similar to: centos 6.3 live-cd no internet connection

good day, I am new to centos. Using a standalone laptop. Downloaded and burned the live cd. All seem ok except screen resolution only 800x600. Most importand I do not seem to find the install to hard disk option anywhere. Some distros I tried do have an option to install on the screen when you are happy about the OS. Googled but could not find the howto for the live cd install. Kindly

Good day, Been googling about this matter. Afraid I am now confused. Too many options..: for/against/whatever. Some is years ago. Kindly please a step x step manner in which to accomplish to enable mp3 please. Thanks Johan

Good day, Gparted is not available on my installation. Which patition tool is available in centos 5.5 please. Thanks Johan

Good day, What can I expect if I should install a server version of a distro on my laptop, please. Thanks Johan

Good day, > [johan at unknown2a6800000000 ~]$ How/where could I make the above a lot shorter please. Thanks Johan

Good day, Some yum instructions I do not know. Kindly some pointers please. There are unfinished transactions remaining. You might consider running yum-complete-transaction first to finish them. The program yum-complete-transaction is found in the yum-utils package. This is where I am lost Thanks Johan

Good day, By accident booted with dsl internet not connected. When reconnecting dsl - centos did not detect it. Is there a way to make it trigger detection rather then rebooting Please. Thanks Regards Johan

Good day, Please, How/where can I add an application to start at boot up. Don't seem to find it in options available Thanks Johan

good day, I have tried to install mplayer according to instructions from the following sites..: http://wiki.centos.org/AdditionalResources/Repositories/RPMForge http://wiki.centos.org/TipsAndTricks/MultimediaOnCentOS Then last..: [root at johan ~]# yum install libdvdcss libdvdread libdvdplay libdvdnav lsdvd mplayerplug-in mplayer mplayer-gui compat-libstdc++-33 flash-plugin

Good day, New to centos, New install . Using - Software updater While updating - downloading 73 updates there was a break in the download. The break happened close to the end. Now when using software updater again will it start all over again? Go on where the break happened? Could not find on google this issue Kindly some advice please. Thanks, Regards Johan

Good day, I would like to first test and then use centos 5.5. I downloaded centos 5.5 x86_64 live CD. Problem...screen resolution only 800x600. In fedora 14 it is 1024x768, same in debian squeeze and opensuse11.3. Could there be a way to increase the resolution? in either i386 or x86_64. Thanks Regards Johan

I am using a Netgear MA401 with the wi driver, and am having trouble using wpa_supplicant to set static WEP keys. I have the wlan_wep.ko module loaded with wlan and wi built into the kernel. My wpa_supplicant.conf looks like this: ctrl_interface=/var/run/wpa_supplicant ctrl_interface_group=wheel network={ ssid="INTERNERD" scan_ssid=1 priority=1 key_mgmt=NONE

I rebuilt my notebook that has the atheros card in it, and forgot to save all of my setup to get it working. I am using dkms and the madwifi rpms from rpmforge. My modprobe.conf has a line: alias wifi0 ath_pci I can ifconfig wifi0 up But the command: /usr/sbin/wpa_supplicant wpa_supplicant -dd -D madwifi -i wifi0 -c /etc/wpa_supplicant/wpa_supplicant.conf fails. Now some of my old

Hi, I am running Centos 4.1 on a Dell D610 with ipw2200. Any good howto for running wpa-psk? I have searched and not found much related to RHEL or CentOS. -- Thanks http://www.911networks.com

Hi Folks, I'd like to install my USB-WLAN-Stick Netgear WG111v3. Ndiswrapper works correct after installing Kernel-Modules from atrpm ndiswrapper-kmdl-2.6.18-53.1.19.el5.centos.plus-1.52-16.el5.i686.rpm. But by calling wpa_supplicant with wpa_supplicant -i wlan0 -D wext -c /etc/wpa_supplicant/wpa_supplicant.conf -d machine freezes. My wpa_supplicant.conf:

hi all, this is my first hit on the mailing list. hope i m posting in the right place. well, i have a dell vostro 1510 laptop with broadcom wifi adapter. n it doesnt work! :( i installed the wifi drivers with ndiswrapper. iwconfig shows the following. [root at laptop ~]# iwconfig lo no wireless extensions. eth0 no wireless extensions. sit0 no wireless extensions. wlan0

I seem to be able to lock my machine by going into wpa_cli and asking it to 'reassoc'. The reason for question mark after "hard" is that debug information (caused by wlandebug and athdebug) is being printed on the console. The only way to get machine's attention is to hold power button for 8 seconds. Note: manual reassociation is just the handy way to reproduce the problem

Hi, Running: Freebsd 6.0 I am wondering if it is possible to have acces to loopback ip in a jail. I currently have a server running a jail. In the jail, there is a database and a web server. I would like to be able to have the database only bind on a loopback address and not on the jail's ip. Can this be done and how? Thanks -Cyril

first, the short form of the question -- has anyone got that wireless adapter working on centos 5.5 and associated with an access point that uses WPA/WPA2 security? and the details. in a classroom where there is *no* wired networking at all, all PCs have only that wireless net adapter, which works fine on windows but, after installing centos 5.5, unsurprisingly, we have no networking. there

Hello and good day, i have setup a Server which is directly connected to the Internet, without NAT-Router or other Firewall Appliance. I am using FreeBSD 6.2. I have pf enabled to only allow traffic on specified Ports. I am using Apache-13 + Postfix + Dovecot & mysql for my Mail-system. There is only one /home/User, which authenticates via a Key with Pass- phrase to sshd. The