similar to: PRI got event HDLC Abort

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Hi, On a Asterisk 1.8.12 system working OK for months (>100k calls proceed), users are complaining for bad audio. My setup is: PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI ---> PSTN asterisk -rx "dahdi show version" DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC asterisk -rx "pri show version" libpri version: 1.4.12 A

Hello I've got small PBX (30 simultaneous connections) based on asterisk (1.6.2.6), which uses Stargate 2N ISDN to GSM gate. It runs ok for day or two, but then I get: dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16) in my kernel logs, in asterisk i get: pri show spans PRI span 1/0: Provisioned, Down, Active PRI span 3/0: Provisioned, In Alarm, Down, Active (span 3

Hi, I have a client that has a 24 channel voice T1 that I have been using e&m signalling over for a number of years. The local telco finally got an ISDN switch and wants to move them to PRI. I didn't see this as a big problem - I've done a few others on this particular Caribbean island without issues, but this would be the first time with a Xorcom unit involved. We tried to do

We are using AAH with Asterisk 1.2.7.1 with a TE405P as listed below. We are getting frequent restarts on the spans which lead to dropped calls. I have pasted some hopefully pertinent information below -- anyone have any clues that might help? Thanks Next line is repeated throughout messages, going through every channel in every connected span. asterisk/full.1:Apr 24 01:15:25 VERBOSE[4196]

Hi All, I am facing problem with E1 line. I have installed Asterisk (1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10) But every now and then I face problem of down E1's. The log show lot of entries like "pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2" This happens on a regular basis and the E1 becomes up after some time. My

Hi, I'm getting the following error from an asterisk 1.6.0.9 installation: [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: Asked to delete sched id -1??? [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: No more room in scheduler This repeats a few times, then asterisk crashes. I can't seem to locate any info on this error at all. I'm using

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Hi, Running 1.4.26.1 here. I have installed TE420B card in my server, and followed the appropriate steps (as far as I know to configure it). This TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling type. When I dial out, I get this message: Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0

Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the

> -----Original Message----- > From: linux-pci-owner at vger.kernel.org [mailto:linux-pci-owner at vger.kernel.org] > On Behalf Of Yijing Wang > Sent: Saturday, July 26, 2014 8:39 AM > To: linux-kernel at vger.kernel.org > Cc: Xinwei Hu; Wuyun; Bjorn Helgaas; linux-pci at vger.kernel.org; > Paul.Mundt at huawei.com; James E.J. Bottomley; Marc Zyngier; linux-arm- > kernel at

> -----Original Message----- > From: linux-pci-owner at vger.kernel.org [mailto:linux-pci-owner at vger.kernel.org] > On Behalf Of Yijing Wang > Sent: Saturday, July 26, 2014 8:39 AM > To: linux-kernel at vger.kernel.org > Cc: Xinwei Hu; Wuyun; Bjorn Helgaas; linux-pci at vger.kernel.org; > Paul.Mundt at huawei.com; James E.J. Bottomley; Marc Zyngier; linux-arm- > kernel at

Dear All, we have installed a TE410P card on a Dell Poweredge 1750 running a slackware 10 with 2.4.26 Kernel. Then we have made two loops on the card and we have configurated all the 120 channels. Our goals was to perform some stess tests even if in this scenario we used the same box as generator and target. The stress test comprised to generate up to 60 calls at the same time by placing a file

I just managed to put in a TE410 card in an Asterisk box to work with OnRamp 20(E1 downunder). I am able to dial in but was not able to dial out. Can anyone offer me some advice please? In my extensions.conf, I just put in: [default] ... exten => 0,1,Dial(Zap/g1) and I get this on the console when I dialled 0. -- Executing [0 at default:1] Dial("SIP/5166-b76004f8",

Hi, I am about to pull my hair out after trying to get our PRI up and working. We are switching from a Cisco gateway to an Asterisk box which provides the 23 phone lines for our office. So, because the Cisco gateway is working I can assume I have all the settings right (b8zs, esf, dms100, etc) and the PRI is live (because we are switching over). When dialing from PSTN, I get busy signal. When

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

I need to know how to setup the data side of the T1 on my Linux Box. I have found information about configuring a PRI and HDLC but nothing about the Frame-Relay type setup for data. The following is information from our T1 provider. Network T1: Framing = ESF Line code = B8ZS Build out = 0-133ft(DSX)/0dB(CSU) Clock = network Pulse-density-enforce = off alarm-option = on alarm-delay = 15

Hi fellow asterisk users, I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel module) an approx. 100 snom320. The whole installation is running without issues since 5 months. Without having changed anything on the asterisk server for at least 2 months, i noticed "clicking sounds" at external calls over the PRI. Asterisk constantly throws the following messages: ...

hi! I'm trying to get zapras working in GSM csd network. Whenever a dialup call is initiated from the mobile to the * gateway the following appears in the log and zapras terminates. Phone gives the error dialup not answered. ==> /var/log/messages <== pppd[2310]: Plugin zaptel.so loaded. pppd[2310]: Zaptel Plugin Initialized pppd[2310]: Using zaptel device 'stdin' pppd[2310]:

All, I'm having a heck of a time getting hdlc to work on kernel 2.6.11.9 .. I compiled hdlc, hdlc_gen, hdlc_cisco, hdlc_raw, into the kernel (note into, and not 'modules'). System comes up, I configured zaptel.conf span=1,0,0,esf,b8zs nethdlc=1-24 modprobe wct4xxp ztcfg sethdlc hdlc0 cisco ifconfig hdlc0 up All of this works fine, believe it or not. I have a T1 cross plugged