similar to: IAX2 over OpenVPN connection.... working but

Hello, I want to create a VPN between two Asterisk servers using OpenVPN. How to configure Asterisk and OpenVPN to do that. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070809/ddaed76b/attachment.htm

Hello All, I have installed Asterisk 1.6 with openVPN in the same machine. I have set up a VPN connection between 2 SIP clients and Asterisk using x-lite. The 2 clients connects to Asterisk. SIP signaling goes ok over the vpn tunnel. When attempting to make a call between the clients, the siganling part of the call goes well. But, when the call is set up, some RTP packets are exchanged at

I am looking at terminating a OpenVPN tunnel on my shorewall box, but selectivly forward incoming traffic from the VPN tunnel to various hosts on my LOC-zone. Is this doable? Or need I set up OpenVPN tunnels that terminates on the LOC-hosts in question directly? (Or rather: Which page on the web site have I neglected to read _this_ time?) Happy new year to one and all! .

Hello I read a whole book on OpenVPN, but still can't figure how to configure the server + client so that the the client connects and sends SIP/RTP data through the tunnel. To get started, I'd rather use a shared key instead of X509 (certificates + keys). The server is running on a uClinux appliance, with /dev/net/tun, and OpenVPN is 2.0.9. The clients will be Windows hosts connecting

I am trying to setup openVPN 2.0 beta11 (sever/client configuration) and shorewall. I managed to get it working with out shorewall in the mix. When I start shorewall this message appears in the logs. Oct 12 13:41:03 localhost kernel: Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:04:5a:7f:92:9f:00:b0:c2:89:68:e4:08:00 SRC=69.145.71.133 DST=216.187.138.18 LEN=42 TOS=0x00 PREC=0x00 TTL=46 ID=11 DF

Hi, I had some performance problems with TINC running on Windows XP. I had a VPN tunnel running over a wireless network to a Linux VPN server. Web browsing through the tunnel was a pain. Big web pages with lots of pictures loaded very slow compared to a plain network connection. When the VPN client was running on a Linux computer, and a Windows computer was browsing the web through the VPN

While I have concentrated on support for 2.6 native IPSEC in release 2.2.0, I am still of the opinion that unless you absolutely need IPSEC compatibility that OpenVPN is a much easier (and in the case of roadwarriors, a much better) solution. Having already generated all of the required X.509 certificates, it took me less than 1/2 hr to replace my IPSEC testbed with an OpenVPN one using the new

Hi, I am new to VPN an OpenVPN with shorewal. I tryed a lot and read a bounch of howto''s but nothing helped so I came here. I want to tunnel all request to my server 141.48.XXX.XXX from my home network throu port 443. I want to do this because this is the only way I can connect to my server using ssh or ony other tool or port. On Port 80 Apache is running, so I only have the https port

Greetings, I want to setup bandwidth restrictions for a few clients that use openvpn to connect to my server. I''m using iptables to mark the packets in the mangle table (PRE/POSTROUTING) on eth0 before they get sent via the tunnel. Will the mark survive even if the packets then get routed via an openvpn tunnel (tunX) out the box or does openvpn change it removing the mark ? damnit,

Perhaps someone with a sharper brain than I can solve this little mystery. I've Googled until I'm blue in the face, read all TFM's I can find, and tried several iptables rule combinations but just can't get the following to work. Here's my challenge: I have a CentOS-5.3 "main" server with a static public IP address running Apache, OpenVPN, and a bunch of other

Good day, First off, I''m a complete puppet newbie, this openvpn recipe is pretty much the first puppet work I''ve done so be gentle :-) Secondly, the openvpn setup for Debian (and systems based on Debian) allows each openvpn network (tunnel) to be specified using a separate config file for each: /etc/openvpn/<vpn>.conf Each tunnel can be then stopped/started/restarted

> I don't think it's an endpoint issue. I think the SIP packet headers get > over-written by the tunnel (openvpn) protocol. I'd be rather astonished if OpenVPN itself were responsible for this. As far as I know, OpenVPN doesn't do higher-level-protocol rewriting of any sort. It just provides the "bit pipe" through the tunnel. I'd suggest several other

Hi Everyone, For some reason a few phones connected to a pfSense box can't make or allow in OpenVPN in port 1194 UDP. So, I established the VPN tunnel on 1194 TCP and it works fine. I would like to know if there is any disadvantages to using TCP over UDP for the tunnel when using Asterisk or is just as reliable and solid as a UDP tunnel? Thanks -------------- next part -------------- An HTML

Hi all, I have set up a working OpenVPN2 connection between my Server and my gateway at home. Now I want all traffic to be routed through this VPN connection. Currently everything is going through eth1 to the internet (to the gateway of the University which forwards it to the internet :-). We must use a prox-server and because of this I am not abel to watch the real-Media streams on

Hello List, I tried to set up openvpn with the shorewall on my openwrt box but failed! I am not able to access the "loc"al Network from my vpn. I followed the roadwarrior setup. I define a vpn zone, that should be able to access the firewall and the local network: vpn fw ACCEPT info fw loc ACCEPT info vpn

Hello, I have the following situation : Server with 2 nics 1 nics connected to the internet, 1 connected to the LAN I have OpenVPN running on the system and the following setting in the tunnels file : =================================== openvpn:2000 net 62.58.0.226 openvpn:2001 net 62.58.0.226 openvpn:2002 net 62.58.0.226 =================================== All tunnels ran for weeks

I''m new to openvpn and maybe I should be asking on openvpn''s list... But I read the tutorial: http://www.shorewall.net/OPENVPN.html#id2452626 and saw the following: " On System A: ifconfig 192.168.99.1 192.168.99.2 " I don''t understand the reason for using these "virual" IPs. For instance, I configured openvpn on my peers so that the IPs on the

Hi Everyone, I have setup an OpenVPN tunnel between Server A (running Asterisk) and Server B suppling it's SIP Phones with DHCP pool of IPs. So, the tunnel is established nicely and everyone can ping others. "sip show peers" shows the local subnet of the SIP Phones registered (192.168.100.0/24 ). But there is the old bad one-way audio. Calls also drop after few seconds. In the SIP