similar to: pretty strange installation target directory?

On Mon, Jan 12, 2004 at 02:11:38PM +0100, Ralf Petry wrote: > more or less just a general question: i am running a suse linux 8.1 as > a server and ipcop 1.2 (and at another place ipcop 1.4) as > firewall/router. > i would like to achieve the following: allow a certain company (with > windows server and clients) to connect > to my network via vpn. where would i set up tinc? on

Hi, I have been working with tinc network where one host will provide the IP addresses over DHCP to each connected node. Tinc runs in switch mode. It seems that the HWaddr of the tinc interface is regenerated every time when tinc is (re)started. As a result, DHCP server will assign a new IP for the host. Is there any configuration variable we could use to avoid HWaddr changing? Currently, I

Hi, I installed tinc as described in the documentation and started the tincd. It runs, all config files seem ok, but when I do a netstat -an, it isn't listening nor connected (to another tincd on another host). Is there a configfile error or something else? Getting the right info wasn't easy either. The info on the homepage seems old, since the manpages say other configuration issue.

I'm been experiencing a very very odd problem for the past several weeks and am throwing it out in case someone can shed some light on it for me. There is a single box on our tinc mesh which can be pinged from all hosts, but cannot ping any. It is not limited to ping, the box cannot communicate over tinc. tinc is running in router mode for this mesh. ~30 other nodes function normally,

Hi Tinc group, I have recently got an adsl connection at home, which only provides a single static ip address. I want to set up a tinc vpn from home to my workplace. I am trying to decide what hardware I need to do the above. At the moment, I am aware that I could use an Alcatel Speedtouch USB modem directly connected to a Linux vpn box at my home. ( Wall socket---adsl cable---Speedtouch---usb

Hello, I'm trying to connect some windows machines together using tinc 1.0.6. The basic connectivity (ping) works fine as expected. But I'm getting really poor speeds over the tinc tunnel. The test machines are on the same switch and get values ranging from 6-9 MBytes/s speaking directly to each other. However over the tinc tunnel the speeds are in the range of 20-40 kbytes/s. The machines

hello, we use tinc for some permanent vpn tunnels with both sides are dynamic. in the last days we got following log entries on both ends: Receiving packet failed: Resource temporarily unavailable Receiving packet failed: Resource temporarily unavailable Receiving packet failed: Resource temporarily unavailable Receiving packet failed: Resource temporarily unavailable Rereading configuration

Hi, I have already working set of tinc nodes and tried to add one more machine, mac mini with osx yosemite onboard. Tincd starts and connects to other nodes as supposed but I can't connect to mini from any of other nodes. When I try to use ssh the following lines appears repeatedly in mini's logs along with the regular logs about making connections and MTU probes: > Got PACKET from

Hello, we currently set up a large tinc network with 2 central Nodes (these nodes connecting to each other). All satellites (ca 40) connect to these both machines. All containing two ConntectTo fields (for backup) e.g. (satellite) Name = nfp_hy Device = /dev/tun PrivateKeyFile = /etc/tinc/nfp_hy/rsa_key.priv ConnectTo = nfp_f_vpn ConnectTo = nfp_c_vpn If the count of satellites reaches

When I try to install the tinc RPM I am missing [root@relay buytaert]# rpm -vih tinc-1.0pre2-1.i386.rpm error: failed dependencies: libgmp.so.2 is needed by tinc-1.0pre2-1 [root@relay buytaert]# ls /usr/lib/libgmp.so.3 /usr/lib/libgmp.so.3 [root@relay buytaert]# rpm -qf /usr/lib/libgmp.so.3 gmp-3.1.1-3 This seems to be a too recent version. So I tried compiling it and got the following

hi I don't have experience at all with networks but I was triyng to install and configure tinc as a platform for multiplayer games that need to be run on a LAN. The computers run with Windows XP so I followed the example posted in the website for installation in windows. Everything is pretty clear and step-by-step, but when trying to generate the keys I get the following message: Cannot open

Hello, At FOSDEM 2010 (http://fosdem.org/2010/), I will give a lightning talk titled "tinc: the difficulties of a peer-to-peer VPN on the hostile Internet". The talk will probably be on Saturday 7th of Februari at 15:20 CET, but this might still change. If you would like to meet at FOSDEM with me or other persons using or developing tinc, just reply to this email. The abstract of the

Hello, At FOSDEM 2010 (http://fosdem.org/2010/), I will give a lightning talk titled "tinc: the difficulties of a peer-to-peer VPN on the hostile Internet". The talk will probably be on Saturday 7th of Februari at 15:20 CET, but this might still change. If you would like to meet at FOSDEM with me or other persons using or developing tinc, just reply to this email. The abstract of the

Hi everyone again. I run tinc with the following command: /usr/sbin/tincd -d1 --logfile=/var/log/tinc.log That creates the file "/var/log/tinc.log" correctly and reports into it. Well, because I want to have a log file by day, I have created a logrotate file (/etc/logrotate.d/tinc) that contains the following lines: ----------------------------------------- /var/log/tinc.log {

Hi! When I try to use tinc I get this message 'Cannot route packet: unknown type 0' when I try to ping or ssh to the box I'm connected to. Below is my setup: ifconfig tun device: -------------------- midkemia Link encap:Ethernet HWaddr FE:FD:00:00:00:00 inet addr:192.168.6.1 Bcast:192.168.6.255 Mask:255.255.0.0 UP BROADCAST RUNNING NOARP MULTICAST MTU:1500

Hello, I've just compiled tinc on OS X and have the following questions when following the instructions in the manual on the web. My environment is as follows: OS X 10.5.6 Fink 0.9.0 (Binary Package) I'm using TunTap 20080804 from http://tuntaposx.sourceforge.net/ 1. dlcompat is not found in fink. It seemed to compile ok without it, is this critical? I saw no mention of it in the

Hello, I successfully built a vpn between two hosts ("main" and "iquique") (and its SubNets), but I have problems when I want to add another host ("valparaiso"): I get a lot of Duplicates packets everywhere and a very slow vpn. I guess that is a routing problem, but I have try with a lot of alternatives without result. I have try with "switch",

Hello, I successfully use tinc for one year in a configuration with several subnets (about 5-7 subnets) and one main server. Sometimes tinc dies with the error message: Error while waiting for input: Bad file descriptor If it happens, this happens immediately, when one subnet has disconnected. tinc (on the main server) tries then to disconnect all currently connected subnets and while

Hi Who concern, I setup TINC VPN follow these. 192.168.1.x / 24 (Client groups) | 192.168.1.1 (eth1) (GW1) 202.44.34.206 (eth0) || Internet || 202.44.45.14 (eth0) (GW2) 192.168.2.1 (eth1)

Dear tinc stuff I tried to install the tinc. In the Fist Step, I install the OpenSSL-0.9.7b. 1, Go to OpenSSL-0.9.7 directory 2, ./Configure 3, make 4, make test 5, make install 2nd step, Install the tinc-1.0.1 Type "./configre" in the /usr/src/tinc-1.0.1/. Consle showed "checking EVP_EncryptInit_ex... no" and configure error. Error Message: configure: