similar to: Address Variabme for Roadwarriors

Thanks for getting back to me so quickly on this. In thinking about the topology that I am trying to set up, I will probably only set up a "private" DNS on the VPN for the 10.x.x.x users. With this in mind, I have now come up with a new question relating to this. What I will like to do is to give all of the uses, including roadwarriors, a static IP address on the 10.x.x.x address

Hi again, which is the recommended procedure to get users (roadwarriors) with their windows laptops connected to the tinc daemon running on our firewall? What should we install on the laptop and how should we configure it? Thanks Andy Tinc: Discussion list about the tinc VPN daemon Archive: http://mail.nl.linux.org/lists/ Tinc site: http://tinc.nl.linux.org/

While I have concentrated on support for 2.6 native IPSEC in release 2.2.0, I am still of the opinion that unless you absolutely need IPSEC compatibility that OpenVPN is a much easier (and in the case of roadwarriors, a much better) solution. Having already generated all of the required X.509 certificates, it took me less than 1/2 hr to replace my IPSEC testbed with an OpenVPN one using the new

Thanks Guus for answering all of these many emails. I now had a question as to if it is possible for something like this. Suppose that you have a Tinc VPN network made up of 4 nodes (A, B, C, D) and you want to dynamically add new nodes (E, F). How can this be done without having to re-start all of the nodes A-D? Based upon what I can see, each node condifuration files need to be modified

Thanks Guus for answering all of these many emails. I now had a question as to if it is possible for something like this. Suppose that you have a Tinc VPN network made up of 4 nodes (A, B, C, D) and you want to dynamically add new nodes (E, F). How can this be done without having to re-start all of the nodes A-D? Based upon what I can see, each node condifuration files need to be modified

Hello, i have got a problem with the configuration of an roadwarrior ipsec VPN tunnel with shorewall 2.2.3. I read the Shorewall Kernel 2.6 IPSEC and folowed the instructions to that point where to modify the hosts with the folowing parameters: vpn eth0:0.0.0.0/0 ipsec But i have got an entry like net eth0:0.0.0.0/0 even in the same file: If i

Tom, After reading your latest postings, I am correct in understanding that, even with the netfilter-ipsec and policy patches in kernel 2.6, I still would not be able to connect more that one roadwarrior at a time? Mitch

Hi list! I'm sure the topic has been discussed but I could not find what I was looking for. What would be the best / easiest VPN software solution. I would like to install vpn software on the * server for roadwarriors to connect to with laptops running windows. Ideally the vpn solution will not require any additional software on the client side but will use IPSEC. (Ofcourse call quality

Dear tinc community, I am using tinc in switch mode. I have three nodes. Two nodes reside on routers, vpn-eth is bridged with internal lan, each router has several machines connected to it's internal lan. Third node is the roadwarrior - "endpoint" linux PC. When the roadwarrior is off - everything works perfectly, machines on both sides can communicate without a problem in any

Tuomo Soini wrote: > You don''t happen to read shorewall-devel mailinglist ? I read it -- I just didn''t know what to make of your post and it arrived while I was on vacation. What exactly are you trying to accomplish that Shorewall isn''t doing for you now? e.g. /etc/shorewall/zones rw Roadwarriors Road Warriors /etc/shorewall/interfraces rw ipsec+

Hi all, I''ve been using Shorewall 1.42 for a month on two firewalls at work and my own personal colocated server and love it. While pretty familiar with iptables, I don''t like dealing with it on a daily basis, and Shorewall certainly makes life easier. I''ve deployed Shorewall on both our Toronto and Ottawa office firewalls, and have configured a FreeS/WAN IPSEC

Hello All, Could someone please tell me if there is a was to use smbadduser in a non-interactive mode and just allow you to enter all of the particular user information on the command line? I need to set up a small script that will automate adding users to the smbpasswd file so that they can login. Cheers, Lonnie -- Lonnie Cumberland OutStep Technologies Incorporated EMAIL:

I am have a shorewall firewall and freeswan ipsec running on a redhat 8.0 Linux gateway machine. I have one working tunnel defined, all works well. I am not clear how to define mutiple concurrent tunnels. I can not add further interface entries as all the tunnels come in on ipsec0, do I still have mutiple zone definitions? some of the tunnels will be dynamic roadwarriors and as such would need a

Hello All, I hope that you are all doing well. I have been trying to get Samba setup and running on my Redhat 7.2 box so that users on Windows machines can login and be connected to their directory. The problem is that no matter what I try, I can see the Samba server from the Windows machine, but it keeps telling me that the password was not recognized and is the same linux password for each

Hello All, I am new to using wine on my Linux redhat 7.2 so please forgive the dumb questions, ok. I have been able to run a few of my Windows Applications from wine as a test, but ran into problems when I wanted to try a test and install OpenOffice 641c. I am getting messages like: ---------------------------------------------------------------- bash-2.05$ wine c:\\install\\setup Warning:

Hello All, Well my Samba server is up and running good, but I am now needing to be able to let some of my users connect to our server who is not located on our local network. Actually they are located some distance away and I would like to be able to allow then to connect. Has anyone had any success with this and how it might be done? Best Regards, Lonnie -- Lonnie Cumberland OutStep

>From your post on Oct. 4, 2004 >As I announced earlier, I''m on vacation this week and we are spending >the week at our second home. Before I left, I simulated an IPSEC tunnel >between this house and our home in the Seattle area and I''m pleased to >announce that the real tunnel works flawlessly. > >So I believe that I have done all of the testing that I can

Hello, is it possible to run tinc behind an unknown firewall(simple NAT) e.g. on windows clients to join an tinc network? These firewalls are not maintained by me and not possible to modify. Thanks for help Kai Tinc: Discussion list about the tinc VPN daemon Archive: http://mail.nl.linux.org/lists/ Tinc site: http://tinc.nl.linux.org/

Is this even a possibility? Both my brother and I have PPC G3 Mac's that we would like to install Linux on. I have downloaded a couple of Debian ISOs and a couple of Gentoo ISOs. All four would easily fit on a single CD. So, my question/problem is, is it possible to configure a menu to chose between them, that will boot up on a Mac PPC? Thanks, Lonnie -- Later, Lonnie Mostly Debian,

Hello All, I have just been reading the docs on Wine and came across the --managed Allow the window manager to manage created windows --winver Version to imitate (win95,nt40,win31,nt2k,win98,nt351,win30,win20) Does the "--managed" allow my xserver to take care of the windows? Also, if I set "--winver nt2k" then does this mean that Wine will look for the