similar to: Premium CABLE TV .......No Monthly Bills!

Just for grins, pull off the cover and look at the electrolytic capacitors on the motherboard. Look for ones with the tops pushed up instead of being flat. This can cause all sorts of odd behavior. Often the machine with a blown capacitor will continue to run till it is powered off. Mostly I see this on Dell machines but have seen it on other machines as well. They are pretty easy to

Hello I have played about with a TDM400 card and plugged in some standard analog phones. I am using the card in FXS mode - for analog extensions. I did notice that one of my phones did not ring and I wondered why. I later read in Paul Mahler's book VoIP Telephony with Asterisk that in his section on the TDM400 on page 127 he says "In the UK, you may need an adapter that provides a

Three months ago, I was experiencing all sorts of issues with my Asterisk box maintaining a connection to multiple trunks, etc. I also experienced various timing issues as well. In addition, Asterisk would sometimes take almost a minute to fully load and register its SIP and IAX trunks. Puzzled, I recompiled several times. No result. I checked my hardware. Didn't find anything. However, I did

Styma, Robert (Nokia - US) wrote: > > Just for grins, pull off the cover and look at the electrolytic capacitors > on the motherboard. > Look for ones with the tops pushed up instead of being flat. This can > cause all sorts of odd behavior. Often the machine with a blown capacitor > will continue to run till it is powered off. Mostly I see this on Dell > machines but

I have an MGE Ellipse Premium 1200 that I connected to my server using its USB cable. Nut seems to be working fine. I've done a power down test and it worked and came back up when the UPS had power again. I'm using the newhidups driver and the USB cable. The problem I'm having is that if I boot with the cable connected newhidups says it can't find the UPS. If I unplug and plug in

Yes the flash-backed RAID cards use a super-capacitor to backup the flash cache. You have a choice of flash module sizes to include on the card. The card supports RAID modes as well as JBOD. I do not know if Gluster can make use of battery-backed flash-based Cache when the disks are presented by the RAID card in JBOD. The Hardware vendor asked "Do you know if Gluster makes use of

Hi all, I cant ring my phone with fxstest, but all else works (playing tones, stats , regdump). My ring voltage is -53.7680 volts as reported by stats option to fxstest. However, I can ring my phone with Asterisk !!! With fxstest, I just hear a click if I am off hook, and ask it to ring my phone. I am in the UK, and have a ring capacitor installed to the fxs port. Even without that,

My OQO mod2s just arrived! All 4 of them; portable testbed here it comes!!! I hope.... The units weigh in at ~.75lbs, and measure aprox. 5 5/8 x 3 3/8 x 1 1/8" A little larger when you push up the 5" screen to reveal the keyboard. WiFi, Bluetooth, HDMI, and a single USB built in; an adapter for VGA and Ethernet. (WiMax extra, I think the touch screen is also optional and I did

> >>> where in the filesystem should I be looking for the NUT shutdown script please? >> >> It's the SHUTDOWNCMD in upsmon.conf Excellent. And in my case (default) it says SHUTDOWNCMD "/sbin/shutdown -h +0" I have tried that command and, as expected, it has shut down the pc. Then I have disconnected the power cord for one minute and plugged it back in,

Thanks, The 3 servers are new Lenovo units with redundant PS backed by two huge UPS units (on for each bank of power supplies). I think the chances of losing two nodes is incredibly slim, and in that case a Disaster Recovery from offsite backups would be reasonable. My requirements are about 2TB, highly available (so that I can reboot one of the 3 servers without taking down services). Beyond

Is there a cable length limit to use with a fxsmod (TDM400B) ? I noticed that if I use a very long cable 148 feet, I can hear some parasite : I hear the radio ! If I use a short cable, there is no problem... Thanks for help, St?phane HENRY

On Tue, 2017-10-31 at 17:37 -0500, Matthew Delfino via samba wrote: > > > > I’m having a similar problem. I just fixed a bad member of my samba > domain - an samba AD DC that wasn’t working. I demoted it, > uninstalled Samba and reinstalled, then rejoined the domain. > > Everything's replicating nicely. All my users can authenticate. But > my samba AD DCs are all

Howdy, I have at several times had issues with consumer grade PC hardware and ZFS not getting along. The problem is not the disks but the fact I dont have ECC and end to end checking on the datapath. What is happening is that random memory errors and bit flips are written out to disk and when read back again ZFS reports it as a checksum failure: pool: myth state: ONLINE status: One or more

Sunday I updated my kernel to 128.1.16 (I had to reboot so it was time to update). No problems with wireless in my home. Monday I started traveling to IEEE 802 plenary, and I have lost my wireless numerous times needing to reboot. The symptom is the radio light goes off. Back before the kernel update, this would happen sometimes at home while on battery, and I would just press the

our price US $ 269.90 save: $1529.10 Adobe Photoshop CS3 Extended download http://gogisoftd.com

Hi, I have used /etc/init.d/rclevel.d/S12ups script renaming it with S22ups and adding at the top: chown root:nobody /proc/bus/usb/002/002 chmod 660 /proc/bus/usb/002/002 It's a patch but works. Best regards. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.alioth.debian.org/pipermail/nut-upsuser/attachments/20060209/aa742904/unnamed.htm

An HTML attachment was scrubbed... URL: http://lists.linux-foundation.org/pipermail/virtualization/attachments/20070714/94b02cee/attachment-0001.htm -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/png Size: 18113 bytes Desc: not available Url :

An HTML attachment was scrubbed... URL: http://lists.linux-foundation.org/pipermail/virtualization/attachments/20070714/94b02cee/attachment-0001.htm -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/png Size: 18113 bytes Desc: not available Url :

My new MGE Ellipse Premium 1200 is now working fine. I've tested pulling the plug and the computer shuts down properly and comes back up when I replug. The only strange behaviour is that when I put the power back on the battery shows as being at 86%. If it was at 86% it should have lasted longer. Is there any calibration step I can do? The only commands the ups seems to support are: $ upscmd

Hi, here in Italy we have a special kind of phone services that are named "audiotel", those services are also known as "premium". Audiotel services are billed in a different way from normal phone calls and the revenue is shared between the answering company and the telco, they are used to give weather information, chat party lines and so on. Inbound lines are coming over