similar to: Linux Software RAID 1 - Unequal Sized Hard Disks

Hello, On the Intel Core 2 Duo processor based systems, we have the option of installing either x86_64 or the i386 distribution. I would like to know your experiences with the x86_64 port. How does it compare with the i386 distribution in terms of stability, reliability and performance ? How significant are the performance benefits gained by using the x86_64 linux instead of i386 on the same

I have a doubt. If you use such a script monitoring the link status with ping and then reconfiguring, why do you need the DGD patch? You need to do some reconfiguration (change multipath to a single default route) anyway if you use the script, right? Also, the DGD patch uses src to lookup the routing table entry, but if you have a dynamic IP for the WAN interface (PPPoE, DHCP etc), this approach

Hello! I read the Split access and Load balancing sections into LARTC (Chapter 4). However I have one gateway only and the LARTC says about 2 links. I need to know how to make a load balance with my links. Thanks in advance. Eriberto - Brazil

Hello, Does CentOS 5.4 support large ( > 2 TB) external storage devices using GPT (GUID Partition Tables), while the main OS resides on smaller hard disks using MBR. In this scenario, what can be the largest possible size of an ext3 partition (and filesystem) which can be created on the storage array under CentOS 5.4 ? Thanks, Manish

I have recently installed CentOS 6 on a system with a Realtek 8180L wireless card. The wireless card is detected properly and uses the rtl8180 driver. But it connects to our wireless network only after logging to the Desktop Environment (GNOME) and using the Network Manager Applet. In order to make the wireless card connect to the network automatically at system start up, I edited the Connection

Hello, Is there any command / option available on CentOS to expire a user's password immediately ? I remember using "passwd -e" on some other distribution but the -e option does not seem to be present on CentOS 5.x. Thanks, Manish

Hello all! I applied http://www.ssi.bg/~ja/routes-2.6.8-10.diff patch to kernel 2.6.8.1 and it works fine, or almost fine. It does the load balancing well, but when one link is dropped it continues to try it. At the end of http://www.ssi.bg/~ja/nano.txt it is said to ping gateway 1 and gateway 2, for the kernel to know if that route is working, but since my linux is connected to the links

Hi all! After that good thread "DGD patch not detecting dead gateway" I was able to set up a Load Balancing with ping based DGD (without Julian Anastasov patch). But now I''m facing a new problem and tried some options, with only partial solutions. I made a script based on http://www.mail-archive.com/lartc@mailman.ds9a.nl/msg16257.html (Thank you Manish Kathuria),

hello i have slackware installed and i have two internet connections , ADSL(2,5mbps) + CableModem(1mbps) i want to share the connections in a small network NAT for the ADSL connection, and a proxy server for the cablemodem connection i searched all over the internet (probably not where i was supposed to) but i could''n find a solution if someone could give me a tip i would really

I got file conflicts between the sysreport and sos packages on the file /usr/sbin/sysreport. I unchecked sysreport in the package updater UI and the rest of the update is proceedng.

Hi I need informmation about this Topic: Load balancing,, I have 2 nic to internet, 1 nic to DMZ, and 1 nic to LAN, but I don,t know how do that. Where I can found information ?? Thx!! For your information! -- Este mensaje ha sido analizado por MailScanner en busca de virus y otros contenidos peligrosos, y se considera que est? limpio. For all your IT

Hello, I have configured a load balancing router using Julian''s patches and as described in "nano.txt" for two ISP links as shown below. ISP 1 ISP 2 . . | | | | | | | WAN

Hi, A friend of mine has 2 lines of 512kbps terminated in two Linux boxes. He now want to remove those 2 boxes and have some device which will loadbalance the two ISPs and also have a failover arrangement. But he has agreed to give me a chance to do it on Linux for my own satisfication. Is this easy to do with lartc? How do I go about it exactly? I have very less time to do it since his

I want to configure a device with three network interfaces where two of them would bridge two segments of the LAN subnet and the third one would be connected to the WAN link. eth0 - 10.10.10.2/24 to be connected to the internet gateway having IP 10.10.10.1/24 (also the default gateway for the device) eth1 and eth2 bridged as br0 with IP address 172.16.100.1 connected to different segments of the

Dear Sir, Please help me in building the right solution. My requirement is: 1st I want to club both ISP bandwidth to get 512kbps. 2nd, In normal condition, it should be in Load balancing. 3rd , In ISP Failover condition, traffic will automatically route to working ISP. What I have: I have installed the RHEL 3.0 with 3 Network Card. Kernel is 2.4.21-9EL I have the link from two ISP both

How are the updated kernels released by Red Hat / Cent OS related to the latest vanilla kernels ? Are the changes, new features and drivers, etc. available in the newer kernels also ported to the updated kernels released by Red Hat in their entirety ? For the lifetime of a distribution like RHEL 4 or RHEL 5, Red Hat would stick to the same major and minor number of the kernel and would just

hi all, first i wann to explain my network & it''s problem, i am using a redhat el5 for multigateway routing, i have 3 adsl lines which is connected with eth0, eth2 and eth3. eth1 is my local network. those 3 lines comes with adsl modem from same isp with equal bandwidth (512 Kbps). In this adsl modems there is one lan and one wan port, adsl modem''s lan ip is gateway for my

Hello, This is on Centos 6 and not something I think is wrong with Centos 6 but I am looking to see if anybody else has experienced this and if there is solution. So thanks up front for indulging me. Because Linux makes routing decisions before SNAT it is causing problems when trying to use FTP with two upstream providers in a load balanced setup. Other than ftp, things seem to work OK. Below

Hello, I would like to use nas4free under xcp 1.6. I install it under full HVM using "other install media". Now I am attaching 4 hdds as external disks. The vm sees at most two hdds, I suppose because of bios support (1 boot + 1 cdrom + 2 hdds= 4 hdds). I need to use more disks, is it possible? If not, it seems to me a serious limit. Mario

I am facing problems assigning the owner and group to an ext3 filesystem being mounted from an external storage. I created a mount point /vol and changed its owner and group to alpha and beta respectively (as required). The ext3 filesystem (LV from the external storage) was then mounted on /vol using the mount command. However, after mounting the filesystem the owner and group of /vol changed