similar to: Tinc on Windows

Hi! Me and two friends are trying to get a VPN working, but we cant get routing between two tunnels. This is how it looks, all servers (192.168.*.1) are running IP Masquerade to enable the other computers behind them to access the internet. Both elayne and glenn are connecting to melc, and the tunnel between melc and glenn are running TCPOnly because that glenn doesnt have a public IP (it's

I'm really trying to do a client to server connection more than an ethernet bridge, but I couldn't figure out from the docs where that comes in. Client is Kubuntu Breezy, and server is Debian Sarge. Tinc was installed with apt-get on both systems. Version on server is 1.0.3, on client is 1.0.4. I've spent the entire day toiling over getting this set up. I had ipchains rules, etc,

Hello, response time: how is it possible to increase the response time on Tinc VPNs. When I use tinc over a fast or giga-bit network connection the ping-response time is normally about 1800 to 2000 ms. Sometimes I get ping response times at about 2.500 to 3.000 ms over a normal Ethernet Connection or a television-cable connection within the same providers-network in the same city. The ping-time

Hello, I am experiencing some weird problems in a setup with tinc where communication between the 'server' and the 'clients' occur over 3g connections. Let me describe briefly the setup: - The server, on a public IP, runs tinc 1.0.8, in router mode, and the whole setup uses one VPN network. All client's VPN addresses are on the same subnet, and each client has a seperate

Guus, or anyone that will help ... Okay.. I've been running tinc for a few months now, and Its been working pretty well with my machine. Attempts to install it on others WinXP Pro, WinXP Home, and WinNT boxes have been spotty at best, with some installations working perfectly, and some not working at all. My latest issue is this. My windows 2000 machine can connect perfectly to our external

"PrivateKeyFile" as this is default, otherwise configuration is quite minimal. ======= Configuration ========= Server Side =========== # cat tinc.conf Name = fsvpns3f30 Mode = switch Device = /dev/net/tun AddressFamily = ipv4 PingInterval = 30 PrivateKeyFile = /etc/tinc/fsvpn/rsa_key.priv # cat tinc-up #!/bin/sh ifconfig $INTERFACE 10.10.100.30 netmask 255.255.0.0 # cat

Hello again :) Thank you all for your reply's. Below are the config files of the 3 hosts. I use  tinc in router mode. I do not have a kernel mode config lines anywhere so tinc must be using the default settings here. I added the ipaddressx to subnets on hostc and this works. Traffic to that ip is now routed via hostc. But since this ipaddressx address changes often I need to resolve it

Hi , today i was trying to connect my windows 7 client to my tinc server and i ran into a strange problem :) my tinc server is running tinc 1.0.11 on ubuntu 10.04 in switch mode , and the windows client is running tinc 1.0.13, there is a very strange problem , i tried to connect the windows system , i configured it , and it didn't work , so i ran it in debug mode -D -d5 , and it told me: Got

Hi all, I have been using tinc successfully for a while now. However, I need to do something different from my normal setup, and i am getting the feeling I am doing something obvious wrong. What I want to do is hookup 5 distant linux routers into one bigger network, Since I need to transmit both unicast and multicast traffic, the VPN network has to be in "Mode = switch" [Assumption

Hey guys, Stumbled upon tinc a few days ago - looks great. I'm having trouble setting up a simple VPN between two machines that are unfirewalled, one is a physical machine and another is a local VM. I can connect to them via their existing LAN IPs and ping them without issue with < 1ms. 1) I have WinA (Windows host - existing LAN IP 192.168.137.1) and LinuxB (Linux host - existing LAN

Hi I've compiled Tinc 1.0.2 from source but I'm having trouble. Not only am I having disconnections all the time (could be a network issue however) but even worse, Tinc is ignoring my MaxTimeout = 60 and is waiting longer and longer and longer (logfile shows it at 120 seconds). Is this a bug or have i misconfigured anything? best regards Marco Amrein Dec 5 11:25:12 frank

On 11 April 2018 at 11:30, Hans de Groot <hansg at dandy.nl> wrote: > Hello again :) > > Thank you all for your reply's. Below are the config files of the 3 hosts. > I use tinc in router mode. I do not have a kernel mode config lines > anywhere so tinc must be using the default settings here. > > I added the ipaddressx to subnets on hostc and this works. Traffic

El 12 de febrero de 2016 16:51:59 CET, Eric Yau <ericyaukhy at hotmail.com> escribi?: >Hi All, > > > >I am trying to setup the site-to-site VPN with TINC for connect my home >network to company network. Here is the IP allocation and configuration >for >your reference. > > > >Home PC (192.168.1.2) ?-----? Home (OPENWRT Router, 192.168.1.1, >10.0.0.1)

Hi, I'm having some trouble trying to run tinc over GNU httptunnel. On server A I have: /etc/tinc/netname/tinc-up: #!/bin/sh ifconfig $INTERFACE 10.3.0.1 netmask 255.255.0.0 /usr/bin/hts -F localhost:655 8888 /etc/tinc/netname/hosts/A: Address = foo.com Subnet = 10.3.0.0/24 TCPonly = yes /etc/tinc/netname/hosts/B: ConnectTo = A Subnet = 10.4.0.0/24 TCPonly = yes

Beste tinc-developer, Ik moet van mijn baas een aantal VPN's aanleggen en ben nu thuis bezig om te testen. Ik heb 2 computers in een thuisnetwerkje (totaal 6 computers) geinstalleerd met SuSe 7.3, daar de klanten dit ook hebben. De computers zijn verbonden met een switch. Dit is de inhoud van mijn bestanden: Op computer 1 genaamd suse met ip 192.168.0.99 netmask 255.255.255.0

Hi All, I am trying to setup the site-to-site VPN with TINC for connect my home network to company network. Here is the IP allocation and configuration for your reference. Home PC (192.168.1.2) ?-----? Home (OPENWRT Router, 192.168.1.1, 10.0.0.1) ?----------------? INTERNET ?-------------? COMPANY (Windows 7 PC,192.168.2.1, 10.0.0.2) ?------------? COMPANY (SERVER ZONE) ?----? SERVER A

Hi folks, Sorry to trouble you all - I'm having some trouble getting tincd up and running - I suspect I'm having problems with subnets. Any help would relaly be appreciated! At the moment I'm trying to get two linux boxes, both of which are running as NAT routers for their respective networks to talk. My goal is to allow staff to connect to the corporate network from their laptops

Hi all, There's long time I'm having problems with a vpn... I'd be glad if somebody could check my current setup. Our problem is we're having tinc-vpn shortcuts while we have no bandwidth problem nither 'ssh' trouble. I attached some log lines from both the "server" and the "client". Some ASCII art... ___ ___ ___

Hello, I have 2 hosts HostA and HostB HostA - 10.38.9.2, kernel 2.4.16, tincd from Debian package HostB - 10.38.9.223, kernel 2.2.17-21mdk, tincd from tarball package. HostA: ------------------------------ /etc/tinc/test4/tinc.conf Name = HostA ConnectTo = HostB TapDevice = /dev/misc/net/tun PrivateKeyFile = /etc/tinc/test4/rsa_key.priv /etc/tinc/test4/hosts/HostA Subnet = 10.0.0.0/8 Port =

Hi guys!! I've followed the windows 2000/xp tutorial and not only, but it seems not to work! I've for sure committed some errors... PC (under NAT) files: tinc/vpn/tinc.conf tinc/vpn/rsa_key.priv tinc/vpn/hosts/elegos tinc/vpn/hosts/shadowkrad tinc.conf: Name = elegos ConnectTo = shadowkrad TCPOnly = yes Interface = VPN (TCPOnly as under a NAT) rsa_key.priv: -----BEGIN RSA PRIVATE