similar to: Automatic jump from line to line for incoming calls and the problem in DAHDI

I'm not sure if this is an Asterisk thing, a handset thing or a telco thing, so please be gentle with me if this is not the right place to ask ..... When placing a call over a SIP channel to a mobile phone, if the phone is engaged, it does not return a BUSY status straightaway. Rather, I get a ringing-out tone for the timeout duration specified in the Dial() statement; *then* I get

Hi, Long story short - I have an ancient Britsh Telecom phone attached to my Asterisk PBX via Dahdi. It works beautifully, receiving calls, and the call quality is excellent. However, dialling out is impossible, as Asterisk consistently mis-reads the number of pulses the dial sends (it could be a squiffy dial, I'm not sure). Not to mention the fact that, in today's modern "want

Hi All; To overcome the echo problem, what mainly I have to do in the configuration other than the following line in the system.conf under dahdi directory? echocanceller=mg2,1-16 1) How can I know if the digium card supporting echo cancellator? 2) If I am getting a message in the consol that unable to enable the echo cancelator, then what does it means? The hardware is not supporting echo

Hi; How can I know the duration that the DAHDI channel is still used? I need to know its status and since when it is in this status, how? Also, is it possible to hangup the channel if it has been openned more than 90 minute? Other than using the timeout in the Dial command (because this I know it). What is happening with me that from time to time, I find some DAHDI channels are stayed connected

Hi All; I have an E1 card with two ports for ISDN PRI. Do I need to install DAHDI in addition to LIBPRI? For placing outside calls (outgoing) via the PRI, then in the extension.exe file, I will use the Dial function? But how can I determine that I need to use the PRI channels and not the analoge channels? Last point: how can I know that asterisk is containing libpri? In other words, how can I

Hi I have a 3 level nested while-endwhile loop in a macro that when the execution reaches endwhile, it is jumping out to the While at the caller macro. It shouldn't since the are instructions after the endwhile. -- Executing [s at macro-call-from-outside:72] EndWhile("DAHDI/i1/1234567-4a7f", "") in new stack == Channel 'DAHDI/i1/1234567-4a7f' jumping out of

Hi All; Asterisk version is 1.6.1.8 Dahdi version is: dahdi-linux-complete-2.2.0.2+2.2.0 Since long time, and I am facing this problem and I did all the trouble shooting that I know without any success. The problem that while we are talking with someone through the FXO (connected to the PSTN analoge line), suddenly the call disconnect (without any specific time). I tried callprogress=no and

Hi All; To download, compile and install DAHDI, do I need to download the both (dahdi-kernel and dahdi-tools) If yes, then do I need to do the compilation and installation command for each package? What is the method to download, compile and install the both packages as one package? By the way: Why there is dahdi-kernel and dahdi-tools? In other words, for what the kernel is used and for what

Hello; I am installing asterisk and dahdi on ubuntu "and I used my username bghayad to login for ubuntu and do the installation, actually I feel my problem is related to the?username and permission but I am not able how to fix it", I am facing now mainly the following two problems: The first one, asterisk is not starting automatically although I did sudo make config (for asterisk and

Hi All; How to let the virualbox (ubuntu OS) to be able to see the digium card? Because when I install elastix or asterisk with dahdi, it is not able to see the digium card if the installation though the virualbox .. What is the solution? Regards Bilal

Dear; Thanks a lot for guiding me. Is it possible that the installation libpri-1.4.11.5 newer than the libpri-1.4.11.5-patch? Well, when I typed (note: I am trying to apply the libpri-1.4.11.5-patch for the libpri-1.4.11.5): libpri-1.4.11.5# patch -p0 -i libpri-1.4.11.5-patch It gave me that patched detected as shown below (example of one file, and I got same for other files): patching file

Dears; To patch libpri: I just place the patch file in the libpri source directory and then I run make and make install? Or I need to compile the dahdi and asterisk also? If the problem stayed, do I have to go for previous libpri version? Or for previous dahdi version and asterisk version? Regards Bilal ----------- > bilal ghayyad wrote: > > But I am afraid it is a bug because I

I am having an issue with a couple of phones where they ring, but there is a long delay after the phone is picked up before the audio starts. My setup: * Server running Asterisk 13.9.1, Dahdi 2.11.1 w/ OSLEC * Server is CentOS 7 * Quad core CPU with 16GB Ram * 2 Snom 300 phones. * NO NAT. Server and phone are on the same subnet with only a gigabit switch between them. * Digium

Hi All; In dahdi: what we use instead of ztcfg -vv (that is existed /sbin/ztcfg -vv). ? Regards Bilal

Hello, I am missing any description of zaptel/DAHDI alarms. The TE200 series user manual contains only a description of LEDs states. These alarms states are visible in zttool/dahditool or in astersick CLI (zap show status) and I wonder what is the real meaning of these alarms for E1 channel. Possible alarm states (based on zaptel.h 1.2): 1. No alarms 2. Recovering from alarm 3. In loopback

Dear All; I am afraid from IRQ misses: 1 The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP. The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)? [root at CC

Hi All; If I need to set the opermode to King Saudi Arabia, what the name I have to use? For example, to set it for kuwait then I use opermode=KUWAIT. So what will be for Saudi Arabia? Any advise? Regards Bilal

Hi All; When the call coming via the E1 dahdi and I handle the call (as first step) by exten => 5631040,1,Goto(OrangeCMG,s,1) it is not working and the call will be disconnected instead of queued. But, when I handle the call (as first step) by playing any sound file and then send for the queue, then it is working fine, WHY? exten => 5631040,1,Playback(WelcomeMessage) exten =>

Dears; The problem was related to something else. The Digium card has two PRI ports, actually to get it UP, I have to configure the two ports and both of those two ports to take the timing from span 1. Why this, I do not know ! Although I am using only one E1 connected to span 1, so why I have to configure the other span !! After configuring the second span, so now one D channel for span 1 is

Hi All; My ISDN was working fine, and suddenly I start getting the below: sig_pri.c:985 pri_find_dchan: Span 1: No D-chanannel anyway! There is a Yellow Alarm, so what it could be the problem? My configuration as following: system.conf span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 chan_dahi.conf context=IncomingPSTN group=0 signalling=pri_cpe switchtype=euroisdn