similar to: Tinc connects but no bridge

Hi all, There's long time I'm having problems with a vpn... I'd be glad if somebody could check my current setup. Our problem is we're having tinc-vpn shortcuts while we have no bandwidth problem nither 'ssh' trouble. I attached some log lines from both the "server" and the "client". Some ASCII art... ___ ___ ___

Hello! I'm trying to make a wireless mesh network with b.a.t.m.a.n. protocol, and I would like to secure the wireless links with tinc. My test network is 2 wireless routers with OpenWRT Kamikaze firmware, and the network topology is the following: |CLIENT|eth0: 192.168.180| <--> |eth0: 192.168.1.1|MESH-NODE|ath0: 192.168.5.54| <~~> |ath0: 192.168.5.51|GW|eth1: 192.168.1.51|

Hi! Me and two friends are trying to get a VPN working, but we cant get routing between two tunnels. This is how it looks, all servers (192.168.*.1) are running IP Masquerade to enable the other computers behind them to access the internet. Both elayne and glenn are connecting to melc, and the tunnel between melc and glenn are running TCPOnly because that glenn doesnt have a public IP (it's

"PrivateKeyFile" as this is default, otherwise configuration is quite minimal. ======= Configuration ========= Server Side =========== # cat tinc.conf Name = fsvpns3f30 Mode = switch Device = /dev/net/tun AddressFamily = ipv4 PingInterval = 30 PrivateKeyFile = /etc/tinc/fsvpn/rsa_key.priv # cat tinc-up #!/bin/sh ifconfig $INTERFACE 10.10.100.30 netmask 255.255.0.0 # cat

Hi folks. At the moment I'm using tinc to connect to linux boxes, both of which are behind NAT. This works just fine. I'd now like to connect some roaming windows users to the network so they can browse a samba share like I can already do with linux. These folk will likely have dynamic IP addresses. The server has an IP of 10.0.0.2 My client has an IP of 192.168.1.100 Here's what

Hi all, I have been using tinc successfully for a while now. However, I need to do something different from my normal setup, and i am getting the feeling I am doing something obvious wrong. What I want to do is hookup 5 distant linux routers into one bigger network, Since I need to transmit both unicast and multicast traffic, the VPN network has to be in "Mode = switch" [Assumption

Hello, I am experiencing some weird problems in a setup with tinc where communication between the 'server' and the 'clients' occur over 3g connections. Let me describe briefly the setup: - The server, on a public IP, runs tinc 1.0.8, in router mode, and the whole setup uses one VPN network. All client's VPN addresses are on the same subnet, and each client has a seperate

I apologize for the TLDR-style email, but I wanted to demonstrate that I have done a lot of work (11 hours and at least 8 tutorials including the tinc docs) before asking for help. My basic problem is this: tinc appears to properly connect and authenticate the client to the server, but I cannot ping or access resources. (yes. I know there is no 'server' in tinc, but 'server'

Hi , today i was trying to connect my windows 7 client to my tinc server and i ran into a strange problem :) my tinc server is running tinc 1.0.11 on ubuntu 10.04 in switch mode , and the windows client is running tinc 1.0.13, there is a very strange problem , i tried to connect the windows system , i configured it , and it didn't work , so i ran it in debug mode -D -d5 , and it told me: Got

Guus, or anyone that will help ... Okay.. I've been running tinc for a few months now, and Its been working pretty well with my machine. Attempts to install it on others WinXP Pro, WinXP Home, and WinNT boxes have been spotty at best, with some installations working perfectly, and some not working at all. My latest issue is this. My windows 2000 machine can connect perfectly to our external

Hello again :) Thank you all for your reply's. Below are the config files of the 3 hosts. I use  tinc in router mode. I do not have a kernel mode config lines anywhere so tinc must be using the default settings here. I added the ipaddressx to subnets on hostc and this works. Traffic to that ip is now routed via hostc. But since this ipaddressx address changes often I need to resolve it

Hi I've compiled Tinc 1.0.2 from source but I'm having trouble. Not only am I having disconnections all the time (could be a network issue however) but even worse, Tinc is ignoring my MaxTimeout = 60 and is waiting longer and longer and longer (logfile shows it at 120 seconds). Is this a bug or have i misconfigured anything? best regards Marco Amrein Dec 5 11:25:12 frank

Hello, response time: how is it possible to increase the response time on Tinc VPNs. When I use tinc over a fast or giga-bit network connection the ping-response time is normally about 1800 to 2000 ms. Sometimes I get ping response times at about 2.500 to 3.000 ms over a normal Ethernet Connection or a television-cable connection within the same providers-network in the same city. The ping-time

Beste tinc-developer, Ik moet van mijn baas een aantal VPN's aanleggen en ben nu thuis bezig om te testen. Ik heb 2 computers in een thuisnetwerkje (totaal 6 computers) geinstalleerd met SuSe 7.3, daar de klanten dit ook hebben. De computers zijn verbonden met een switch. Dit is de inhoud van mijn bestanden: Op computer 1 genaamd suse met ip 192.168.0.99 netmask 255.255.255.0

On 11 April 2018 at 11:30, Hans de Groot <hansg at dandy.nl> wrote: > Hello again :) > > Thank you all for your reply's. Below are the config files of the 3 hosts. > I use tinc in router mode. I do not have a kernel mode config lines > anywhere so tinc must be using the default settings here. > > I added the ipaddressx to subnets on hostc and this works. Traffic

Hi, I'm having some trouble trying to run tinc over GNU httptunnel. On server A I have: /etc/tinc/netname/tinc-up: #!/bin/sh ifconfig $INTERFACE 10.3.0.1 netmask 255.255.0.0 /usr/bin/hts -F localhost:655 8888 /etc/tinc/netname/hosts/A: Address = foo.com Subnet = 10.3.0.0/24 TCPonly = yes /etc/tinc/netname/hosts/B: ConnectTo = A Subnet = 10.4.0.0/24 TCPonly = yes

Using tinc1.0pre5 Three machines A, B, and C tinc.conf on A: ----------------- Name = A PrivateKeyFile = /usr/local/etc/tinc/vpn/rsa_key.priv Device = /dev/tun ConnectTo = B tinc.conf on B: ----------------- Name = B PrivateKeyFile = /usr/local/etc/tinc/vpn/rsa_key.priv Device = /dev/tun ConnectTo = C A is up and connected to B which is up. Machine C is down. The log on B shows it

Dear Tinc developer, I have some problems connecting to the other site of the VPN Here are my configuration files on pc1 Configuration files on pc2 /usr/local/etc/tinc/tinc.conf /usr/local/etc/tinc/tinc.conf Name = pc1 Name = pc2 TapDevice = /dev/tap0 TapDevice = /dev/tap0 PrivateKeyFile =

El 12 de febrero de 2016 16:51:59 CET, Eric Yau <ericyaukhy at hotmail.com> escribi?: >Hi All, > > > >I am trying to setup the site-to-site VPN with TINC for connect my home >network to company network. Here is the IP allocation and configuration >for >your reference. > > > >Home PC (192.168.1.2) ?-----? Home (OPENWRT Router, 192.168.1.1, >10.0.0.1)

Hello, I've been trying to get bridging working on os x for about a week and haven't been able to do it. I've exhausted the examples and google and just can't get it to work. Any help would be appreciated, as I'm about to give up :( The goal is to join our two 192.168.1.x networks and share a large 192.168.1.x network between the two of us. Our setup is as follows: