similar to: SSD caching of MDT

I am trying to build lustre-1.6.6 against the pre-patched kernel downloaded from SUN. But as written in Operations manual, it creates rpms for 2.6.18-92.1.10.el5_lustrecustom. Is there a way to ask it not to append custom as extraversion. Running kernel is 2.6.18-92.1.10.el5_lustre.1.6.6smp. -- Regards-- Rishi Pathak National PARAM Supercomputing Facility Center for Development of Advanced

For future filesystem compatibility, we are wondering if there are any Lustre MDT filesystems in existence that have 2B or more total inodes? This is fairly unlikely, because it would require an MDT filesystem that is > 8TB in size (which isn''t even supported yet) and/or has been formatted with specific options to increase the total number of inodes. This can be checked with

For future filesystem compatibility, we are wondering if there are any Lustre MDT filesystems in existence that have 2B or more total inodes? This is fairly unlikely, because it would require an MDT filesystem that is > 8TB in size (which isn''t even supported yet) and/or has been formatted with specific options to increase the total number of inodes. This can be checked with

Hi, Our lustre environment is: 2.6.9-55.0.9.EL_lustre.1.6.3smp I would like to change recovery timeout from default value 250s to something longer I tried example from manual: set_timeout <secs> Sets the timeout (obd_timeout) for a server to wait before failing recovery. We performed that experiment on our test lustre installation with one OST. storage02 is our OSS [root at

Hi, The documentation warns about using smaller inodes than 512 bytes on the MDT. If I plan to use a stripecount of one (I have many small files), is it possible to use an inode size of 256 bytes and still use in-inode EAs for metadata ? Thanks /Jakob

Greetings Group! I hope this will be an easy one. To conserve steps in backing up the metadata extended attributes of a Lustre mdt, I am looking at using a newer version of tar combined with its --xattrs option. (Note: Previously I have used the mdt two-step back-up from the Lustre Manual and it has been successful.) If I can backup the extended attributes via tar so that I don''t

on our cluster that has been running lustre for about 1 month. I have 1 MDT/MGS and 1 OSS with 2 OST''s. Our cluster uses all Gige and has about 608 nodes 1854 cores. We have allot of jobs that die, and/or go into high IO wait, strace shows processes stuck in fstat(). The big problem is (i think) I would like some feedback on it that of these 608 nodes 209 of them have in dmesg

Just checking to be sure this isn''t a known bug or problem. I couldn''t find a bz for this, but it would appear that tunefs.lustre --print fails on a lustre mdt or ost device if mounted with mmp. Is this expected behavior? TIA mds1-gps:~ # tunefs.lustre --print /dev/mapper/mdt1 checking for existing Lustre data: not found tunefs.lustre FATAL: Device /dev/mapper/mdt1 has not

Dear all, Two of our MDS have got repeatedly read-only error recently after once e2fsck on lustre 1.8.5. After the MDT mounted for a while, the kernel will reports errors like: Oct 8 20:16:44 mainmds kernel: LDISKFS-fs error (device cciss!c0d1): ldiskfs_ext_check_inode: bad header/extent in inode #50736178: invalid magic - magic 0, entries 0, max 0(0), depth 0(0) Oct 8 20:16:44 mainmds

Hello, We have running lustre 1.8.1 and have met "No space lest on device" error when uploading 500 Gb small files (less then 100 Kb each). The problem seems to depends on the number of files. If we remove one file, we can create one new file, even with Gb size; but if we haven''t remove something we can''t create even very little file, as an example using touch

Chris, Perhaps you need to perform some write_conf like command. I''m not sure if this is needed in 1.6 or not. Shane ----- Original Message ----- From: lustre-discuss-bounces at lists.lustre.org <lustre-discuss-bounces at lists.lustre.org> To: lustre-discuss <lustre-discuss at lists.lustre.org> Sent: Fri Mar 07 12:03:17 2008 Subject: Re: [Lustre-discuss] Multihomed

I installed 1 MDS , 2 OSS/OST and 2 Lustre Client. My MDS shows: [code] [root at MDS ~]# lctl list_nids 10.94.214.185 at tcp [root at MDS ~]# [/code] On Lustre Client1: [code] [root at lustreclient1 lustre]# lfs df -h UUID bytes Used Available Use% Mounted on lustre-MDT0000_UUID 4.5G 274.3M 3.9G 6% /mnt/lustre[MDT:0] lustre-OST0000_UUID

OK, so our old MDS had hardware issues so I configured a new MGS / MDS on a VM (this is a backup lustre filesystem and I wanted to separate the MGS / MDS from OSS of the previous), and then did this: For example: mount -t ldiskfs /dev/old /mnt/ost_old mount -t ldiskfs /dev/new /mnt/ost_new rsync -aSv /mnt/ost_old/ /mnt/ost_new # note trailing slash on ost_old/ If you are unable to connect both

I installed 1 MDS , 2 OSS/OST and 2 Lustre Client. My MDS shows: [code] [root at MDS ~]# lctl list_nids 10.94.214.185 at tcp [root at MDS ~]# [/code] On Lustre Client1: [code] [root at lustreclient1 lustre]# lfs df -h UUID bytes Used Available Use% Mounted on lustre-MDT0000_UUID 4.5G 274.3M 3.9G 6% /mnt/lustre[MDT:0]

Hello, When I run a "df -i" in my clients I get 95% indes used or 5% inodes free: Filesystem Inodes IUsed IFree IUse% Mounted on lustre-mds-01:lustre-mds-02:/cetafs 22200087 20949839 1250248 95% /mnt/data But if I run lfs df -i i get: UUID Inodes IUsed IFree I

Hi all, I''m getting my feet wet in the infiniband lake and of course I run into some problems. It would seem I got the compilation part of sles11 kernel 2.6.27 + Lustre 1.8.3 + ofed 1.4.2 right, because it allows me to see and use the infiniband fabric, and because ko2iblnd loads without any complaints. In /etc/modprobe.d/lustre (this is a Debian system, hence this subdir of

Hi all, Here is the situation: I have 2 nodes MDS1 , MDS2 (10.0.0.22 , 10.0.0.23) I wish to use as failover MGS, active/active MDT with zfs. I have a jbod shelf with 12 disks, seen by both nodes as das (the shelf has 2 sas ports, connected to a sas hba on each node), and I am using lustre 2.4 on centos 6.4 x64 I have created 3 zfs pools: 1. mgs: # zpool

Hi, We run four-node Lustre 2.3, and I needed to both change hardware under MGS/MDS and reassign an OSS ip. Just the same, I added a brand new 10GE network to the system, which was the reason for MDS hardware change. I ran tunefs.lustre --writeconf as per chapter 14.4 in Lustre Manual, and everything mounts fine. Log regeneration apparently works, since it seems to do something, but

We have been struggling with our Lustre performance for some time now especially with large directories. I recently did some informal benchmarking (on a live system so I know results are not scientifically valid) and noticed a huge drop in performance of reads(stat operations) past 20k files in a single directory. I''m using bonnie++, disabling IO testing (-s 0) and just creating, reading,

Hi I want my lustre do such things during OST failed: if some file has stripe data on th failed OST, any operation on the file will return IO error without blocking, and also at this moment I can create and read/write new file or read/write files which have no stripe data on the failed OST without blocking. What should I do ? How to configure? thanks! swin -------------- next part