similar to: tinc problem with windows

ofcourse there is no freepbx, and there is no difference between the version of asterisk , ATM we are using asterisk 1.6.2.19 , i've also tried it on asterisk 1.10 , which resulted in the same way , does anyone have any ideas , why is it happening like this . thank you. On 9 January 2012 14:30, <tinc-request at tinc-vpn.org> wrote: > Send tinc mailing list submissions to >

actually at the moment the setup is like this , it has the same ip address , both lan and tinc , but iax doesn't work at all , moreover , i want to be able to make an IAX trunk to the rest of the machines from different networks together . what happens is that , asterisk says that the request is sent , but nothing will be received . if you want i can try to make a tcpdump tomorrow , and send

Hey everyone , I'm using tinc from iran , and i've been using tinc with tcponly for a few years now , to bypass the filtering , and have access to the free internet , but recently , our government started to apply some sort of exotic filtering scheme , they've completely blocked outgoing and incoming ssh requests , and ssl encrypted packets , and the only thing allowed is https !! ,

Hi everyone , i have a large network , connected together by tinc , and the whole network is connected so that i can access all the devices through out the networks simply and easily , but when i try to interconnect my asterisk servers usin iax , it doesn't work , if i try to register to my server using the tinc's interface it's ok, the registry is done ok , and the connection works

i need forwarding off , cause i need a central node , which is connected directly to all the network , directly , so it can usually upload content directly , without slowing down other nodes in the network , i also don't want it to act as a forwarder , since ,it only has 2mbps of bandwidth , and i don't want it for that purpose , is there any other way to fix this problem ? On 16 March

Hi everyone , i have a few questions/problems with tinc , which i need to address ASAP , so i'll make it brief . i have 33 sites , connected with each other using wan , in each site , there are two linux firewalls + 3-4 more servers , i preferred to have a full mesh within my network , but unfortunately it was not possible , when i wanted every site to be connected to every other , as the

Hello everyone, I'm actually using tinc mostly to route all my traffic to another server , and my internet provider does all sorts of shaping and packet inspection to the outgoing packets, including but not limited to shaping encrypted TCP sessions , and re-routing UDP connections every few minutes and even blocking IP addresses in case too many users are connected with a traffic other than

Hi , at the moment i'm managing a distributed network country wide , which i want to use tinc on all the machines so we can have direct access to all the servers (including those behind firewall) . the problem arises with the fact that , my firewalls are connect to two separate networks , one is actually a country wide network , and the other is internet access , is there a way , that tinc

Hi , I've added one node to my tinc mesh , with forwarding off , and the network got splitted into several pieces !!, the thing is that , the node with forwarding off is connected to all hosts , directly with connect to , and seems like that for some nodes the shortest path , that the tinc network can find is through the node with forwarding off , here are the results of my first ping to all

Beste tinc-developer, Ik moet van mijn baas een aantal VPN's aanleggen en ben nu thuis bezig om te testen. Ik heb 2 computers in een thuisnetwerkje (totaal 6 computers) geinstalleerd met SuSe 7.3, daar de klanten dit ook hebben. De computers zijn verbonden met een switch. Dit is de inhoud van mijn bestanden: Op computer 1 genaamd suse met ip 192.168.0.99 netmask 255.255.255.0

Hi! Me and two friends are trying to get a VPN working, but we cant get routing between two tunnels. This is how it looks, all servers (192.168.*.1) are running IP Masquerade to enable the other computers behind them to access the internet. Both elayne and glenn are connecting to melc, and the tunnel between melc and glenn are running TCPOnly because that glenn doesnt have a public IP (it's

"PrivateKeyFile" as this is default, otherwise configuration is quite minimal. ======= Configuration ========= Server Side =========== # cat tinc.conf Name = fsvpns3f30 Mode = switch Device = /dev/net/tun AddressFamily = ipv4 PingInterval = 30 PrivateKeyFile = /etc/tinc/fsvpn/rsa_key.priv # cat tinc-up #!/bin/sh ifconfig $INTERFACE 10.10.100.30 netmask 255.255.0.0 # cat

Using tinc1.0pre5 Three machines A, B, and C tinc.conf on A: ----------------- Name = A PrivateKeyFile = /usr/local/etc/tinc/vpn/rsa_key.priv Device = /dev/tun ConnectTo = B tinc.conf on B: ----------------- Name = B PrivateKeyFile = /usr/local/etc/tinc/vpn/rsa_key.priv Device = /dev/tun ConnectTo = C A is up and connected to B which is up. Machine C is down. The log on B shows it

Hi folks. At the moment I'm using tinc to connect to linux boxes, both of which are behind NAT. This works just fine. I'd now like to connect some roaming windows users to the network so they can browse a samba share like I can already do with linux. These folk will likely have dynamic IP addresses. The server has an IP of 10.0.0.2 My client has an IP of 192.168.1.100 Here's what

Dear Tinc developer, I have some problems connecting to the other site of the VPN Here are my configuration files on pc1 Configuration files on pc2 /usr/local/etc/tinc/tinc.conf /usr/local/etc/tinc/tinc.conf Name = pc1 Name = pc2 TapDevice = /dev/tap0 TapDevice = /dev/tap0 PrivateKeyFile =

I'm really trying to do a client to server connection more than an ethernet bridge, but I couldn't figure out from the docs where that comes in. Client is Kubuntu Breezy, and server is Debian Sarge. Tinc was installed with apt-get on both systems. Version on server is 1.0.3, on client is 1.0.4. I've spent the entire day toiling over getting this set up. I had ipchains rules, etc,

El 12 de febrero de 2016 16:51:59 CET, Eric Yau <ericyaukhy at hotmail.com> escribi?: >Hi All, > > > >I am trying to setup the site-to-site VPN with TINC for connect my home >network to company network. Here is the IP allocation and configuration >for >your reference. > > > >Home PC (192.168.1.2) ?-----? Home (OPENWRT Router, 192.168.1.1, >10.0.0.1)

Hello, I've been trying to get bridging working on os x for about a week and haven't been able to do it. I've exhausted the examples and google and just can't get it to work. Any help would be appreciated, as I'm about to give up :( The goal is to join our two 192.168.1.x networks and share a large 192.168.1.x network between the two of us. Our setup is as follows:

Hi I've compiled Tinc 1.0.2 from source but I'm having trouble. Not only am I having disconnections all the time (could be a network issue however) but even worse, Tinc is ignoring my MaxTimeout = 60 and is waiting longer and longer and longer (logfile shows it at 120 seconds). Is this a bug or have i misconfigured anything? best regards Marco Amrein Dec 5 11:25:12 frank

Hi folks, Sorry to trouble you all - I'm having some trouble getting tincd up and running - I suspect I'm having problems with subnets. Any help would relaly be appreciated! At the moment I'm trying to get two linux boxes, both of which are running as NAT routers for their respective networks to talk. My goal is to allow staff to connect to the corporate network from their laptops