similar to: Routing between two tunnels

Hello folks! I have a little problem when I'm trying to set up a small VPN between two hosts. The problem is that when I try to sepcify an IP-adress in /etc/tinc/netname/hosts/hostfile using Adress = xxx.xxx.xxx.xxx syslog says; Invalid variable name on line 2 while reading config file /etc/tinc/boppen/hosts/melc (Line 2 is the Adress = xxx.xxx.xxx.xxx line, and melc is the host I'm

Hello again :) Thank you all for your reply's. Below are the config files of the 3 hosts. I use  tinc in router mode. I do not have a kernel mode config lines anywhere so tinc must be using the default settings here. I added the ipaddressx to subnets on hostc and this works. Traffic to that ip is now routed via hostc. But since this ipaddressx address changes often I need to resolve it

Guus, or anyone that will help ... Okay.. I've been running tinc for a few months now, and Its been working pretty well with my machine. Attempts to install it on others WinXP Pro, WinXP Home, and WinNT boxes have been spotty at best, with some installations working perfectly, and some not working at all. My latest issue is this. My windows 2000 machine can connect perfectly to our external

On 11 April 2018 at 11:30, Hans de Groot <hansg at dandy.nl> wrote: > Hello again :) > > Thank you all for your reply's. Below are the config files of the 3 hosts. > I use tinc in router mode. I do not have a kernel mode config lines > anywhere so tinc must be using the default settings here. > > I added the ipaddressx to subnets on hostc and this works. Traffic

Hello, I'm having some routing issue with my tinc setup. I'm running a fairly basic VPN configuration between two networks: ------- Site A: ------- --- tinc-up --- #!/bin/sh /sbin/ifconfig tap0 hs ether fe:fd:00:00:00:00 /sbin/ifconfig tap0 10.11.1.2 netmask 255.0.0.0 /sbin/ifconfig tap0 -arp ---- tinc.conf --- Name = orca Hostnames = no InterfaceIP = 63.108.71.7 KeyExpire =

Dear Tinc developer, I have some problems connecting to the other site of the VPN Here are my configuration files on pc1 Configuration files on pc2 /usr/local/etc/tinc/tinc.conf /usr/local/etc/tinc/tinc.conf Name = pc1 Name = pc2 TapDevice = /dev/tap0 TapDevice = /dev/tap0 PrivateKeyFile =

Hi, I?m fighting with a silly problem: my syslog tells me tinc cannot route a packet. I can use a telnet or the good ol ping, it is the same effect. When I?m pinging from the laptop (172.16.11.2) the network address (172.16.11.0) or any address numerically lower than the laptops address, the packet gets routed, otherwise not. And when I ping the network address, I get the reply twice, as to be

Beste tinc-developer, Ik moet van mijn baas een aantal VPN's aanleggen en ben nu thuis bezig om te testen. Ik heb 2 computers in een thuisnetwerkje (totaal 6 computers) geinstalleerd met SuSe 7.3, daar de klanten dit ook hebben. De computers zijn verbonden met een switch. Dit is de inhoud van mijn bestanden: Op computer 1 genaamd suse met ip 192.168.0.99 netmask 255.255.255.0

Hi Ivo and Guus, We are writing a book on building VPNs for Linux and a part of it describes tinc. I wanted to make sure that your opinion, as tinc authors and developers, is reflected. First, let me ask a couple of technical questions. 1. If there are two hosts, foo and bar, that are to be connected via tinc, and each host should only have _one_ IP address (i.e. nmask is /32), would the

El 12 de febrero de 2016 16:51:59 CET, Eric Yau <ericyaukhy at hotmail.com> escribi?: >Hi All, > > > >I am trying to setup the site-to-site VPN with TINC for connect my home >network to company network. Here is the IP allocation and configuration >for >your reference. > > > >Home PC (192.168.1.2) ?-----? Home (OPENWRT Router, 192.168.1.1, >10.0.0.1)

Hi, I've been struggling for almost a week now, but I can't get the following setup to work. At home I have class A network: 10.0.0.0/16 with a masquerading gateway 10.0.0.1 running tinc. At work (http://www.eastsite.nl) we have a 192.168.0.0/24 network. The gateway is called 'ed' I've set up tinc on 'gateway' and everything is working fine from

I have been having some problems setting up tinc on 2 masquerading linux slackware boxes. routerA is a NAT router to the internet, for two networks on two interfaces. This are the two networks: eth1 Link encap:Ethernet HWaddr 00:E0:4C:6C:6D:86 inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX

"PrivateKeyFile" as this is default, otherwise configuration is quite minimal. ======= Configuration ========= Server Side =========== # cat tinc.conf Name = fsvpns3f30 Mode = switch Device = /dev/net/tun AddressFamily = ipv4 PingInterval = 30 PrivateKeyFile = /etc/tinc/fsvpn/rsa_key.priv # cat tinc-up #!/bin/sh ifconfig $INTERFACE 10.10.100.30 netmask 255.255.0.0 # cat

Hi Who concern, I setup TINC VPN follow these. 192.168.1.x / 24 (Client groups) | 192.168.1.1 (eth1) (GW1) 202.44.34.206 (eth0) || Internet || 202.44.45.14 (eth0) (GW2) 192.168.2.1 (eth1)

Hi all, I have been using tinc successfully for a while now. However, I need to do something different from my normal setup, and i am getting the feeling I am doing something obvious wrong. What I want to do is hookup 5 distant linux routers into one bigger network, Since I need to transmit both unicast and multicast traffic, the VPN network has to be in "Mode = switch" [Assumption

Hello, I am experiencing some weird problems in a setup with tinc where communication between the 'server' and the 'clients' occur over 3g connections. Let me describe briefly the setup: - The server, on a public IP, runs tinc 1.0.8, in router mode, and the whole setup uses one VPN network. All client's VPN addresses are on the same subnet, and each client has a seperate

Hi folks. At the moment I'm using tinc to connect to linux boxes, both of which are behind NAT. This works just fine. I'd now like to connect some roaming windows users to the network so they can browse a samba share like I can already do with linux. These folk will likely have dynamic IP addresses. The server has an IP of 10.0.0.2 My client has an IP of 192.168.1.100 Here's what

I'm really trying to do a client to server connection more than an ethernet bridge, but I couldn't figure out from the docs where that comes in. Client is Kubuntu Breezy, and server is Debian Sarge. Tinc was installed with apt-get on both systems. Version on server is 1.0.3, on client is 1.0.4. I've spent the entire day toiling over getting this set up. I had ipchains rules, etc,

Hello, response time: how is it possible to increase the response time on Tinc VPNs. When I use tinc over a fast or giga-bit network connection the ping-response time is normally about 1800 to 2000 ms. Sometimes I get ping response times at about 2.500 to 3.000 ms over a normal Ethernet Connection or a television-cable connection within the same providers-network in the same city. The ping-time

Hi I've compiled Tinc 1.0.2 from source but I'm having trouble. Not only am I having disconnections all the time (could be a network issue however) but even worse, Tinc is ignoring my MaxTimeout = 60 and is waiting longer and longer and longer (logfile shows it at 120 seconds). Is this a bug or have i misconfigured anything? best regards Marco Amrein Dec 5 11:25:12 frank