similar to: node servers show as unavailable after reboot of management server

Hi, I builded ovirt from next ... installed ... node is booted from pxe. After reboot of ovirt-server machine is node unavailable(enabled). According to jguiditta's advice I restarted libvirt-qpid on node and node becomes available. Is there a bug? Thanks for help. Jan Mrozek

After running for a while the node becomes "unavailable" in the server UI. All VMs running on that node also become unavailable. The node is still running fine as are all the VMs, they're just no longer manageable. I looked on the node and everything appeared to be running fine. Looked on the server and ovirt-taskomatic was stopped (this seems to happen quite a bit).

I did a yum update on my management server and now the ovirt gui is no longer accessable. Is it supposed to just work or do I need to do something after the yum update? Justin.

If I ssh to a vm running Centos and then execute "poweroff" from within the vm, the vm shuts down as expected but the host in the admin ui becomes unavailable. Is anyone else experiencing this? I haven't checked to see if other guest OS's do the same thing yet. The painful thing is that then I have to shutdown all the VMs and reboot both the host and the management server

The VMs just boot up with the default network interface model which is 100Mb, is there a way to set it to a 1Gb model? Cheers, Justin.

Hi, I have set up a 40GB iscsi target on my san and when I add it in to the storage pool and it shows up as 40GB. When I try to create a 40GB volume in the ovirt UI it tries to but fails. The error message is that the volume will not fit. If I create one smaller than 40GB it works. Is anyone else experiencing this? Also, if I then start a virtual machine up to install on the newly

This patchset removes ovirt-identify-node and ovirt-listen awake. It adds startup script support for the matahari qmf agent, which takes over the responsibility for communicating node hardware capabilities to the ovirt-server. On the server side, host-browser has had its node identification functionality replaced by a new script, host-register, which is what interfaces with the matahari qmf agent

Hi, I'm having some problems building ovirt. The build fails during the final ovirt build stage in the instructions. The failure is because it can't find "/usr/share/ovirt-node-tools/ovirt-node-recipe.ks". I've checked and sure enough it's not there. Has anyone else come across this problem? Building on FC13 using the instructions found here:

----- "Justin Clacherty" <justin at redfish-group.com> wrote: > > I ran ipa-server-install from the command line and the error it's > getting is this: > > Traceback (most recent call last): > File "/usr/sbin/ipa-server-install", line 41, in <module> > import ipaserver.krbinstance > File

--- ovirt-node.spec.in | 3 ++- 1 files changed, 2 insertions(+), 1 deletions(-) diff --git a/ovirt-node.spec.in b/ovirt-node.spec.in index 746cf3d..2fdf4f5 100644 --- a/ovirt-node.spec.in +++ b/ovirt-node.spec.in @@ -21,7 +21,7 @@ Requires(post): /sbin/chkconfig Requires(preun): /sbin/chkconfig BuildRequires: libvirt-devel >= 0.5.1 BuildRequires: dbus-devel hal-devel -Requires:

The purpose of this patch is to add support for the matahari qmf agent package (http://git.et.redhat.com/?p=matahari.git;a=summary) to the node. The following actions are taken: 1. Deprecate ovirt-identify-node and ovirt-listen-awake by removing them from the autotools scripts, the rpm spec and the node startup scripts. 2. Remove ovirt-listen-awake and ovirt-identify-node completely. 3. Add

Greetings Everyone, I have a question here regarding the ovirt node during boot. I have configured ovirt-server with all the procedures followed from wiki and finished each successfully. Also i tried booting one of the nodes with ovirt-node image through PXE boot. The machine which i booted got an dhcp IP (hostname) and was listed in the ovirt web gui. But there is a issue i have been seeing

Are the build instructions out of date? I've been following them but when I get to "make update-app" I get make: *** No rule to make target `update-app'. Stop. I took a look in the Makefile and sure enough there's no updated-app target or update-host for that matter... What's the procedure now? Cheers, Justin.

Hi all, I've got some problems to make work oVirt. I've installed a Fedora 10 VM the lightest possible (nothing checked, even based) and installed after some packages (wget, sudo, acpid,...) and updated the system. By the way, acpid should be a dependency of ovirt-installer because the installation fails if it's not available. I've then installed ovirt (ovirt-server-installer

Hello I found on ovirt.org instruction for set unavailable(enable) to available(enable) i run "ruby /usr/share/ovirt-server/qmf-libvirt-example.rb" and get Error caching credentials; attempting to continue... Connecting to amqp://main.forex-24h.com:5672.. /usr/lib/ruby/site_ruby/1.8/qpid/delegates.rb:209:in `connection_start'/usr/lib/ruby/site_ruby/1.8/qpid/delegates.rb:209:

It's not 600M in order to accomodate new RPMs. Signed-off-by: Darryl L. Pierce <dpierce at redhat.com> --- common-install.ks | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-) diff --git a/common-install.ks b/common-install.ks index a20a5b4..2a7fbb7 100644 --- a/common-install.ks +++ b/common-install.ks @@ -4,7 +4,7 @@ timezone --utc UTC auth --useshadow --enablemd5 selinux

The original bug report is filed here: http://issues.apache.org/jira/browse/QPID-1973 The svn revision 975209 and onwards for qpid contains the fix. --- src/host-browser/host-register.rb | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-) diff --git a/src/host-browser/host-register.rb b/src/host-browser/host-register.rb index 57c11b7..06d8553 100755 ---

On the network theme again. The adapters on the management/storage network all default to an mtu of 1500. Are there plans to be able to indicate when a network supports jumbo frames? Cheers, Justin.

I did post to ovirt-devel but I am not a registered user, so a moderator need to review my posting before it becomes available. I will register, but right now I only have a few seconds to spare. I try to add use "Add Virtual Machine" but the "Storage" is empty. My iSCSI and NFS storage says "State: pending_setup". What am I doing wrong? Sincerely, /bs66

Hi. I have successfully installed ovirt. Boot 2 nodex throught PXE boot, and added to pool. Whe i try to create NFS storage, they in state: pending setup. How to add NFS storage? taskomatic.log INFO Wed Sep 30 16:59:09 +0300 2009 (1991) starting task_refresh_pool INFO Wed Sep 30 16:59:09 +0300 2009 (1991) storage_find_suitable_host: host node3.ovirt.priv uuid 30303234-3144-3832-4638-3931FF