similar to: Libvirt node is not getting booted through network with KVM too

Hi, I am trying to boot my node through network with the following configuration: But I am getting an error message saying: Even my network setting is not getting reflected in the Virtualbox. Can anyone suggest me what is wrong with this configuration. I think to boot a node from network we need to define a boot server but where shall I add that, I am confused.... Any help will be

Hi, Is it possible to attach a harddisk to an ESX node later after creating/defining it? If yes, can anyone tell me how to do it? Regards, Varun

Thanks a ton for the reply Matthias. I am little confused here. How to add volume on my esx server using virsh? I did SCP and copied my vmdk image to [datastore1] testNode/cluster.vmdk and also modified my xml file as you suggested. Now when I tried starting the node it gave me an error message saying: "error: Failed to start testNode error: internal error: Could not start domain:

Hi, I have started one node through libvirt API using its start method. I am trying to stop that node using the *destroy *method provided by the API but I am not able to do so. Instead, I am getting one message saying: *libvir: error: internal error Child process (vmrun -T player stop /root/test_folder/myImage.vmx soft) unexpected exit status 255* Can anybody tell me why I am not able to stop

So far I tested PXELINUX from 4.10-pre12, 4.10-pre9 and 4.10-pre6. The first two take a long time with a TFTP file not found and eventually find my file but error out (presumably to kaboom). The last takes a long time, does a lot of retransmitted packets (didn't watch the first two), then eventually loads the file but continues this behavior for TFTP and HTTP transfers. This is on VMware

Hi, Today I was trying to start a node using libvirt on ESX (esxi-5.1) hypervisor and I got the following error message: *virsh # define /local/myNode/esxdomain.xml* *Domain testNode defined from /local/myNode/esxdomain.xml* *virsh # start testNode* *error: Failed to start domain testNode* *error: internal error: Could not start domain: GenericVmConfigFault - Cannot open the disk

Hi, I was trying to add volume...I got one xml snippet and I modified it according to my node configuration: < volume> <name>testNode/cluster.vmdk </name> <allocation>0 </allocation> <capacity unit='G'>2<capacity> </volume> Now when I executed "virsh vol-create datastore1 /local/new_volume.xml" one error message came saying:

Hi, I am having issue while doing *ssh* to a virtual node through libvirt. The nodes's ip address is 192.168.82.1. When I am giving the command it is giving the following error message: *virsh# connect vbox+ssh://192.168.82.1/session* *Password:* *error: Failed to connect to the hypervisor* *error: End of ifle while reading data: sh: nc: command not found: Input/output error.* Can anyone

Hi, Im not able to boot my VM on esx hypervisor using libvirt. It says NO Operating System found. Can anyone help? Regards, Varun

Hi all, i am trying to create virtual box using libvirt , following is xml i tried to use following xml (followed example in libvirt site . http://libvirt.org/drvvbox.html) <domain type='vbox'> <name>vboxtest</name> <os> <type>hvm</type> <boot dev='hd'/> <boot dev='cdrom'/> </os>

hello,I 've deployed libvirt, and it is OK to use kvm.But when I use virtualbox,I can not attach a device to a domain. It reports the error that can't get device from device.xml here is my xml file for device(device.xml): <disk type='block'> <driver name='phy'/> <source dev="/home/lb/iscsitest/vdisk.img"/>

Hi Ján, Thanks a lot for the suggestion. It worked and volume is added to the datastore. Now if I try to start the node it gives an error saying: Error: internal error: Could not start domain: FileNotFound - File [datastore1] testNode/cluster.vmdk was not found." But .vmdk file exist at this location. What is going wrong here can anyobe plz suggest. Below is my xml: <domain

Hi, I was trying to connect to ESX server using libvirt's virsh console but I am getting the following error: *virsh# connect esx://172.16.73.14* *Enter username for 172.16.73.14 [root]: root* *Enter root's password for 172.16.73.14:* *error: Failed to connect to the hypervisor* *error: internal error curl_easy_perform() returned an error: Peer certificate cannot be authenticated with

Hi, I was trying to attach console to my virtual node created by xen but I am getting the following error: *varun:~# xm console xenDomain1* *xenconsole: Could not read tty from store: No such file or directory.* I have tried starting the xenconsoled service but still I am facing the same problem. Can anyone please help me out with this one? Regards, Varun

No it was not booted with xen kernel. Actually I tried booting it with xen kernel but I am getting a message saying Error No 15 : File not found. I tried editing the grub entry and noticed that there are 3 entries: 1) kernel /boot/xen.gz vga= mode-0x345 2) module /boot/vmlinuz-3.0.13-0.27-xen....... 3) module /boot/initrd-3.0.13-0.27-xen And in /boot i listed down the files, only xen.gz is there.

Thanks a ton for the reply Matthias. I tried your suggestion but now I got one more message saying: *virsh # connect esx://172.16.73.14/?no_verify=1* *Enter username for 172.16.73.14 [root]: root* *Enter root's password for 172.16.73.14: * *error: Failed to connect to the hypervisor* *error: internal error: curl_easy_perform() returned an error: Unsupported protocol (1) : Protocol https not

Hi, I am trying to install xen and provide libvrit support to it but while installing at some point of time it tries to connect to GIT repository and creates a clone but I am behind firewall and it is getting timed out.... :( I am pasting a screenshot below. Can anyone of you please help me out with this one. // Varun

Hi, I am trying to attach a usb device to my virtualbox node using libvirt. My node is already running, I stop my node and then I am trying to add this usb device. I have a separate xml file defined for usb. It looks like this: *<device> <hostdev mode='subsystem' type='usb'> <source> <vendor id='0x4321'/> <product

My objective is also to run headless virtual machines through libvirt library. I am using an Ubuntu 10.04 distro and libvirt 0.9.2. Before asking you guys about it, I searched on the web and found this: Hi, > > thanks for your hint. > > I read the lines in the documentation, but unfortunately editing the xml > > within virsh lead to the errors. > > The Solution to a

Thank you so much for the reply... :) I am trying to build this on OpenSUSE-11.4. And you said that I can get distro provided packages. I just want to ask whether installing those packages will work? Where can I get those packages? Can you please provide the link. I am scared of playing with the kernel as I am doing these things on a server that is why I am asking these things. // Varun On