similar to: Some problems encountered by a tinc user

Hello everybody, I have just released tinc 1.0pre4. Changes: - New authentication protocol (better security, and faster too). - TCPonly and IndirectData are back (but not fully tested). - Documentation revised, it's really up to date with the released package now. - tincd -K now stores public/private keys in PEM format, but keys of 1.0pre3 can still be used. - Faster and more secure

Hello again :) Thank you all for your reply's. Below are the config files of the 3 hosts. I use  tinc in router mode. I do not have a kernel mode config lines anywhere so tinc must be using the default settings here. I added the ipaddressx to subnets on hostc and this works. Traffic to that ip is now routed via hostc. But since this ipaddressx address changes often I need to resolve it

Well this has had me stumped for days now. For months I've been using tinc in TCPOnly because I always received the unknown host error when using UDP. On Monday, i set the flag IndirectData = yes in my host files, and removed the TCPOnly line. Initially, everything worked great. My throughput increased from 600KB/sec to 2MB/sec between the sites. However, I also did some testing with

Hi, here's a small list of things that need to be done, and the version when it should be ready. smartcard support 1.1 LDAP support 1.1 public/private keys for authentication 1.1 don't store passphrases in files that are called after IP addresses 1.0 use names to identify

On 11 April 2018 at 11:30, Hans de Groot <hansg at dandy.nl> wrote: > Hello again :) > > Thank you all for your reply's. Below are the config files of the 3 hosts. > I use tinc in router mode. I do not have a kernel mode config lines > anywhere so tinc must be using the default settings here. > > I added the ipaddressx to subnets on hostc and this works. Traffic

On Thu, Mar 08, 2001 at 11:51:53AM +0100, Marcel Loesberg wrote: > I'm going to build a VPN and I want to use either Tinc or FreeS/WAN. > I've started building the VPN with FreeS/WAN and I find things are getting > rather complicated. > I looks like Tinc is much easier to configure but in the FAQ and in what I've > seen of the documentation so far there is no mention of

Hi, There are several issues with tinc that need to be fixed: - IndirectData: currect protocol "masquerades" hosts which have IndirectData set. This is bad, because you can't do loop detection anymore, and it requires a lot of dirty code to do the masquerading properly. - Loop detection: request handlers must be revised to break the right connections upon detecting a loop. -

On Mon, Nov 13, 2000 at 03:19:16PM -0500, Steve Horne wrote: > First, please forgive me if the answer to my question is accessible somewhere That's all right. > I want to set up a vpn between a computer with a standard IP address (HOME), > and one hidden behind a firewall, without an externally accessible IP address > (WORK). I can reach HOME from WORK via TCP/IP but not the

Hi, I have been messing arroudn with tinc for a while and now I got a configuration working like the example (4.7) from the manual I have 3 systems, in my case system a is the only one that can be accessed directly. B and C connect to A I have 3 subnets A 5.1.0.0 gw 5.1.0.1 B 5.2.0.0 gw 5.2.0.1 C 5.3.0.0 gw 5.3.0.1 This work fine and the gateways are ip number son t he interfaces of the 3

Hi, I´m using Tinc for several years, but I didn´t fix a performance problem. There a about 20 nodes in this network. Master: 10.0.0.12 (dedicated host in a datacenter, debian, 100mBit port) tinc.conf: Name = TincKnoten12 AddressFamily = ipv4 Interface = tun ProcessPriority=high mode = router #DirectOnly = no Compression=0 PMTUDiscovery = yes #IndirectData = yes #ReplayWindow = 64 #ConnectTo

Hello, response time: how is it possible to increase the response time on Tinc VPNs. When I use tinc over a fast or giga-bit network connection the ping-response time is normally about 1800 to 2000 ms. Sometimes I get ping response times at about 2.500 to 3.000 ms over a normal Ethernet Connection or a television-cable connection within the same providers-network in the same city. The ping-time

hi folks well, tinc is a really nice tool and we implemented it on 3 linux servers and 2 mobile clients (XP notebooks) so far. one of the 3 tinc servers is making troubles, when a connection is initiated from this server over a zyxel 642 adsl router out to the other 2 servers in the internet. the logfiles of the other 2 servers shows: > tinc[1398]: Received UDP packet from unknown

Hi I've compiled Tinc 1.0.2 from source but I'm having trouble. Not only am I having disconnections all the time (could be a network issue however) but even worse, Tinc is ignoring my MaxTimeout = 60 and is waiting longer and longer and longer (logfile shows it at 120 seconds). Is this a bug or have i misconfigured anything? best regards Marco Amrein Dec 5 11:25:12 frank

With pleasure we announce the release of tinc version 1.0.24. Here is a summary of the changes: * Various compiler hardening flags are enabled by default. * Updated support for Solaris, allowing switch mode on Solaris 11. * Configuration will now also be read from a conf.d directory. * Various updates to the documentation. * Tinc now forces glibc to reload /etc/resolv.conf after it

With pleasure we announce the release of tinc version 1.0.24. Here is a summary of the changes: * Various compiler hardening flags are enabled by default. * Updated support for Solaris, allowing switch mode on Solaris 11. * Configuration will now also be read from a conf.d directory. * Various updates to the documentation. * Tinc now forces glibc to reload /etc/resolv.conf after it

Hi, I've successfully running tinc1.0pre4 between two locations on SuSE Linux 7.1 in a special masquerading Firewall environment, so that I'm using the TCPonly keyword in the host files to get a connection. Otherwise I would get the message 'Received UDP packet on port 655 from unknown source <ipaddress in hex:port>'. After upgrading to 1.0pre5 I'm getting this message

Well i currently try to set up tinc between two hosts, one with normal dsl connection one behind some kind of unknown firewall (Note since OpenVp is able to connect when the normal one is the Server I guess tinc should be able, too) start.bat-------------------------------tincd -n Empire-Network -D -d4 --bypass-security (Bypass is only currently because tis not working yet)

Hi! Me and two friends are trying to get a VPN working, but we cant get routing between two tunnels. This is how it looks, all servers (192.168.*.1) are running IP Masquerade to enable the other computers behind them to access the internet. Both elayne and glenn are connecting to melc, and the tunnel between melc and glenn are running TCPOnly because that glenn doesnt have a public IP (it's

Hello, I'm running Dovecot2 and trying to set up public mailboxes. I've got a virtual user system set up with postfix and using MySQL authentication. I'm wanting to create several public mailboxes for shared messages. I've followed the wiki and have the public folder created. I've got a folder /home/vmail/public/public1 public1 being the maildir of the public mailbox. I can

Hello! Sorry if I am wrong with the target list but here's a picture of an issue that we have with Samba 3.0.3 and standard Windows Backup software. Actors: 1) Standard Windows Backup software that is bundled with the OS; 2) Windows 2000 SP4 Russian and Windows XP SP2 English; 3) Samba 3.0.3 running at Linux box in the Local Mode (i.e. all users are authenticated locally)