similar to: usbhid-ups not finding CyberPower PP1100 on Fedora 16

I just got a Cyberpower SOHO Value 1200 ELCD UPS and even with nut 2.7.2, it appears to report battery voltage too low due to the battery scaling function (In drivers/cps-hid.c). Even though the ups has usb id: 0764:0501, UPS.PowerSummary.Voltage reports 26.6 for the 24V batteries so when the 0.667 battery scale is applied that goes down to 17.7V. upsc output: battery.charge: 100

Hi all, I've bought UPS FSP EP 850 because I have similar UPS, FSP EP 1000. It is working on my other server with with Fedora 14, kernel 2.6.35.14-106.fc14.x86_64 and installed nut-2.6.2-1. My new UPS is detected by kernel (see below lsusb output) and is partially detected by blazer_usb driver also. But it doesn't communicate with driver (see below blazer_usb output). I run all

Begin forwarded message: > From: James Erickson <jimerickso at gmail.com> > Date: August 10, 2009 2:50:52 PM EDT > To: Charles Lepple <clepple at gmail.com> > Subject: Re: [Nut-upsuser] CyberPower OR2200 > > On Sun, Aug 09, 2009 at 06:38:32PM -0400, Charles Lepple wrote: >> >>> From: James Erickson >>> Date: August 9, 2009 6:17:51 PM EDT

Hello list, ? ?Cannot make Evolution 850 to be recognized, maybe the problem is "Warning: incomplete endpoint descriptor" in lsusb? Details are as follows. NUT installed by download of debian package. Any ideas/suggestions are highly welcome, thanks in advance! --ValenteM = ? ?= ? ? = ? ? = Ubuntu server 12.04.1 LTS (GNU/Linux 3.2.0-35-generic x86_64) sudo dpkg -i

Hello, I've had this same model CyberPower connected to a linux server and a freebsd server. [root at sensor003 menon]# lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 004: ID 0764:0501 Cyber Power System, Inc. CP1500 AVR UPS Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus

Hi all, I?ve a UPS Liebert GXT3 500-3000VA with USB port. I?ve install NUT version 2.2.2 from repository packages for Debian Lenny. Linux kernel 2.6.26 I?ve try to use usbhid-ups driver in ups.conf [liebert] driver=usbhid-ups port=/dev/usb/hiddev0 Debian get the usb: # lsusb -v Bus 001 Device 002: ID 10af:0008 Liebert Corp. PowerSure Interactive UPS Device Descriptor: bLength

Hi Rok, I retired from working on NUT a few months ago, so I don't have the most up-to-date info. But the guys on the nut-upsdev mailing list (cc'd above) are very helpful. Both of your devices (or nearly identical ones) have been seen on the mailing lists before. The Sweex was first mentioned in a message by Eli Wapniarski on 14 Jun 2006 on nut-upsuser, and was most recently discussed

Hi all, just landed here so apologize. I've googled a lot but I can't find a way to get my UPS working with NUT. here my ( relevant ) details: lsusb ... ... Bus 001 Device 027: ID 0001:0000 Fry's Electronics ... ... lsusb -v -d 0001:0000 Bus 001 Device 027: ID 0001:0000 Fry's Electronics Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB

Hello, I am trying to get a "no-brand" (LMS DATA, model no LMSP1200RI) UPS to work with NUT. I now realise I should have checked compatibility with NUT before purchase. My other UPS (APC) works perfectly..... Anyway, I have spent a good day trying to get this thing working. #lsusb Bus 001 Device 003: ID 0001:0000 Fry's ElectronicsDevice Descriptor: bLength 18

I was able to make NUT and my Powercom SPIDER UPS (USB port) work under the Raspberry Pi Desktop (Debian). Everything works in VMware Workstation 15 Player. But my Raspberry Pi 3b + (with raspbian) doesn’t work with the same UPS, and with same NUT configuration. Raspberry sees the UPS, but the driver does not cling. Here is the response of Raspberry 3b + to some commands. pi at raspberrypi:~

Apologies for the long post. I'm trying to include what I hope are the relevant bits (output of lsusb -v and usbhid-ups) Long term goal: I've got a DIY UPS that I would like to get working with my QNAP NAS (which uses Linux and NUT underneath the hood) Immediate short-term problem: I can't get past running usbhid-ups on Ubuntu 23.10 with an Arduino Leonardo. I have an Arduino Micro

Hello all: I have a Yukai PowerMust 1000 USB and it used to work on another computer using megatec_usb driver. Now, I have it in a new computer, but the driver does not detect it. It is there: # lsusb|grep Cypress Bus 006 Device 007: ID 0665:5161 Cypress Semiconductor USB to Serial Permissions are OK: # ls -l /dev/bus/usb/006/007 crw-rw-r-- 1 root nut 189, 646 ago 8 01:51

At one time I had my Back-UPS ES-750 working with nut and the usbhid-ups driver. Not sure what has changed, but I can't get the driver to load now. It exits with this error: Network UPS Tools - UPS driver controller 2.2.2 Network UPS Tools: 0.29 USB communication driver - core 0.33 (2.2.2) No matching HID UPS found Driver failed to start (exit status=1) lsusb -v gives me: Bus 003 Device

Hello I have a remote Dell R310 to which I connected via USB a new UPS, model Eaton 5E1500I USB. Assuming I interpreted correctly the docs, it should normally work using the usbhid-ups driver. However, no matter what I tried, I get an error which you can also is included in the below paste: #usbhid-ups -DDDD -u root -x explore -x vendorid="0463" -a eaton Network UPS Tools

On Nov 10, 2017, at 5:31 PM, Christoph Lampl <chris at weeone.de> wrote: > > Dear Charles, > > thanks for your quick answer and your information! I didn't know there is a difference in the PR-series between old and new. So thanks for this valuable information! Just a lucky guess :-) We tend not to know about changes like this until someone reports an issue. > >

Can someone give me a push in the right direction with this? I'm trying to get an upsonic IRT1000 to work on ubuntu 14.04lts using the usb connection. The most likely drivers (blazer_usb and usbhid-ups) don't seem to recognize it or I've got the configuration parameters wrong. I've got no idea what driver it actually wants though there's an old thread that seems to have got

Hi All, I bought a USB Bluetooth dongle. However, it's not working for me. Please help, how to debug and get more information as I can not see any error or warning message from system log message. I checked http://thread.gmane.org/gmane.linux.bluez.kernel/22183/focus=22211, however, also find another page

Hi, just try the Unitek Self Protek Mistral 1000ipF with nut and I doesn't work. How can I correctly configure it (if the driver support it). Best regards, In my dmesg: [42953293.620000] usb 1-2: new low speed USB device using uhci_hcd and address 7 [42953293.760000] usb 1-2: no configurations [42953293.760000] usb 1-2: can't read configurations, error -22 [42953293.880000] usb 1-2: new

I was able to make NUT and my Powercom SPIDER UPS (USB port) work under the Raspberry Pi Desktop (Debian). Everything works in VMware Workstation 15 Player. But my Raspberry Pi 3b + (with raspbian last version) doesn’t work with the same UPS, and with same NUT configuration. Raspberry sees the UPS, but the driver does not cling. Here is the response of Raspberry 3b + to some commands. pi at

On Jan 21, 2020, at 7:50 AM, Gene Heskett <gheskett at shentel.net> wrote: > > Now I've got another of those WTF questions. This ups doesn't ID itself > the same to an lsusb as it does to upsc. > From an lsusb: > Bus 001 Device 004: ID 0764:0501 Cyber Power System, Inc. CP1500 AVR UPS The two IDs are vendor (VID) and product (PID). lsusb looks them up in a text