similar to: How to install ovirt in working environment?

This lays 90% of the groundwork needed on the server side to support the use of a remote ipa server. Leaving the option disabled in the installer until the necessary node integration(dns/keytab placementi location) is completed Also apply: [PATCH server] update ovirt-add-host to use ipa commands instead of kadmin.local [PATCH server] separate ipa common tasks freeipa::common and rename

Updates the installer to handle the scenario in which the guest and admin networks are the same by using an alternative httpd conf. Verified to work (eg oVirt managed vms are bootable) on the oVirt appliance so far. --- conf/ovirt-server.conf | 88 -------------------- installer/bin/ovirt-installer | 11 +--

This completes the last few requirements for remote ipa, one thing to note is that when using remote ipa we do not allow the choice of creating a local dns server on the ovirt node. --- installer/bin/ovirt-installer | 22 ++++++++++++++++--- .../modules/ovirt/files/ovirt-remote-ipa.conf | 1 + installer/modules/ovirt/manifests/freeipa.pp | 10 +++++++++

This set the cobbler modules dns/dhcp to dnsmasq, removes a duplicate ip replacement in /etc/cobbler/settings, and sets the ip address to the admin network instead of the guest networkwhere it should've been in the first place. --- installer/modules/ovirt/files/modules.conf | 4 ++-- installer/modules/ovirt/manifests/cobbler.pp | 16 ++++------------ 2 files changed, 6 insertions(+),

Hello all, I was told on IRC that I should come here to discuss a recommended change on the networking page in the wiki. If you take a look at the "Basic Script" shown here: http://wiki.libvirt.org/page/Networking#Forwarding_Incoming_Connections It does two things: 1) Create a DNAT rule in the NAT table of IPTABLES 2) Create a FORWARD rule in the FILTER table of IPTABLES The FORWARD

On 06/08/2015 02:43 PM, Laine Stump wrote: >> However, if I changed the destination address from "anywhere" to the >> IP of the host machine, the problem resolved. So I change the script >> to as follows. (Changes are highlighted. For some reason the original >> script didn't work using /bin/sh, but it did with /bin/bash, so I >> changed that too). >

Signed-off-by: Joey Boggs <jboggs at redhat.com> --- installer/modules/ovirt/manifests/freeipa.pp | 8 ++++---- installer/modules/ovirt/manifests/postgres.pp | 12 ++++++------ 2 files changed, 10 insertions(+), 10 deletions(-) diff --git a/installer/modules/ovirt/manifests/freeipa.pp b/installer/modules/ovirt/manifests/freeipa.pp index e5de852..f91cd43 100644 ---

Hi I''m trying to use the Typo wordpress converter script, but it requires that the wordpress database is accessible over the connection to the Typo database. To get around this, I''m trying to use ActiveRecord::establish_connection (...) to get a connection object to run the raw SQL queries that Typo''s wordpress converter uses on. It doesn''t work with Ruby

This clarifies the dns setup section in the installer and notifies to use the bundled dns setup if the management server is not in the upstream dns already --- installer/bin/ovirt-installer | 2 ++ 1 files changed, 2 insertions(+), 0 deletions(-) diff --git a/installer/bin/ovirt-installer b/installer/bin/ovirt-installer index 2d88886..862c5e2 100755 --- a/installer/bin/ovirt-installer +++

From: ??????? <pronix.service at gmail.com> if krb5kdc has worked before installation appear error. and require 'ipactl restart' --- installer/modules/ovirt/manifests/freeipa.pp | 5 +++++ 1 files changed, 5 insertions(+), 0 deletions(-) diff --git a/installer/modules/ovirt/manifests/freeipa.pp b/installer/modules/ovirt/manifests/freeipa.pp index aa806fe..5a9fb44 100644 ---

Hi list, i'm have a problem..i'm setup two domain controller with different subnet..my client login into domain with network mapping drive Subnet #1 : 10.1.0.0/16 Subnet #2 : 192.168.21.0/24 PDC 1 : 10.1.1.7/16 PDC 2 : 192.168.21.3/24 If i'm ping, traceroute or ssh from each client it's successfull but i can't see the network neigborhood at each domain, if i'm login from

Hello, I''m used to using Xen in a bridge mode where my dom0 and all domUs are on the same layer 2 network. However now I have to set up a server whose eth0 is on one network and the domUs will be on another /29. So, for example, if the eth0 of dom0 is 192.168.1.214/24, then I have 10.1.1.0/29 (10.1.1.0 -> 10.1.1.7) routed to it for use in domUs, how would I go about setting that up?

I''m trying to execute an ldap modify command but have run into issues with multiple lines and can''t seem to find a happy medium. Any ideas ? exec {"ipa_modify_username_length": command => "/usr/bin/ldapmodify -h $host_name -p 389 - Y GSSAPI <<LDAP dn: cn=ipaConfig,cn=etc,dc=example,dc=com

I just wondered whether anyone actually got this working and produced a how-to ? I recently had a customer ask about embedding it into their web pages for there customers to call them with ?? To be honest I have no idea how etc.... Gary .

So should I go ahead and make the changes to the script that I suggested? Thanks, BJ On Mon, Jun 8, 2015 at 3:21 PM, Eric Blake <eblake@redhat.com> wrote: > On 06/08/2015 02:43 PM, Laine Stump wrote: > >> However, if I changed the destination address from "anywhere" to the > >> IP of the host machine, the problem resolved. So I change the script >

Hi all, My NT environment cannot recognize my SAMBA servers(Bad IP address when ping from MS DOS prompt) and after I restarted the nmbd daemon it can see my SAMBA servers. Does anyone know why this happens? Is it there is a change in the WINS server's database? Please advise. thanks & regards, Bridget

For many months I've been trying to replace a Samba 3.0 Domain Controller with a version that will support Windows 7. Despite advice on Samba HOWTO that all supported versions will support Windows 7 there seems to be an unstated caveat, namely that it must be configured as an Active Directory Domain Controller. Microsoft's own advice is that Windows 7 will not work with a Windows NT

Hello, please guys, any help will be appreciated. I have two linux servers (samba-3.0.2-6.3E) with RHEL 3E: Server one: Configured as logon server (network inside) The other server: with the user's accounts. (network dmz) The error message in "one": [root@linux root]# smbstatus -b Server's Role (logon server) conflicts with server-level security The "other" server

I was hoping someone can help with a problem with my GrandStream Budgetone "hanging" after a while. Problem seems related to the SIP registration - I am using dynamic registration (host=dynamic in sip.conf). Static IP is not an option in my case. I start Asterisk and all is groovy, phone works fine and can dial around. Then, at the time specified on the phone in the "Register