similar to: ethtool-like utility for FreeBSD

Hi! There is a posting public about Intel ethernet adapters and their packets of death: http://blog.krisk.org/2013/02/packets-of-death.html Now, how can we test the EEPROM from FreeBSD, similar to the ethtool of Linux ? Thanks for any pointer! -- pi at opsec.eu +49 171 3101372 7 years to go !

Dear Srs, I'm trying to monitor CPU temperatures in a PowerEdge 860 server, running CentOS 5.1 with 2.6.18-53.1.6.el5 kernel, using lm-sensors v2.10.0. Running "sensors-detect" I get: ====================================================================== (..) We can start with probing for (PCI) I2C or SMBus adapters. You do not need any special privileges for this. Do you want

Hi Alex, since I have no knowledge of the apcsmart driver, nor much time currently, I've forwarded your msg to the NUT development list. I hope somebody can take over your call. btw, please subscribe to the list for further discussions... 2007/5/28, Alex Brodsky <abrodsky at acs.uwinnipeg.ca>: > Hi, > > My name is Alex Brodsky, I am a faculty member at University of >

Hullo Everybody I have taken the steps below and I failed to get a device similar to /dev/xvda in DOM 0 where am I getting it wrong Create VDI, *[root@virtualintranet /]# xe vdi-create sm-config:type=raw sr-uuid=b303be09-6a32-8d94-d248-7551860fbc3f name-label="Centos-Vdi" virtual-size=20GiB type=user* eefa9066-a991-44c3-b537-d20d65f3d10c create VBD *[root@virtualintranet /]# xe

Hi Chris 2017-03-23 16:58 GMT+01:00 Sonic <sonicsmith at gmail.com>: > On Thu, Mar 23, 2017 at 11:26 AM, Gene Heskett <gheskett at shentel.net> > wrote: > > Have you the file to be used to update the EEPROM with? > > Eaton shows a firmware file: > https://powerquality.eaton.com/Support/Software-Drivers/ > Downloads/5P-UPS-firmware.asp > > However I'm

Hi, We have an old Win98 box at work that is used for programming GALs and EEPROMs, however we find that if the file is modified on the Unix side the Win98 box doesn't notice. This is rather annoying when you are iterating a design as you can imagine! One work around is to open a DOS box and 'type' the file - this seems to force it to re-get the file. Does anyone have any

Hello, I'm having problems with lm_sensors on the motherboard Supermicro X6DH8-G2+ sensors-detect gives me the output attached in the textfile sensors-detect-output.txt As soon as I execute the recommended 'modprobe smbus-arp' I receive the following message: FATAL: Module smbus_arp not found. When I execute sensors, I receive the following:

On Thu, Mar 23, 2017 at 11:26 AM, Gene Heskett <gheskett at shentel.net> wrote: > Have you the file to be used to update the EEPROM with? Eaton shows a firmware file: https://powerquality.eaton.com/Support/Software-Drivers/Downloads/5P-UPS-firmware.asp However I'm not sure if it is for the questionable EEPROM and if so maybe it is downlevel from the current reported firmware. upsc

Hi, V have used the tool chains arm-elf-gcc-3.2.1.tar.bz2 arm-linux-gcc-3.4.3_1.0.1tar.bz And v r using the - Cirrus-arm-linux-2.0.8-full.tar.bz2(kernel version 2.6) pls help us. V ll be using the "libvorbis-1.2.0.tar.gz" tool chain..... EP9302 Overview The EP9302 is an ARM920T-based system-on-a-chip design with a peripheral set targeted to a variety of applications:

2017-03-23 14:29 GMT+01:00 Sonic <sonicsmith at gmail.com>: > Hello > Hi Chris > Sorry if any of this is obvious - I'm new to NUT. > > NUT via upsc is displaying (edited for length): > > device.model: Eaton 5P 2200 > device.type: ups > driver.name: usbhid-ups > ups.alarm: Fatal EEPROM fault! > ups.status: ALARM OL CHRG > ups.test.interval: 604800

On Thursday 23 March 2017 09:29:55 Sonic wrote: > Hello, > > Sorry if any of this is obvious - I'm new to NUT. > > NUT via upsc is displaying (edited for length): > > device.model: Eaton 5P 2200 > device.type: ups > driver.name: usbhid-ups > ups.alarm: Fatal EEPROM fault! > ups.status: ALARM OL CHRG > ups.test.interval: 604800 > ups.test.result: Done and

Hi. I got this on today's RELENG_6 with Broadcom BCM5722 A0, ASIC rev. 0xa200. >From dmesg (bge related): bge0: <Broadcom BCM5722 A0, ASIC rev. 0xa200> mem 0xe8400000-0xe840ffff irq 16 at device 0.0 on pci2 bge0: firmware handshake timed out, found 0x4b657654 bge0: firmware handshake timed out, found 0x4b657654 bge0: EEPROM read timed out bge0: failed to read EEPROM device_attach:

Hi Michal, I'm cc'ing the NUT development mailing list. you should also subscribe to it. 2010/10/28 Michal Soltys > Greetings > > I have loads of relatively old smart upses that I currently control using a > bit patched version of apcupsd - the reason for those patches is the age of > the upses - roughly 10 years old+, which are can be a bit tricky to control. > From

Jean-Marc Valin skrev: > Ghost Wolf a ?crit : >> Hello Mailing List, >> I am a Speex supporter and user that would really like to know how much >> memory Speex uses to decode a 8kHz, 16kHz and 32kHz (primarily the 8kHz) >> and is it possible to use a 1kBytes of RAM to decode a 8kHz stream? (I >> was thinking of the possibility of using a ATmega168 to decode Speex)

Hello, since I had delayed the programming of the UPS Device part, now it is time to continue... My Device is "24 V DC modular ATX PSU" which replace the standard ATX Power Supply in PCs and use 15-43 V Input Voltage. The microcontroller is a TI LM3S5T36 Cortex M3 and I get the "UPS" infos using up to 4 Maxim DS1780 and some I?C current sensors. The ATX PSU has 4

For an unknown reason both my monitors ended up with a corrupted EDID. They both provide VGA and DVI input. The VGA input works fine, while DVI is broken because of the EDID issue. Using these [1] instructions I have been able to read the EDID and fix it. Unfortunately I'm not able to write it back to the eeprom. I always get this message: i2c i2c-1: sendbytes: NAK bailout. This is what I

My system configuration: ASUS M2A-VM motherboard AMD Athlon 64 X2 4200+ 2.2 GHz 4x A-DATA 1GB DDR2 800 memory 2x Intel 10/100/1000 Pro/1000 GT Desktop Network Adapter 2x Seagate Barracuda 250GB HD (RAID 1, software RAID) CentOS 5 x86_64; Kernel 2.6.23 (custom built); Version 7.6.9.2 e1000 driver The symptoms of this problem are outlined at: http://e1000.sourceforge.net/wiki/index.php/Issues[1]

On Fri, November 3, 2017 3:01 am, Sorin Srbu wrote: >> -----Original Message----- >> From: CentOS [mailto:centos-bounces at centos.org] On Behalf Of Valeri Galtsev >> Sent: den 2 november 2017 15:21 >> To: CentOS mailing list <centos at centos.org> >> Subject: Re: [CentOS] HP laptops with CentOS 7? >> On Thu, November 2, 2017 8:29 am, Sorin Srbu wrote:

On Mon, Mar 27, 2017 at 3:04 AM, Arnaud Quette <arnaud.quette at gmail.com> wrote: > as per confirmation from Eaton support team, and looking at the link above, > the latest FW is "02.12.0025". Hi Arno, According to that link, unless I'm missing something, as the 5P2200RT is a 2U sized unit (2 rack spaces) the proper firmware should be "03.00.0000". Firmware

On Dec 29, 2015, at 3:27 PM, Gene Heskett <gheskett at wdtv.com> wrote: > > Greetings Charles; > > I hope you had a nice Christmas, and will have a happy and prosperous new > year in 2016. Hi Gene, Thanks, and same to you! > You mentioned upsrw in a message earlier, so I ran it, and found the > shutdown timeout was only 20 seconds. > ... > So I tried to