use this as a base to create/upgrade new/old machines. I was trying to setup two disks as a RAID1 array, using these lines mdadm --create --verbose /dev/md0 --level=0 --raid-devices=2 /dev/sdb1 /dev/sdc1 mdadm --create --verbose /dev/md1 --level=0 --raid-devices=2 /dev/sdb2 /dev/sdc2 mdadm --create --verbose /dev/md2 --level=0 --raid-devices=2

Ok, this is the case: I've got two raid-5 arrays with software raid, both with three disks. Setup: md0 has hdb2, hdd1 and sda1 md1 has hdb5, hdd3 and sda3 Tonight, the system lost power due to a power spike. The result was a reboot where it attempted to fix the raid, but it didn't exactly work. I have now booted a live CD and using utilities there. It seems the checksum value is

Hi I have a Raid 1 centos 4.4 setup and now have this /proc/mdstat output: [root at server admin]# cat /proc/mdstat Personalities : [raid1] md2 : active raid1 hdc2[1] hda2[0] 1052160 blocks [2/2] [UU] md1 : active raid1 hda3[0] 77023552 blocks [2/1] [U_] md0 : active raid1 hdc1[1] hda1[0] 104320 blocks [2/2] [UU] What happens with md1 ? My dmesg output is: [root at

Hi all, Please excuse the many posts. Wondering if any one can help me with the the setup. I have 2x2TBdisks. I would like to mirror them. I would like to create two LVMs so that I can snap shot from one to the other. During Centos 6 install, how would I go about this as its confusing? So far I am here; 1) Created the following raid devices; md0 500MB (use it for /boot) md1 4000MB (use it

I think I have solved my issue and would like some input from anyone who has done this for pitfalls, errors, or if I am just wrong. Centos 5.x, software raid, 250gb drives. 2 drives in mirror, one spare. All same size. 2 devices in the mirror, one boot (about 100MB), one that fills the rest of disk and contains LVM partitions. I was thinking of taking out the spare and adding a 500gb drive. I

hi all! back in Aug several of you assisted me in solving a problem where one of my drives had dropped out of (or been kicked out of) the raid1 array. something vaguely similar appears to have happened just a few mins ago, upon rebooting after a small update. I received four emails like this, one for /dev/md0, one for /dev/md1, one for /dev/md125 and one for /dev/md126: Subject: DegradedArray

I have configured 2x 500G sata HDD as Software RAID1 with three partitions md0,md1 and md2 with md2 as 400+ gigs Now it is almost 36 hours the status is cat /proc/mdstat Personalities : [raid1] md0 : active raid1 hdb1[1] hda1[0] 104320 blocks [2/2] [UU] resync=DELAYED md1 : active raid1 hdb2[1] hda2[0] 4096448 blocks [2/2] [UU] resync=DELAYED md2 : active raid1

Hi all, I'm setting up Centos4.2 on 2x80GB SATA drives. The partition scheme is like this: /boot = 300MB / = 9.2GB /home = 70GB swap = 500MB The RAID is RAID 1. md0 = 300MB = /boot md1 = 9.2GB = LVM md2 = 70GB = LVM md3 = 500MB = LVM Now, the confusing part is: 1. When creating VolGroup00, should I include all PV (md1, md2, md3)? Then create the LV. 2. When setting up RAID 1, should I

I'm playing with software RAID and LVM in some virtual machines and I've run into an issue that I can't find a good answer to in the docs. I have the following RAID setup: md0: sda1 and sdb1, RAID 1. This is /boot md1: sda2 and sdb2, RAID 1. This is a PV for LVM. VolGroup00, this is the volume group and md1 is the only PV in it. LogVol00 is swap LogVol01 is / LogVol02 is /home

I am using a kickstart file for CentOS 7 raid / --device=md0 --fstype="xfs" --level=1 --useexisting raid /home --noformat --device=md1 --level=1 --useexisting It is erroring out on the --useexisting. The exact text is: RAID volume "0" specified with "--useexisting" does not exist. What did I do wrong? Jerry

Hi list, I'm new with UEFI and GPT. For several years I've used MBR partition table. I've installed my system on software raid1 (mdadm) using md0(sda1,sdb1) for swap, md1(sda2, sdb2) for /, md2 (sda3,sdb3) for /home. From several how-to concerning raid1 installation, I must put each partition on a different md devices. I've asked times ago if it's more correct create the

I have a machine on CentOS 5 with two disks in RAID1 using Linux software RAID. /dev/md0 is a small boot partition, /dev/md1 spans the rest of the disk(s). /dev/md1 is managed by LVM and holds the system partition and several other partitions. I had to take out disk sda from the RAID and low level format it with the tool provided by Samsung. Now I put it back and want to reassemble the array.

I have a system that is RAID -1 configured as /dev/md0 is /dev/hda1 /dev/hdb1 /dev/md1 is /dev/hdb3 /dev/hdb3 it seems as though /dev/hda has failed.... I have another disk (identical model) that I can replace hda with. I know about the commands fdisk to repartion and raidhotadd /dev/md0 /dev/hda1 and raidhotadd /dev/md1 /dev/hda3 (to be ran after the system boots). BUT... how do I now get

Hello. A couple of years ago I installed two file-servers using kickstart. The server has two 1TB sata disks with two software raid1 partitions as follows: # cat /proc/mdstat Personalities : [raid1] md1 : active raid1 sdb4[1] sda4[0] 933448704 blocks [2/2] [UU] md0 : active raid1 sdb1[1] sda2[2](F) 40957568 blocks [2/1] [_U] Now the drives are starting to be failing and next week

I have noticed that when I do software raid installed (RAID1) that I reboot and one of the first things it says is md1 is not in sync doing background reconstruction... md0 is my /root partition md1 is my /home partition why would md1 not be in sync after an install. Jerry

I installed Centos 6.x 64 bit with the minimal ISO and used two disks in RAID 1 array. Filesystem Size Used Avail Use% Mounted on /dev/md2 97G 918M 91G 1% / tmpfs 16G 0 16G 0% /dev/shm /dev/md1 485M 54M 407M 12% /boot /dev/md3 3.4T 198M 3.2T 1% /vz Personalities : [raid1] md1 : active raid1 sda1[0] sdb1[1] 511936 blocks super 1.0

Hi, This is my current config: /dev/md0 -> 200 MB -> sda1 + sdd1 -> /boot /dev/md1 -> 36 GB -> sda2 + sdd2 -> form VolGroup00 with md2 /dev/md2 -> 18 GB -> sdb1 + sde1 -> form VolGroup00 with md1 sda,sdd -> 36 GB 10k SCSI HDDs sdb,sde -> 18 GB 10k SCSI HDDs I have added 2 36 GB 10K SCSI drives in it, they are detected as sdc and sdf. What should I do if I

I just replaced two md-raided (RAID1) disks with bigger ones and decided to check out how far I get with them when I put them in another machine. The kernel boots and then panics when it wants to mount the root filesystem on the disk. md: Autodetecting RAID arrays md: autorun md: autorun DONE < not sure if this means it was successful or failed, I rather think it failed because it

Thanks for all the responses. A little more digging revealed: md0 is made up of two 250G disks on which the OS and a very large /var partions resides for a number of virtual machines. md1 is made up of two 2T disks on which /home resides. Challenge is that disk 0 of md0 is the problem and it has a 524M /boot partition outside of the raid partition. My plan is to back up /home (md1) and at a