similar to: PRI (Primary-NTT)

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out the DS1's, we are trying to setup the system with 2 dchannels for each 4 DS1's. Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv but when I asterisk asterisk it says: Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is reserved for D-channel. Aug 10 16:33:32 ERROR[8954]:

hi folks. recently some of our customers complained about bad voice quality on the phone system. i looked at the logs and found a lot of these: [2012-11-03 08:26:38] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:45] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:54] NOTICE[11305]

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Hi! I have a E1 PRI connected to my TE400P card on span 1, and two channelbanks on span 3 and 4 and * 1.2. Every few hours I get this message and asterisk dies just after that: Warning: No D-channels available! Using Primary on channel 16 anyway! When this happens restarting zaptel and asterisk services, generally puts the system back online my zaptel.con reads: span=1,1,0,ccs,hdb3

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it

Out of the blue i started receiving the following error on my PRI line which connects my asterisk server to a Norstar 0x32 key system. The asterisk zaptel.conf file was configure as follows and this config worked for 6 months until friday. Nothing was changed on either system prior to friday. here is teh zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

We've been working for the past 2 weeks to get a new V400P working with our PRIs from the telephone company. We're trying to get the Asterisk server setup as a VoIP gateway for SIP and AIX. We can make SIP-SIP calls, but all calls from or to the PRI fail. This is the applicable entries from the Asterisk log (configuration files follow) for a call coming from the PSTN on the PRI. I

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2 I've got a 2 port T2XXP card attached with on T1 currently plugged in. Inbound calls work fine, but outbound fail with the rather cryptic: [May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) There are similar threads I've found on the

My TE411p does not seem to like to have two PRIs from different telcos (span 1 and span 2). I can get one working, but not the other. However, if I use vpmsupport=0 when loading the wct4xxp module, they both work. But here is the problem, vpmsupport=0 disables the on board echo cancellation. Any ideas? BTW, here is zaptel.conf span=1,1,0,esf,b8zs span=2,2,0,esf,b8zs bchan=1-23 dchan=24

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

Did you compile and install libpri *before* Asterisk? I had same problem (among others) b/c I didn't install in the correct order. Try the awesome asterisk_update.sh shell script. Are you trying to emulate CPE or NET? Try signalling=pri_cpe Check for whitespace behind the statement, zapata.conf seems bitchy about whitespace. hth -----Original Message----- From: Steve Totaro

We are currently working to trunk from a Nortel 81C to an Asterisk Server 1.4 running on Red Hat Linux. We have two PRI trunks which work with the exception of the clock slips, which is causing the Nortel to reset the PRIs once a hour. Thanks for any suggestions. 81C MSDL Asterisk Digium TE110P REQ prt TYPE adan dch 10

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

Any ideas? 51] logger.c: [chan_zap.so] => (Zapata Telephony) Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata-auto.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing

Hello. New to the list. We're in the process of deploying Asterisk. Actually, we're going live tomorrow, and I just found out that my Zaptel cards have been mis-configured. I'll preface this by saying that I have looked in the wiki, read through the samples, and attempted to call Digium (they're closed.) So I'm praying that someone on the list can help me out! I have two