similar to: Multiple Code-book Setup

Hi All, Sorry if this is too much silly. Vorbis encoder gives out packets of information. 1. Is it that each packet contain information of one frame/window either 256 / 2048 or any length set by encoder? If yes then the encoded packet will be variable in length. 2. Every packet is divided into segments, how does the encoder decide on number of segments in each packet? It must be dependent upon

Hi, If this is true: "Granule Position Information in Ogg Header is a hint for the decoder and gives some timing and position information." So say if granule position is 10000, it means that 10000 PCM samples are encoded in this page approximately. If this is true we can neglect this information, it will not effect the decoding right(but might effect for streaming)? Ravi

Hi, Can any one explain me basic concept of Floor Generation in Vorbis encoder? Ravi __________________________________________________________ Yahoo! India Matrimony: Find your partner online. Go to http://yahoo.shaadi.com

hi everyone, here i have a question: is there any chance in llvm intermediate representation to compare whether a operand (ie a value) is used as a user without iterating over all the instructions in a basic block. i will explain this with an example: i=p+4; j=i+p; in the above example i mean p,4,i,p which are on the RHS are operands and the terms i,j which are on the LHS are users. so what i

Hi, I am using Samba 3.0.7. on a Red Hat 9 system. I tried to configure the machine as a PDC by using a configuration file quite similar to what is giving in the chapter 4.Windows NT domains of 'Using Samba' 2nd edition by Orielly. Using testparm shows that the machine has been identified as a PDC of the domain 'hamsateam.' To test the PDC, I tried to make a WinXP

Sir, Given code like: > > X = add int Y, 1 > Z = mul int X, 17 while I iterate over the operands of the first instruction i want to print the variable x ,as well as the constant 1 and while i iterate over the second instruction i want to print variable x and constant 17. what should I do? thanking you, yours sincerely, anubham suresh TU-Darmstadt --- llvmdev-request at

On Wed, 2006-02-15 at 04:29, anubham suresh wrote: > hi everyone, > here i have a question: > is there any chance in llvm intermediate > representation to compare whether a operand (ie a > value) is used as a user without iterating over all > the instructions in a basic block. > i will explain this with an example: > i=p+4; > j=i+p; > > in the above example i

hello everybody, here I have a question regarding printing of the constants( like 2 .63 etc.,) present in the instruction while iterating over the instructions within a basic block . I am able to print the vaiables but not the constants. Can you please tell me how to get the constants printed out while iterating over the instructions because the constants do not have names as the variables do(

Sir, I am using LLVM Compiler for my Maters Dissertation work. So I want to include one chapter on LLVM in my report. Can I copy some of the figures from your documentation which is available on the net and keep them in my work ? thanking you, yours sincerely, Suresh Anubham TU-Darmstadt Germany Anubham Suresh Measurement and Instrumentation Electrical Department IIT Roorkee Current

hi all, I can not get voicemail working in realtime with asterisk-1.2.6. extconfig.conf is correct voicemail => odbc,asterisk,voicemail_users i am getting the fallowing error Executing Answer("SIP/xx.xx.xx.xxx-0a02e1c0", "") in new stack -- Executing Set("SIP/xx.xx.xxx-0a02e1c0", "foo=102") in new stack -- Executing

Hi All, Can any one link me or send me a complete detailed spec of Vorbis encoder? I found the Vorbis_I_spec.pdf but it does not provide much information about encoding procedure. Ravi -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.xiph.org/pipermail/vorbis/attachments/20050829/cf209e5a/attachment.html

Hi Running racoon on a Freebsd-4.11 machine gives a kernel panic. I am using the racoon from ports directory which comes with the freebsd installation. Steps followed are as shown below: racoon -f /usr/local/etc/racoon/raccon.conf setkey -f ipsec.conf ping -c 1 <ip_of_the_other_gw> The ping will lead into a crash. The crash dump looks like for th ping packet it

hello sir, i want to control the bandwidth when sending traffic between two logicial address (ip address ) on the same interface (eth0) on the same machine. can i do it using tc tool. i am sending mail using sendmail between 2 users on same machine and sniffing packets at receiving side. but i want to control bandwidth of this traffic so that i do not lose packets at capture.

Hi, I am running the dbt2 test kit for postgres-8.0.1.The driver and client are running on Sun Solaris 10 and the database is running on Red Hat 9.I am running the test kit for 100 warehouses with tpw(terminal per warehouse) value of 80. I did truss on driver and found that after executing some transactions an error comes related to EPROTONOSUP. The particular point where error comes looks like

Hi All, Is it possible to Call an external number For X minutes if first attempt resulted In Busy or No Answer? i.e, for example, if I called 335 8698, and it was busy, or may be said it was busy, Asterisk will try calling back that number for 15 minutes, once every 5 minutes. Thanks Jibu ________________________________________________________________________ Yahoo! India Matrimony: Find your

Hi, I need an immediate help from anyone of you. Does asterisk support call waiting in SIP phones? Thanks for advance Jibu ________________________________________________________________________ Yahoo! India Matrimony: Find your life partner online Go to: http://yahoo.shaadi.com/india-matrimony

hello list, i have problem when i am useing wrapuptime with agents.conf my agents.conf looks like this [agents] autologoff=15 musiconhold => default wrapuptime=50000 group=1 agent => 1001,4321,Mark Spencer recordagentcalls=yes my aim is every call needs have wrapuptime of 5000 ms but when ever a call comes its directly connecting not wating any more. your views will be highly

I am using samba-3.0.7 on kernel version 2.6.5-3 (client as well as server). I traced the exact function calling sequence when a "mkdir" command is given at the client side. I got stuck at the server side, source/smbd/vfs.c - vfs_MkDir() - SMB_VFS_MKDIR(conn,name,mode) (line no 357) Could anyone please tell me exactly where is the vfs_ops struct initialised, and which function will

hello list , my set up is like this ip device -->ser ---> asterisk(astcc) --> pstn gatewsy my asterisk version is 1.0.2 iam using the ser as registration and asterisk aa the prepaid one with the help of the astcc. now my problem is the destination people i.e the pstn line s are listening low voice and also the blurr sound quality along with the audio of the ip device at

We have made some changes in samba-3.0.7, as part of our graduation project. Are there any test suites which we could use to check the conformance of the changes, with the original samba specifications? Also, with reference to your statement in document tridge_cifs04_tutorial.pdf , saying that inputs about test documents would be welcome, if the above mentioned suites are not available,then we