similar to: Size of x11 device

I originally set up this monitor with an analogue lead. Everything seemed fine, so I didn't check xorg.conf at all. Then I bought a digital lead, and since then the monitor blinks. Running system-config-display identifies it as a 1280 x 1084 CRT monitor. It is an LCD monitor. That model is not on the drop-down list, so assuming that a specific driver wasn't available for it, I

I have had my "nv" driver lock up a number of times. I downloaded the "nvidia" drivers and they did not work at 1920x1080 resolution. I am looking for an updated driver for just "nv". I found some once for a different driver that you just update commonXXX and yourdriverXXX not the whole X recompile. Where can I find those drivers? THanks, Jerry --------------

Hi all, Up until today everything has been fine with CentOS on my Toshiba laptop. I booted into CentOS 4.3 today and Kudzu detected my video card for some reason. I let it configure it (wish I hadn't now). I can still get in. X and Gnome work. But the video resolution is 800x640. The LCD is capable of 1024x768. I cannot change it using Gnome tools or direct editing of

I just put a 1680x1050 LCD monitor on my home system, and I went into system-config-display to configure it as such, and it just won't take. I had to tweak some of the settings by hand, but when I log out, I get the wide screen for both the Nvidia driver splash screen and the login screen. But, when I log in, It jumps back to 1280x1024 and refuses to run in wide screen mode. Here's the

Hi, I just got a new Samsung 226bw 22" wide monitor to replace my previous one. I also have a nvidia 8600gts video card. I can set interactively [through the nvidia-settings utility] the 1680 by 1050 resolution. I have saved the settings in the xorg.conf, but I can't keep it after a restart of X or a reboot. When I restart X, the login is at: 1680 by 1050, then it switches to 1280 by

In the vein of the "Can't get resolution higher than 1280x1024" and "Another CentOS 5 oddity..." threads, I just installed CentOS5 w/Xen kernel on a Sony VAIO desktop with an nVidia NV5M64 (RIVA TNT2 64 Pro) card, using an old Samsung SyncMaster 700NF monitor. system-config-display chose the highest possible resolution for the monitor and Xorg did its best to drive it, but

My OQO has a VIA chipset. From the hwconf: class: VIDEO bus: PCI detached: 0 desc: "VIA Technologies, Inc. CX700M2 UniChrome PRO II Graphics" vendorId: 1106 deviceId: 3157 subVendorId: 1106 subDeviceId: 3157 pciType: 1 pcidom: 0 pcibus: 1 pcidev: 0 pcifn: 0 When I install Centos, I default to the vesa driver, and it operates at the monitor's native 800x480. Of course I

Hi, Did anyone manage to get 4.4 working on a Dell D620 laptop? The thing has a 1440x900 LCD screen, but I don't get X the work with that resolution. (lspci: Intel Corporation Mobile 945GM/GMS/940GML Express Integrated Graphics Controller (rev 03)) Google suggested to use '915resolution', which I installed (915resolution-0.5.2-1.el4.rf), but that doesn't help. Regards, --

Ryan wrote: > I did, 1024x768. > Sorry, analog Matthew Miller wrote: > Maybe the problem is just in that adjustment, then. Yes. You need to have your signaling _exact_ when dealing with LCDs. Some are very good at taking the timings of VESA standards. But some support some eccentric Windows timings that are _not_ the exact same as VESA. Or maybe you have configured your monitor for

Hello, I am having problems with video in X. I get an over frequency issue using the stock CentOS 4.2 driver. I have searched IBM and Intel for the driver but no luck. Occassionally I see something about need to load a kernel module for agpgart. How do I do this? Anyone have a similar setup or know where I can find the driver? TIA

Dear All, I have managed perfectly fine to install centos 5.5 x64 on a new sun blade x6270 server module .i had to install in text mode since GUI install mode was not working Actually this machine is going to replace my current working very low hardware server the server is used as my primary dns, mail server , webmail server also running Mailscanner, mailwatch etc. Also I want to use

I have an i810 chipset and am trying to set a custom mode. X is not taking that mode. Has anyone else run into this situation? How do I get X to take the mode on an i810 driver. Jerry

First of all, I am sorry for my bad english. I have a UC-LoGIC WP8060 tablet.I using wizardpen taplet driver. I using PS 7.0 with wine-0.9.33. My Pen worked perfectly with wine-0.9.33, but PS7.0 has some bugs. I update my wine "wine-0.9.56". PS 7.0 working perfectly but my pen has not got pressure sensitive. I turn back wine-0.9.33. I have too much problems PS 7.0. I want to use new

I have a Centos 5.7 machine with Intel I10 video (built-in, I guess -- this is one of those all-in-one mini terminal things) that I'm trying to put a new 1920x1080 monitor onto, without conspicuous success. Prior to this it's been using a smaller monitor with no issues. Try as I might I can't get the new monitor to run at its 1920x1080 resolution. I just realized that I forgot to

I am the tech guy for a local library. We have a network containing several diskless workstations. The hardware are these P4 boxes: http://www.geeks.com/details.asp?invtid=SAMBA845V-24-4-R&cat=SYS (We have inserted additional memory, bringing most of the machines up to 1.25Gig of memory, and two up to 2Gig of memory.) These little machines have integrated Intel video chips on their

I am attempting to setup a dell inspirons 1200 laptop media accelerator 900 from intel is the chipset so I am using the i810 driver. In the default 1024x768 everything is fine. I am trying to setup the external port not the LCD to be 1366x768. I added a modeline to xorg.conf of: Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor"

If I use "system-config-display" or "system-config-display --reconfig" although I get a message that I need to log out of GNOME, to have the new file written, for new Display Resolution, logging out or restarting the box does not result in the new settings for the Display taking hold. Sometimes, the number of colors is updated, but *never* the Resolution. Below is my xorg.conf

My xorg.conf foo is pretty weak today. Does anyone have an ATI 4250 in a dual head config? I'd be interested in looking over your xorg.conf. Sean p.s. Mine at the moment, that doesn't work very well: http://people.freebsd.org/~sbruno/4250_xorg_conf.txt

hello! i am using archlinux x86_64. i have got a 32bit chroot and also 32bit libs installed, so i can run 32bit apps inside the chroot or using the libs. now my problem: my native desktop resolution is 1680x1050. i want to play my games in 800x600, 1024x768 or whatever. when i run a game in the chroot, it works like a charme, wine changes the resolution and i have no problems at all. when i run

WoW detects my monitor hz as 77, 78, 79. 80, 81, 82 but not 60hz which it should be! This causes a lot of tearing which can be annoying. Is there any way of fixing this?