similar to: [syslinux.exe] Failures to use\install on xp+ntfs

Platform: MS XP 1. cfg file: prompt 1 timeout 150 display /downloadedPrograms/syslinux/syslinux.cfg default xp label xp com32 chain.c32 append hd0 1 ntldr=/ntldr label de com32 chain.c32 append hd0 2 label memtest linux memtest86+.bin label hello com32 hello.c32 2. Installed by >From xp cmd prompt:

On Sat, Sep 14, 2013 at 04:51:52PM -0400, Gene Cumm wrote: > On Sat, Sep 14, 2013 at 3:20 PM, Regid Ichira <regid23 at nt1.in> wrote: > > > label xp > > com32 chain.c32 > > append hd0 1 ntldr=/ntldr > > > 2. Installed by > > From xp cmd prompt: > > c:\downloadedPrograms\syslinux\syslinux.exe --active \ > >

On Sun, Sep 15, 2013 at 04:31:09PM +0300, Ady wrote: > > > Platform: MS XP > > > > 1. cfg file: > > prompt 1 > > timeout 150 > > display /downloadedPrograms/syslinux/syslinux.cfg > > > > default xp > > label xp > > com32 chain.c32 > > append hd0 1 ntldr=/ntldr > > label de > >

On Sun, Sep 15, 2013 at 11:14:05PM +0300, Ady wrote: > > > On Sun, Sep 15, 2013 at 04:31:09PM +0300, Ady wrote: > > > > > > > Platform: MS XP > > > > > > > > 1. cfg file: > > > > prompt 1 > > > > timeout 150 > > > > display /downloadedPrograms/syslinux/syslinux.cfg > > > > > > >

On Tue, Sep 17, 2013 at 09:57:26AM +0300, Ady wrote: > > > On Sun, Sep 15, 2013 at 11:14:05PM +0300, Ady wrote: > > > > > > > On Sun, Sep 15, 2013 at 04:31:09PM +0300, Ady wrote: > > > > > > > > > > > Platform: MS XP > > > > > > > > > > > > 1. cfg file: > > > > > > prompt 1

On 2019-4-5 11:28, Ady Ady via Syslinux wrote: >> >> #This item fails >> label normal >> menu default >> menu label Boot from ^hard disk >> com32 chain.c32 hd1 > > >>From the Syslinux boot menu, press [Esc] in order to get to the boot prompt. At > the boot prompt, type in: > > normal > > and press [Enter]. > > Is there

Greetings, I encounter a problem that should be basic, but I can't get a clue. I have 8G USB disk formatted as FAT32. I run (syslinux -i -s -r -m H:) to make it bootable, and write syslinux.cfg according to the documents, but it will not boot some items. Syslinux is 6.03, bios files used. The whole syslinux.cfg file:

Hello list, I have a question concerning the possibility of booting one of two Windows systems installed on two partitions. In case with one Windows system and one Linux system, I can chainload grub or windows loader, and this is OK. But in case with two Windows systems, when I installed second system, the installer added multi boot loader(I think it's called bootmgr), and then I can't

When booting windows I currently have to use an extracted boot sector to chain-load the OS, is there any merit to creating a method to execute NTLDR directly using a /reverse engineered/ version of the boot sector?

Lu Wei, What Hard drive are you also trying to boot? The first and only fixed drive inside a computer? If so would the line to boot a local HD not be: LABEL LOCAL MENU LABEL Local operating system in harddrive (if available) kernel chain.c32 append hd0 -Adan On Thu, Apr 4, 2019 at 8:56 AM Adan Calderon <adancalderon at gmail.com> wrote: > > Lu Wei, > > For the DOS portion

I've a 100 MB FAT32 partition which is the first primary (and active) partition of my hard disk. I've installed SYSLINUX to that drive. I've another primary partition which I installed Windows XP to it (and this partition is NTFS). I want to have a boot menu, so I used chain.c32 and menu.c32 My syslinux.conf file is as below: LABEL WinXP COM32 chain.c32 APPEND hd0 2 ntldr=ntldr But

Hey list, I have an older 2005 Uniwill 259ia3 with a Phoenix bios. Flash booting is limited to keys 512 MB or less! Here's my setup recipe: used the HP utility v. 2.0.6 giving me this geometry ---------------- fdisk -l ----------- Disk /dev/sdb: 493 MB, 493879296 bytes 255 heads, 63 sectors/track, 60 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start

Hi all, I have observed a problem where, under legacy BIOS booting mode on the DL360g9, memdisk fails to execute. The same mechanism works fine on the DL360g8. The system displays the below on the console and ceases to respond and must be power cycled. Updating the firmware didn't help. There didn't appear to be any similar issues on the mailing list unless I missed them. Wondering if

On 2014/3/7 ?? 05:23, Gene Cumm wrote: > On Thu, Mar 6, 2014 at 10:55 AM, Bryan Romine <bromine1027 at gmail.com> wrote: >> Sorry for the confusion, I am actually using 6.02. It turns out that I was >> trying to use the 32-bit efi binary to load 64-bit kernels. I switched to >> using "syslinux64.efi" but it hangs during boot, just before loading the >>

On Thu, Feb 2, 2017 at 1:26 PM, Ady Ady via Syslinux <syslinux at zytor.com> wrote: > > > Hi all, > > > > I have observed a problem where, under legacy BIOS booting mode on the > > DL360g9, memdisk fails to execute. The same mechanism works fine on the > > DL360g8. The system displays the below on the console and ceases to > > respond and must be

I was trying to set up a USB stick with syslinux.exe, on a XP machine. Had the following problems: 1. Tried: 1.1 from XP native cmd shell: E:\>syslinux\syslinux.exe --directory /syslinux --install --force --mbr --active e: 1.2 and a similar command from cygwin. where e: is the USB stick. With cygwin I got a segmentation fault. With XP

My reason for patching circa line 225 is that I think it is clearer. The reason for patching circa line 575 is http://bugs.debian.org/647603. They concluded that a .0 file is recognized not only by PXELINUX. And what is NBP? --- a/doc/syslinux.txt 2011-12-07 04:53:29.201556663 +0200 +++ b/doc/syslinux.txt 2011-12-07 04:50:11.000000000 +0200 @@ -221,7 +221,6 @@ LABEL label The following

On 2019-4-10 1:20, Ady Ady via Syslinux wrote: >>> Test #2: if you unplug the USB and reboot the system, can you >>> successfully boot directly to the HDD's OS? >>> >> Yes. The only HDD, NTFS, WindowsXP native boot loader ntldr. > > > Let me rephrase my question. It was/is clear that you used to be able > to boot Windows when the first boot

So when you boot from only your hard drive attached, it is the primary and only drive. It loads the master boot record that load the NT Loader boot code that is then configured to load the operating system from the primary partition on the primary drive. When you boot from the USB drive, you make it the Primary drive. You then tell it to load the MBR fromt the secondary drive. The secondary

This patch introduces extra functionality to chain.c, mainly with reference to BPB adjustments, but not only that. It expects 3 small patches I sent earlier (they are included for easy reference, patches 1-3/4). The changes introduced are: 1) file and boot sector use separate options to control load address and jump address (if applicable). Options are as described below: *