similar to: problem_connection_NUT_infosec

Hello, I am trying to make my UPS system working with NUT but with no success. I got "No supported UPS detected" message. I use the blazer_usb driver since it was proposed to me by the web site. My NUT version is : 2.7.1 (installed from standard RPM), release 2.41 The UPS identification: INFOSEC X4 RM PLUS linux-2qya:~ # /usr/lib/ups/driver/blazer_usb -a infosec Network UPS Tools -

Hi everybody, In a christmas sequel I've been offered one of the units mentioned above. I've tried to connect it to my Fedora 8 workstation but rapidly concluded it's not yet supported by NUT. So far, I've decompiled the Java classes of the manufacturer's application and noticed that it's most probably yet another kind of serial protocol through the USB. Since

Bonjour, Je souheterais utilis? la version qui permet le '-x generic',mais je ne sais pas ou la recuperer car ca devrait solutionner mon probleme (cf mail ci-dessous) DaneZ _____ From: DaneZ [mailto:david.guillotte@danez.no-ip.org] To: arnaud.quette@mgeups.com Sent: Sat, 08 Jul 2006 23:24:06 +0200 Subject: Fw: INFOSEC 500 XP en USB _____ Bonjour Arnaud, Je me

Hello i need your help regarding the following issue : i have a hero touch ups from infosec. it is connected via USB to a raspberry pi 3. i?ve configure ups.conf file as below [HERO] driver = blazer_usb vendorid = 0665 productid = 5161 either with port = auto or port = /dev/hidraw0 or port = /dev/ttySo the connection never works i get the

Hi, I'm using debian sarge on my server and connected a MGE-ups ellipse via the serial port. I searched the internet for the answer, but can't find it. My config files: <upsd.users> [admin] password = pwd allowfrom = 127.0.0.1/32 actions = set instcmds = all [upsmon] password = pwd allowfrom = 127.0.0.1/32 10.0.0.224/32 upsmon master [upsslave] password

Hallo group, I am running openSUSE 10.3 with nut-2.2.0-20 installed. I have configured it as mentioned in /usr/share/doc/packages/nut/README.SUSE. on starting nut using "rcupsd start" i get following: # Starting NUT UPS monitor done Broadcast Message from root at pane (somewhere) at 22:27 ... Communications with UPS myups at localhost

hi i bought a ultra ULT31502 ups someone seem able to run this ups with nut just see Dean thread on: http://www.tigerdirect.com/applications/searchtools/item-details.asp?EdpNo=770423&Tab=11&NoMapp=0 i use suse 10.1, i installed nut the ups is connected directely to my computer with an usb cable lsusb return Bus 001 Device 004: ID 0d9f:0001 Powercom Co., Ltd with lsmod, i can see

Here are the results from the output of upsc under different conditions from my Debian Test system with NUT 2.7.2 : Normal: ups.status: OL No wall power: ups.status: OB Runtime calibration (started from AP9630 web interface): ups.status: OB CAL So at this stage there is a difference! I then connected to my QNAP and set the UPS settings on the web interface to "Shutdown server if power

Hi all, I've just upgraded my debian box from etch to lenny, and am now having Nut problems. I have read through the UPGRADING text (which helped fixed my first ups driver related problem), but have now hit another problem, which seems quite common, but non of the responses I've found on Google apply, so I'm coming to you for help. On issuing a "/etc/init.d/nut start"

Hello all, I'm having problems with what I'm told should be a straightforward issue. The message in /var/log/daemon is: <quote> Feb 13 10:37:57 lupin upsmon[31324]: Master privileges unavailable on UPS [lupin1500AVR@localhost]

Hi Charles, I am done with few things: I made the cable - looks good, because I see some activities. I upgraded NUT to 2.7.3. but I have no success to start driver(this are the outputs) nut.cfg MODE = netserver ups.conf [infosec] driver = nutdrv_qx (or blazer_ser) port = /dev/ttyS1 desc = "XP Pro 2500 RM" output(nutdrv_qx cmd upsdrvctl -DDD start) Network UPS

Greetings! I have successfully installed and configured nut package. All i want now is to power off ups. If i run upsmon -c fsd as root - everything goes fine, system and ups gracefully shutting down. If i unplug power cable from an ups, then system is down, but ups still on load. Any help would be appreciated. Debian Lenny x86 ups.conf [ippon] driver = megatec port = /dev/ttyS0

hi, i've just set up two new computers each with a Powerware 3105 ups. they have identical nut configurations and identical upss which are both plugged in via usb but only one is being detected by nut. the other keeps saying: Broadcast Message from nut at server-1 (somewhere) at 14:52 ... UPS ups at localhost is unavailable i tried plugging the ups into several different usb

Hi, I was trying to hack the /etc/rc.d/init.d/halt script under RH 9.0 in a way to achieve a clean shutdown: - commanding the RAID arrays to readonly mode - turning off my hardware watchdog, ... etc. See details below. At the end of all this preparation, and very close to the last lines of the halt script, I would then issue: 1. /usr/bin/belkinunv -x wait /dev/ttyS0 2. (OR, with a smart ups:

those mails list are from last century but i give it a try ! created : https://github.com/networkupstools/nut/issues/563 Hello all, Trying to run an EATON 850pro via USB on a Debian Stretch Stable. I have letsencrypt certificate installed and working. When trying to manage the EATON device, i got: upsmon Can not initialize SSL context When 850pro is connected via USB, i can: lsusb Bus 009

Hello All, I'm trying to establish a MASTER SLAVE configuration of UPS using NUT Driver. I'm able to shutdown the master after UPS is on BATTERY ( POWER BLACKOUT) .However I'm trying to shutdown the other SLAVE MACHINES BEFORE MASTER. But at the remote side ( Slaves ) shutdown after UPS blackout does not happen. My configuration in Master are /usr/etc/upsd.users

Hi I have an Infosec Hero touch lcd 400 USB ups but it is not recognised by Nut. I tried to use Blazer_usb too. Could you help me please ? Thank you very much! Https://www.infosec-ups.com/fr/#/dfclassic/query=Touch%20400&query_name=match_and -------------- next part -------------- An HTML attachment was scrubbed... URL:

InfoSec World(tm) Conference and Expo 2006 April 3-5, 2006 Vendor Expo: April 3 & 4 Optional Workshops: April 1, 2, 5, 6, & 7 Disney's Coronado Springs Resort / Orlando, FL http://www.misti.com/InfoSecWorld SPECIAL OFFER! SECNAP Network Security Corp. and MIS Training Institute would like to offer you 10% OFF of the regular undiscounted conference fee of $1495 to attend

No progress has been made: cable is UPS - PC 6 - 3 7 - 5 9 - 2 for ./blazer_ser -DDDDD -a infosec 0.000000 send_to_all: SETINFO driver.parameter.port "/dev/ttyS1" 0.000323 debug level is '5' 0.103068 send_to_all: SETINFO device.type "ups" 0.103104 send_to_all: SETINFO driver.version "2.7.3" 0.103118 send_to_all: SETINFO

Ubuntu 8.04 Nut : Version: 2.2.1-2.1ubuntu7.2 Hello, I choose the megatec driver and I connect through a serial cable. I receive a "This UPS has an unsupported combination of battery voltage/number of batteries" message. I know this is not an error but I don't really what I have to do next. Here is the result of /lib/nut/megatec -a infosec -DDD debug level is '3'