similar to: RTP timeout if the asterisk box behind NAT

Hi; How can I know the duration that the DAHDI channel is still used? I need to know its status and since when it is in this status, how? Also, is it possible to hangup the channel if it has been openned more than 90 minute? Other than using the timeout in the Dial command (because this I know it). What is happening with me that from time to time, I find some DAHDI channels are stayed connected

Hi All; How to increase the waiting time between entering the digits for the analoge phone device that is connected to fxs? Is it by DigitTimeout? But how it will be apply for analoge station if the user just pickup the handset and dialed the number? Any help? Regards Bilal

Hi List; I heared that IAX is good for NATing issues, but I do not know if it can help me in that senario: I have two Asterisks machines in different sites and both are behind NAT (both have private IP address), I need to link these two asterisks with IAX trunk (if it help really in such senario), but I do not know if it will work without doing special routing settings on the router (like

Dears; It seems my service provider is requesting a complicated settings to allow me to send from behind NAT. What they said: "It shouldn't matter as long as you are handling the NAT correctly your end. We do not fix NAT so if you're sending internal addresses in your INVITEs or SDP then things will fail but if you're handling it correctly, we shouldn't tell the

Dears; I am facing the following problem: Already we requested from the service provider to enable the auto jumping service for our analoge telephone lines, so because we have 4 telephone lines from the service provider, then if you called line # 1 and it was busy, then the call will be sent to any available line #2 or #3 or #4, and if you call line # 3 and it was busy then the call will be sent

Hi List; If I am configuring Diguim Analoge card, then I need to run #modprobe wctdm, but the question why I need to run #modprobe zaptel also? What #modprobe zaptel does a things that #modprobe wctdm does not do? Any help? Regards Bilal ____________________________________________________________________________________ Looking for a deal? Find great prices on flights and hotels

Dears; I do not know if any had experience in using speex or ilbc with IAX and got good results, because I am facing a problem with GSM. I am facing a noise problem when I am using GSM with IAX trunk as following: IP Phone (G711) ---> Local Asterisk Box ---> IAX Trunk using GSM codec ---> Remote Asterisk Box ---> Digium Card (FXO) to terminate the call to the destination While no

Hi, Anyone here using sipgate.de ? It worked for months, but for a couple of days now I'm unable to register with them. My account is ok, because I can login to the website. Asterisk keeps showing me: Feb 25 23:50:18 NOTICE[5144]: chan_sip.c:5269 sip_reg_timeout: -- Registration for 'XXXXX@sipgate.de' timed out, trying again (Attempt #n) I looked at the sip debug stuff, and all I

Hello, For the moment I have the following settings in my sip.conf. I want to optimize them to archive the following things: - for the moment all my users will re-register too often. I want that only lagged users to re-register quickly. - check from time to time all users but no too often to see if is logged and can be called. Overall i want only lagged users to reregister and users with good

Hi, I am not sure if I am doing something wrong, but I can't get MeetMe to work with GSM codec (Asterisk 1.6.1 SVN r190371). My config files below: ---- sip.conf: ---- [general] context=common canreinvite=no bindport=5060 bindaddr=78.105.1.127 disallow=all allow=alaw allow=gsm rtptimeout=600 rtpholdtimeout=3600 rtpkeepalive=30 nat=no jbenable=yes tcpenable=no realm=dev-sip.wima.co.uk

Hi List; I need to do a call transfer using analoge phone connected to fxs, but I do not need this to be done using flash hook, let it to be using the # or * or any code, but how I can configure that this code is for transfer? Also, I do not need the flast hook to be used for trasfer as it cause usually a confusion to distinguish between the hangup and the call transfer. Any advise? Regards

Hi All; I succeeded to have a success call from Polycom behind NAT while Asterisk has public IP address, but I was not able to have a succeed call (it was established, but no voice running, and then the call disconnected) if Asterisk behind NAT and Polycom behind NAT. When Asterisk behind NAT and Polycom behind NAT, I forwarded the 5060 UDP to asterisk (at asterisk router) and to Polycom IP

Does the System() dialplan application have a limit on how long it can run? Either a time limit, or server load limit? I'm trying to pipe the output of Sphinx2 into Text2Wave, but Asterisk just runs by it to the next extension priority, with no errors. If I run the same command via the system shell, all is good, though it does take a few seconds, probably about 5 seconds to run. Yes,

Hello. I have an Asterisk server (ViciDialNow) set up behind NAT. I can manage to make outbound calls, but the communication drops off after 30 seconds or so. I'd really appreciate having some assistance from the mailing list on this issue. So, I'm having an Asterisk server behind a firewall and Zoiper softphones on SIP connecting to Asterisk on the same local area network. The

SetUp: - Asterisk behind a NAT, - Red Hat 9.0 - Asterisk 1.2.14 My Asterisk box is behind a NAT and I have a DiD from an ITSP. I have my dial plan set up so that when outside callers dial the DiD, the call is answered by my auto-attendant. The caller can then select who they'd like to speak to and the call is transferred to the external line associated with that person (usually a mobile

It seems that when setting qualify = 200 or qualify = yes in the database for a sip friend/peer, RealTime does not update the registration status like it should. I also have several peers which have been offline and Asterisk still reports them as registered, even though the registration seconds are only 200. Asterisk Ver: CVS HEAD 12/1/2004 Layout of sip_buddies: mysql> describe

Hi All; Can I run the IAX on TCP port instead of UDP port? If I ran IAX in TCP port, and in case my network was having a lot of users doing browse on the internet and downloading, so in that case and if the IAX used TCP port, so the voice will be better than using UDP (because in TCP the lost packets will be resend while in TCP it will not which will cause the voice to be cutting)? Same thing

Hi, Red Hat 9.0 Asterisk 1.2.7.1 Whenever I start Asterisk, I am unable to call out on my SIP channel: >-- Executing Dial("Zap/1-1", "SIP/6137451576@6477235412||t|") in new stack >Apr 30 11:02:00 WARNING[12814]: chan_sip.c:1973 create_addr: No such host: 6477235412 >Apr 30 11:02:01 NOTICE[12814]: app_dial.c:1029 dial_exec_full: Unable to create >channel of type

I have a couple asterisk boxes, running sip between both boxes. 1.4.43 on both. both are installed from source, both have default settings, My config for one box is: [devgeis] type=friend defaultname=devgeis username=devgeis secret=yes disallow=all allow=ulaw allow=alaw allow=gsm rtptimeout=60 rtpholdtimeout=60 rtpkeepalive=60 host=192.168.1.8 context=panel The other box is the same. There

Hello - I currently have 10 DID's coming into one Asterisk server, I seem to be having some difficulty routing based on the DID dialed and am hoping someone on the list can assist me. Here's the relevant info: Ingress SIP trunk: IP: 123.45.45.3456 DID's XXX-XXX-XX00-XX10 sip.conf: [general] useragent=Asterisk port=5060 context=default tos=lowdelay disallow=all allow=ulaw