similar to: redirect-gateway and p2p-Traffic

Hi, I have made this script, that I use for controlling the bandwidth on a gateway for about 100 computers. It is working quite effectively to limit the use of p2p programs (and other programs), so that you can surf undisturbed. Also, it improves internet access in general, so that one large download doesn''t take up all your bandwidth. I was wondering if someone would like to test it,

Hi, Guus I did some test regarding the points you mentioned below, and yes, you’re right, but some of points may need further adjusted: 1. The destination of IPv4 wouldn’t be changed, Yes I agree, that’s the goal and final destination for the communication. But during the path, it may be encapsulated into another packet(tunnel mode), where the outside IP header is the physical address, but the

I have been delighted by tinc. Building a mesh like I need would have been horrible in OpenVPN. tinc makes it easy. I decided to share a workaround for a problem that's been vexing me. Either I'm being dumb (and can do this better with a hint) or this is something others might need. I've been moving a bunch of services from our university to Amazon (EC2). To do this, I bring

Trying to understand "redirect-gateway" option Is this url info correct for the current Tinc 1.0.35 version? .../tinc-vpn.org/examples/redirect-gateway What is the script? /etc/tinc/myvpn/hosts/server-up Is it really a extra bit to be added to,/etc/tinc/myvpn/tinc-up If I read and apply the instructions to my routed setup, then all I need to add isip route add 0.0.0.0/1 dev $INTERFACE

Greetings, I''ve searched, found ftwall, and some other commercial solutions, but am wondering if anyone on this list has any solutions using a linux firewall to block p2p traffic, more specifically Kazaa. Walter Wickersham _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hi all, I have just upgraded to a new satellite internet provider. I have two network cards - one with a public IP connected to my satellite router, and the second network card with private IP into my switch for the LAN. Shorewall firewall My old satellite system is not being used. Would it be possible/feasable to install a third network card into my Fedora Core 2 server, and then direct all

I do not how to use match string to deny kazaa traffic, if I put the word kazaa only http content is deny but the kazaa aplication is running, are there special commands to match string? thanks _________________________________________________________________ Charla con tus amigos en línea mediante MSN Messenger: http://messenger.microsoft.com/es

Hello I''ve setuped a bridge with l7-filter and ipp2p. We have every day + or - between 10Mbits and 30 Mbits P2P traffic from + or - 450 customers. When traffic increase. I''ve got this kind of error message : Feb 23 14:26:19 gestor1 kernel: printk: 38 messages suppressed. Feb 23 14:26:19 gestor1 kernel: ip_conntrack: table full, dropping packet. The server is celeron

After varying degrees of success with p2p detection modules, I would like to write the following rules using iptables to reliably identify p2p traffic: 1. If a host on the network has 5 or more simutaneous tcp connections to ports above 1024, mark all connections to ports 1024 and above as 60. 2. If a host has received (or sent) UDP packets from 5 different hosts'' ports above 1024 in a

Hello folks, for monitoring purposes I need to query the network status in order to get all a list of all "online" nodes (that are connected to the network right now). How can I do so? Thanks in advance, Keep smiling yanosz

Hello, I'm looking forward for release 1.1 esp. tincctl. Are there any release plans yet? Thanks, Keep smiling yanosz

Hi I have to manage a network with approx. 200 users, a 256kbit/s unmanaged Internet connection and a 3Mbit/s unreliable managed Internet connection (only http/ftp-proxy and ssh available). All users are in one Class C Subnet with 512 IP-Addresses. 60% of the machines are Windows. The rest are SUN and Linux. At the moment Windows viruses and p2p-traffic eats most of our bandwidth. My Aims are:

Hello folks, we're planning an IPv6-Deployment using tinc. A routed tinc-network should connect a couple of wireless access points. In order to avoiding scaling issues, the network should not be run in switched mode. Our site uses 2001:470:780f::/56 - Each ap gets a single /64 network, to be distributed to its wireless clients. Example: ap 1: 2001:470:780f:1::/64 ap 2:

Sure, let me reply all here for my finding. @Lars @Guus A’s tinc.conf: Name = bright AddressFamily = ipv4 ConnectTo = aly_hk A’s tinc-up: #!/bin/sh ifconfig $INTERFACE 10.0.0.110 netmask 255.255.255.0 A’s host config: Subnet = 10.0.0.110/32 (VPN address) Subnet = 192.168.31.0/24 (LAN address) IndirectData = yes (enabled for every tinc nodes) The node aly_hk (vpn address 10.0.0.3) connects with

Hi Guus, Am Freitag, den 25.09.2015, 17:04 +0200 schrieb Guus Sliepen: > Ok, that means by default the UDP NAT timeout on the Cisco is extremely > short. > > > I check the manual of the the Cisco NAT for any TCP/UDP > > timeout settings, but there is no way to modify anything like "keeps > > TCP/UDP connections alive". > > It wouldn't be called

Hi all, I''m tring to isolate P2P traffic, specifically BitTorrent, for my QoS scripts. I can''t seem to completely isolate ALL BitTorrent traffic. I identify & mark packets and then use tc filters to put them into appropriate classes. My firewall rules (below) do the markings. My VoIP boxes'' and ICMP traffic get highest priority (mark 1). Then comes DNS, SSH,

Hi, I have a linux fileserver on my local network which (besides other things) serves as p2p machine. The network is connected to the internet through a hardware ADSL (512/256) router. What happens now is that my SSH and webtraffic (from other machines) becomes bogged down when loads of up- and downloads happen at the fileserver. As the fileserver does not do NAT for me, I can''t use

Hello, I''m having trouble with transactions with rails 3.0.3 and mysql 5. I''d like to import data etl-batch-style: class Job < ActiveRecord::Base # ... def perform_etl connection.transaction do extract # some connection.execute / job.update_attribute stuff transform # some connection.execute / job.update_attribute stuff end end #... end

https://bugzilla.samba.org/show_bug.cgi?id=9624 Summary: rsync p2p extensions Product: rsync Version: 3.1.0 Platform: All OS/Version: All Status: NEW Severity: enhancement Priority: P5 Component: core AssignedTo: wayned at samba.org ReportedBy: mark at ibiblio.org QAContact:

Hello, some days ago, I was asking for help here about not able to do anything when I had bittorrent running, I will post the problem here: I''m using ipp2p to mark p2p packets, and then send them with -j CLASSIFY to the correct HTB class, I see traffic in the class when I start azurerus, and traffic does get shaped, but then I''m still not able to surf the web nor chat nor