similar to: T.38 Gateway

Hello list, We're currently facing some issues concerning T.38 gateway faxing. This is a device used almost exclusively for receiving faxes. Calls are incoming to asterisk on a SIP trunk (sangoma netborder) using G711A. Gateway mode is activated in the asterisk dialplan towards a Cisco SPA 112 running firmware 1.3.5. We are using asterisk 1.8.13.0 with the T.38 gateway patch applied (I know I

Hello, Trying to set up res_fax_spandsp. Based on https://wiki.asterisk.org/wiki/display/AST/T.38+Fax+Gateway I wrote this in my extensions.conf: exten => 306,1,NoOp(Fax transmission) same => n,Set(FAXOPT(gateway)=yes) same => n,Dial(DAHDI/3) ----->FXS port to fax machine same => n,Hangup() Call flow Im trying to pull out is as follows: Zoiper -->

I am testing out inbound faxing using res_fax and res_fax_spandsp.so My system answers the call but then sets there on the ReseiveFax line then comes back with an error that it exceeded the maximum retries. How would I go about debugging this? Below is my very simple dialplan code I am using, and the fax show version gives the following as well. FAX For Asterisk Components:

We are using res_fax_digium with a Sangoma PRI card on asterisk 1.8.13 The docs at http://docs.digium.com/FAX/fax_for_asterisk_admin_manual.pdf indicate v34 is supported, but when I enable it I get the message "res_fax_digium.c:1624 dgm_fax_new: V.34 not supported, will be ignored." Is v34 only supported with SpanDSP? Also, the res_fax.conf.sample does not indicate v34 as a valid

I am working on some fax tools for some of my users. I am reading the https://wiki.asterisk.org docs for faxing. Is see Application_SendFax and Application_SendeFax has one been discondinued? Any feed back on using the res_fax module would be apperciated. Any examples or other. Thanks Bryant -------------- next part -------------- An HTML attachment was scrubbed... URL:

Dear list, happy new year! I am still trying to make T.38 work. In the meantime, I have upgraded to Asterisk 13.1.0, and I am using the most recent PJSIP library (compiling that stuff myself). My local fax software is capable of T.38, as is my ITSP; Asterisk sits in the middle, of course. Asterisk is in the same private subnet as the local fax software and talks to the ITSP through a NAT'd

I am testing Fax for Asterisk. But, I meet a problem. I try to Send a Fax (.tiff) from the first asterisk (Asterisk1) to the second asterisk (Asterisk2). Asterisk1 initiates an INVITE with audio G.711. Asterisk2 accepts this INVITE. Immediately, Asterisk2 sends an re-INVITE with T.38 to Asterisk1. But, Asterisk1 responds with "488 not acceptable here". I double check t38pt_udptl = yes in

To provide a reliable fax solution for users connected to a Asterisk 1.6.2.6 server i have tested a few T.38 capable ATA's: - Patton M-ATA - Grandstream HandyTone 486 - Fritz!Box 7170 I have tried Asterisk 1.6.2.6 compiled with SpanDSP-0.0.6pre17 and also Asterisk 1.6.2.6 with Fax for Asterisk installed. These Asterisk servers are connected to a Cisco PGW 2200 + AS5400XM. Sending fax

Hello, We have been working with the ReceiveFax application for some weeks now in order to receive faxes in T.38 and it works fairly well, but there are some faxes that for some reason we are not able to receive correctly. The asterisk version we are using is 1.6.0.6 with spandsp-0.0.5pre4 and the asterisk machine is behind a CISCO mediaGW to be able to communicate with the PSTN. The SIP call

Hi, On Thu, Jan 1, 2015 at 7:09 PM, Recursive <lists at binarus.de> wrote: > 1) Did anybody test T.38 with SPANDSP? If yes, which version of SPANDSP did you use? Mine is 0.0.6 PRE 20. Should I try to upgrade to PRE 21? Or to one of the snapshots? I remember that I was having issues with an older libspandsp library. I simply upgraded to the latest available version which made the issue

Hello users, Recently i have installed the free version of FaxForAsterisk and trying to work with it by sending a fax on T38. My version information is as follows i)Asterisk 1.6.0.20 ii)res_fax-1.6.0.14_1.1.6-x86_32 iii)res_fax_digium-1.6.0.14_1.1.6-i686_32 sip.conf [general] t38pt_udptl=yes extensions.conf [default] exten => _XXXXXXXXXX,1,NoOp(Fax Incoming Call) exten =>

Greetings- Working with the T.38 gateway functionality that is sparsely documented [1] , I'm attempting to get the following functional: Asterisk calling system -> Asterisk system in T.38 Gateway Mode (box in question) -> SIP Provider The problem is: -The provider is not initiating a reinvite to T.38, even though it is 100% supported -Asterisk is not detecting the CNG tones from

This message is pointed directly to Steve Underwood. I tought it would not be nice to directly email him with a question that interests a good part of the Asterisk community, so here it is. :) Steve, remember a few days ago when we discussed about issues on Asterisk 1.6.1.13 and T.38 fax reception? Well I opened an issue on Mantis (https://issues.asterisk.org/view.php?id=16756) and turns out it

Hello, I have a question regarding incoming fax to local file (on the Asterisk server). While the fax is received properly (I have the tiff file generated as expected) I get the warning 'FAX CNG detected but no fax extension' on the consol. If the fax is received ok then what 'fax extension' does it expect and what should I do there? My Setup: Sender -> Public PSTN ->

Hello List, I have been trying to setup T38 gatewaying with the following setup SIP ->Asterisk -> DAHDI TE410P with Libss7 -> TELCO I'm using asterisk Asterisk 1.8.3.2 and DAHDI Version: SVN-trunk-r9697M Echo Canceller: HWEC I'm aware there's no support for T38 gateway but I have been trying to get the patches https://issues.asterisk.org/view.php?id=13405 to work. It seems

Hi, I have asterisk 1.6.2.6 on a Debian Lenny system. When I try to send a fax in T.38 mode I receive this error ERROR[15035]: res_fax.c:795 set_fax_t38_caps: channel 'SIP/eutelia-sirio-out-00000000' is in an unsupported T.38 negotiation state, cannot continue. In my sip.config general section I have added this lines t38pt_udptl=yes t38pt_rtp=no t38pt_tcp=no If I comment this lines,

Hi, I tried to compile asterisk-1.8.0-beta4 but after ./configure && make I've got following error: [CC] res_fax.c -> res_fax.o [LD] res_fax.o -> res_fax.so [CC] res_fax_spandsp.c -> res_fax_spandsp.o res_fax_spandsp.c:117: error: field ?fax_state? has incomplete type res_fax_spandsp.c:118: error: field ?t38_state? has incomplete type res_fax_spandsp.c: In function

Hi All, I seem to have stumbled on a bit of a problem. When trying to send a fax with Fax For Asterisk on 1.6.2.x (have tried 1.6.2.5, 1.6.2.7 and the current svn version, with FFA 1.2 I get a core dump each time. Here is an extract form the console: [May 12 22:47:09] DEBUG[22584]: app_queue.c:1084 handle_statechange: Device 'SIP/vltb-sbc01' changed to state '1' (Not in use)

Hello, I have asterisk 1.6.2.9-2 I tried to install fax utility as it is shown on pdf documents on asterisk site. I downloaded Opteron compiled res_fax and res_fax_digium files and copied to /usr/lib/asterisk/modules/ where default modules directory is. I created a free fax license and created license file on asterisk server too. WHen i run asterisk it crashed. I noticed that if res_fax.so

Hello using asterisk 1.8, compiled res_fax.so and res_fax_spandsp.so - both loaded successfuly in sip.conf set t38pt_udptl=yes but faxes still don't work even in passthru mode. if i do a 'sip show channel' on the channel via which i am sending fax it shows: T.38 support Yes however if i do sip show channel of my channel (from other server) it shows T.38 support