similar to: uncoerce.... to get real number instead of integer?

I have a rather unusual setup within which I'd like to run samba. At this point I have: a) 3 networks (all private IP's) b) net1, net2 are interconnected by a router. net1 has a host that also acts as a WINS server and is local master, domain master, preferred master for it's group. (linux slack7.0, samba 2.0.5) router between net1, net2 has an IP in each network and samba

Hello, I am working on Network-Simulation (VNUML). Our simulator uses linux bridgi= ng to connect the UMLs. So there is one problem: The example is the following: There are two hosts simulating one big net. The two hosts have connection over the external nets Net3 and Net6 (see htt= p://www.uni-koblenz.de/~timbub/verteilteSim3.GIF), but in fact there is onl= y one physical connection between the

Hi, CONFIGURATION: the important part of my setup looks like that (smb.conf): [global] interfaces = net1 net2 net3 net4 net0 ; this is a router which acts as cross-subnet domain master + wins ; server local master = yes preferred master = yes domain master = yes wins support = yes dns proxy = no os level = 99 net1 - net4 are Win95, WinNT, Linux net0 are two samba-1.9.18p1 fileservers

Hi, i get this error when i run the net command to mapp unix group to nt groups. [root@samba smbldap-tools]# net3 groupmap add ntgroup=?Domain Admins? unixgroup=?Domain Admins? rid=512 Bad option: Admins? [root@samba smbldap-tools]# and also when i try to list the current groups in the domain, i get this error but i can see all entries if i use gq [root@samba smbldap-tools]# net3 groupmap

Relevant part of "net3 groupmap list" is System Operators (S-1-5-21-1617713866-2789119093-1479812082-1007) -> sys In howto there is the following example net groupmap modify ntgroup="System Operators" unixgroup=sys net groupmap modify ntgroup="Power Users" unixgroup=sys You can add System Operators but trying to add Power Users fails. If you do it in reverse

I have a router with 3 network interfaces like in the following ASCII diagram below. All interfaces are 100mbit. There is tcp traffic being sent from net1 to net3 and from net2 to net3 and the tcp connections consume as much bandwidth as possible. There is a pfifo queue on the egress interface eth0 of the core router with a limit of 10 packets. net1 --> (eth1) router (eth0) -> net3

Hi all, I need my servers to decide which network they are in (i.e. dmz), and the only clue is the servers IP-address. I was trying to accomplish it like this, but it doesn''t work: case $ipaddress { "10.1.1.*": { $network = "net1" } "10.2.2.*.*": { $network = "net2" } "10.3.3.*": {

Hello I have a 2.2.7a samba server on linux 2.4 some users complain about mutual locking on a share user A and user B access share S on the server as disk S: A and B both use the same app which creates workfiles/tempfiles on S (actually the app drives ms-word throught ole to format and print reports) A's workfile is named temp1fusionAAAA.doc and B's one is temp1fusionBBBB.doc and they

Hi, and thanks in advance for your support (sorry my english) Is there any documentation for migrating Samba 2.2 with LDAP and PDC suport to Samba3 with PDC and LDAPSAM? I try to explain the situation: Only one server running Mandrake 9.2 + Samba 2.2.8a with ldap support (from precompiled contrib); and I wish to migrate to Samba3+LDAPSAM. My real problem is that I must use ldap because I also use

Hello, I''m trying to setup an 8 port wan configuration (pptp+pppoe) with one vlan trunk. My internal networks are : LAN(eth9): 10.0.0.0/16 VLAN10(eth9) 10.10.0.0/24 VLAN20(eth9) 10.20.0.0/24 VLAN30(eth9) 10.30.0.0/24 VLAN100(eth9) 10.100.0.0/24 I would like to post my configuration here since i don''t success to do the following: 1. Communicate between VLANxx to LAN

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

Its been a few days, I was wondering if anyone else has any ideas on how to get this to work? If not, could I ask a the direct question as to if anyone here has (or knows someone who has) successfully got something like a Cisco Router to successfully establish an ISDN data/Internet connection through the Asterisk PBX?

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

I installed the RPMS from samba web site for Mandrake 9.1. Configuration is weird as things are labeled smbd3 or winbind3... Testparm runs against /etc/samba/smb.conf yet swat configures the smb.conf in a different location...hmm.... But really my problem is joining the AD domain as a member server. I can't locate the net tool. How is this done? How does testparm know to test against

Hi I decided after some testing and experimenting, to move the production servers from 2.2.x to 3.0. so I've installed samba3.0 in paralel with the old binaries. To start the migration I wanted to save the old domain SID, to can make the migration as transparent as possible, so I did: net3 -d 10 -I 127.0.0.1 getlocalsid while the old binaries are still runing all that I've got

Hi I thought I finally had this PDC pu and runing but I don?t. Samba is working fine ?cos I can see the shares from other machines (I?m yet to join them to the domain). I have a mandrake 9.2 and using samba 3.0 and ldap 2.1.22 as backend and not able to join machines to the domain so I used ldapsearch and net groupmap to see what?s up with the ldap server and it came up with the following

RC 1 is now available for testing. This version corrects several problems in Beta 3: 1) Release notes now correctly refer to FORWARD_CLEAR_MARK rather than CLEAR_FORWARD_MARK. 2) The NET3 column in /etc/shorewall/netmap now works correctly. 3) A missing closing quote in the generated script when using REQUIRE_INTERFACE=Yes has been corrected. 4) The compiler now correctly detects the

RC 1 is now available for testing. This version corrects several problems in Beta 3: 1) Release notes now correctly refer to FORWARD_CLEAR_MARK rather than CLEAR_FORWARD_MARK. 2) The NET3 column in /etc/shorewall/netmap now works correctly. 3) A missing closing quote in the generated script when using REQUIRE_INTERFACE=Yes has been corrected. 4) The compiler now correctly detects the

We own an Asterisk box with the following configuration: Linux Debian 4.0 Kernel 2.6.18 Asterisk 1.2.23 Zaptel 1.2.19 We installed a Digium B410P card, and we are using 3 ports in te_ptp mode (it is connected to BRI adapters on Italian ISDN lines, provided by Telecom Italia; in Cisco language, they should be "isdn switch-type basic-net3"). Configuration strictly complies the

Hi there I use a winmodem wich is apache a56sp-hcf and Windows 98 how Can l start dial ?up connection with wine best regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://www.winehq.org/pipermail/wine-users/attachments/20011127/bf822bde/attachment.htm