similar to: kernel-2.6.9-55.0.12.EL not booting (lvm? 3ware?)

Here are the version numbers I get after installing the 9.2.1.1 release: Model 9500S-4LP Firmware FE9X 2.08.00.003 Driver 2.26.03.019fw BIOS BE9X 2.03.01.052 Boot Loader BL9X 2.02.00.001 A bit confusing. I thought I saw a map of code set releases to various version numbers but I couldn't find it on 3Ware's site. On Sun, 28 Aug 2005 at 9:20am, Bryan J. Smith wrote >

I've just noticed that 3Ware has a more current version of the firmware for the 9500S than I have on several machines. All of mine are running: 3w-9xxx: scsi0: Firmware FE9X 3.04.00.005, BIOS BE9X 3.04.00.002, Ports: 8. and the latest rev appears to be 3.08. I'm wondering if there is any compelling reason to upgrade or just let these sleeping dogs lie. :) Any sage (or other)

Dear list, I thought I'd just share my experiences with this 3Ware card, and see if anyone might have any suggestions. System: Supermicro H8DA8 with 2 x Opteron 250 2.4GHz and 4GB RAM installed. 9550SX-8LP hosting 4x Seagate ST3250820SV 250GB in a RAID 1 plus 2 hot spare config. The array is properly initialized, write cache is on, as is queueing (and supported by the drives). StoreSave

I seem to have managed to end up with a pool that is confused abut its children disks. The pool is faulted with corrupt metadata: pool: d state: FAULTED status: The pool metadata is corrupted and the pool cannot be opened. action: Destroy and re-create the pool from a backup source. see: http://illumos.org/msg/ZFS-8000-72 scan: none requested config: NAME STATE

Hi, I've got a new server with a 3ware 9550SXU with the Battery. I am using FreeBSD 7.0-Release (tried both 4BSD and ULE) using AMD64 and the 3ware performance for writes is just plain horrible. Something is obviously wrong but I'm not sure what. I've got a 4 disk RAID 10 array. According to 3dm2 the cache is on. I even tried setting The StorSave preference to

Hello I have at this time a w3are 7006-2 controller in my server Dual Xenon 2.8Ghz . But now i will change it to a 9500S-4LP SATA Raid Controller. I have seen in lsmod that the 7000 driver is loaded. scsi_mod 115112 3 [sg 3w-xxxx sd_mod] My question Is it possible to running this card with centos 3.3? I have seen this at 3ware http://www.3ware.com/KB/article.aspx?id=12706 But

Hello list, I see through the archives that some people here use 3ware RAID controllers with Centos. I have picked up two 9500S-4LP controllers for future servers. I was hoping that if some people could please share their 3ware monitoring scripts with the rest of the group. What I am really hoping to do is have some setup where a cron job runs scripts to test each of the drives connected to the

I am getting this error:- 3w-9xxx: scsi0: ERROR: (0x03:0x0104): SGL entry has illegal length:address=0x3744A000, length=0xFF, cmd=X. In dmesg it finds the controller OK:- 3ware 9000 Storage Controller device driver for Linux v2.26.02.001. ACPI: PCI interrupt 0000:01:06.0[A] -> GSI 11 (level, low) -> IRQ 11 scsi0 : 3ware 9000 Storage Controller 3w-9xxx: scsi0: Found a 3ware 9000 Storage

Hello, Does anyone have experience using a 3ware 9650SE series raid controller on CentOS 6.0? I am getting very sporadic throughput with moderately sized files (0.5-2GB) on ext3. I have tried most of the mount time tuning options: * noatime * trying different journal types * setting commit=120 - helped a little Even after these optimizations it doesn't seem like the raid array is working

Hi all, after an uprade to new kernel 2.4.21-15.0.4.EL on my server appears a lot of these messages: EXT3-fs error (device sd(8,17)): ext3_free_blocks: bit already cleared for block 19268224 EXT3-fs error (device sd(8,17)): ext3_free_blocks: bit already cleared for block 19268225 EXT3-fs error (device sd(8,17)): ext3_free_blocks: bit already cleared for block 19268226 I try to rebuild array but

I''ve been attempting to update my dom0 kernel by using the 2.6.27 git tree from the xenclient repo and also to 2.6.30 using opensuse patches rebased by Andrew Lyon. In both cases there''s a problem with the 3ware 3w_9xxx driver incorrectly detecting the LUNs on the device or some other issue, which ultimately prevents partition table detection. In my testing I applied the

Hi, I used xen-3.0.2-2 (2.6.16) before and the performance of my 3ware 9550SXU-4LP wasn''t too bad, but now with 3.0.3.0 (2.6.16.29) throughput decreased by about 10MB/sec in write performance. sync; ./bonnie++ -n 0 -r 512 -s 20480 -f -b -d /mnt/blabla -u someuser now (2.6.16.29): Version 1.03 ------Sequential Output------ --Sequential Input- --Random- -Per

I've got a Centos 4 box at work, where I noticed a pile of old kernels lying around and no longer needed. I did "rpm -qa | grep -y kernel > list" then edited the list to remove from it the newer kernels, then "yum remove `cat list`". Yum has come up with a list of 71 packages it wants to remove, even though there were only 33 kernel-related RPMs in the list. this

greetings, the subject says it all right? ;-> naw...... is the 3ware Escalade 9500S series mature enough yet for CentOS? - rh -- Robert Hanson Abba Communications http://www.abbacomm.net

I have not used RAID controller boards to date since I have relied on the built in RAID on the motherboards. Thanks to the informative message Byron, I realize the deficiencies of doing RAID 1 this way, especially now that the builtin is out of date with Kernel used by Centos. I have 4 ATA drives that were configured in two pairs. I assume that I need a 3Wave controller that has 4 ports

I'm running FreeBSD 7.1-PRERELEASE over Asus P5Q motherboard. Such board comes with an nic requiring age0 driver. When the nic is under load, such trasferring big amount of data over gigabit connection (let's say some gigabyte backups), the computer hangs, sometimes with panic, sometimes freezing. Before that i was using an Intel nic with em0 driver and 7.0-Stable#2.. and that

http://www.3ware.com/KB/article.aspx?id=11843 "These instructions are for RH Advanced Server Update 2 and ****any other Linux distribution that does not include the driver for the 3ware 9000 series controllers.**** " The knowledgebase article also includes the aforementioned perl script(dug a bit more and found it).

In regard of the e-mail sent on Jul/16/04 about the 3Ware 9500S. Has anyone experienced/solved this issue ?? I'm having a similar problem, I already have the system installed on a separate disk, now I want to make the filesystem on the RAID partition (using 3Ware 9500S-8). First I had the problem that the card will keep resetting after continous timeouts whenever I tried loading the

We have created a Centos 9500S Floppy Boot Disk for installing Centos on a 3ware 9500S series controller that will allow installing and booting directly from this controller. This boot disk supports only AMD XP, MP and Opterons in 32 bit mode Centos 3.4 for the up and smp versions. We can also do a x86_64 version if required. Any interest???? If so we will post it to our web site. Thanks

From a buddy of mine that has spent a little time with the new cards. This was in response to my email asking about his impressions of them: It just came out in mid-September. There are a couple reasons I'm not thrilled with it: 1) no 8-port multilane version (only 12) 2) the 8-port non-multilane version is a kludge, connector-wise (a row of 3 double-stacked connectors along the