similar to: NUT MGE Pulsar Ellipse Premium 800: Changed NUT rw variables?

Hi, My UPS is MGE Pulsar Ellipse Premium 1200VA, connected on USB port, usbhid-ups driver. Using simply KNotify about UPS connection states I noticed that sometimes unpredictably a notification appears that the USB connection to the UPS is lost and a few seconds later another notification appears that the connection is restored. And this repeats to infinity. The only way to get out of it is to

I'm struggling to configuring nut for MGE Pulsar Ellipse 800 (at least Ellipse 800) for two boxes - home firewall and file server. I'm using Debian 4.0 Etch, every one of them. I'm built (after some dangerouse experiments) a testing configuration, where boxes are plugged to line, server playing as a master, firewall as a slave, and UPS connected to an electric heater about 300 Wats (no

I am running NUT 2.2.0 compiled from the FreeBSD ports tree. [inchoate 14:50] ~ >upsc ups1 at localhost battery.charge: 59 battery.charge.low: 20 battery.charge.restart: 0 battery.runtime: 6350 battery.type: PbAc battery.voltage: 43.0 driver.name: usbhid-ups driver.parameter.offdelay: 120 driver.parameter.ondelay: 13 driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version:

Hi, I have a FreeBSD 9.2 system with NUT 2.6.5 (installed via the ports tree) with an MGE Pulsar 1500 connected. A while ago it complained it needed the battery replaced and it was finally replaced last week, however I can't find out how to reset the flag in NUT. I've looked in upsc, upsrw and upscmd but none seem to have a suitable option. The UPS is connected via RS232 and upsc output

> If you set lowbatt=70 then the behaviour you are seeing is normal. Don't > set lowbatt and you'll get the default manufacturer settings which is > LOWBATTERY at 30% charge level. > > Philippe Thanks for quick response! I realized this and forget this setting! For now I think that my box does not recognize signal about low battery - I'm only started to read SHUT

Hi, I am trying to talk to an MGE Pulsar Extreme UPS over RS232 with the mge-shut driver but I'm having some problems. It appears to init OK but I can't, say, turn the outlets off, eg.. harrow:~>upsc mge@localhost battery.charge: 78 battery.charge.low: 20 battery.runtime: 05760 driver.name: mge-shut driver.parameter.port: /dev/cuad1 driver.version: 2.0.3 driver.version.internal: 0.65

Hello! We have two upses: MGE Pulsar M 3000 and MGE Pulsar EXtreme 3200C. They connect to server by USB. EXtreme works good with usbhid-ups (nut 2.2.1) and newhidups (nut 2.0.5). But Pulsar M doesn't want to work with usbhid-ups. - my ups.conf: [extreme] driver = usbhid-ups port = auto product = "EXtreme" [pulsar] driver = usbhid-ups port =

Hi, I've been using NUT for many years to look after the UPS on my home servers. Originally I was using a Compaq R3000 but that was replaced with an MGE Pulsar Evolution 3000 about a couple of years ago because the Compaq one was just too noisy! I'm just setting up a replacement server and would like to connect it using a serial cable as I've found that the USB connection

Hi, I am trying to talk to an MGE Pulsar Extreme UPS over RS232 with the mge-shut driver but I'm having some problems. It appears to init OK but I can't, say, turn the outlets off, eg.. harrow:~>upsc mge@localhost battery.charge: 78 battery.charge.low: 20 battery.runtime: 05760 driver.name: mge-shut driver.parameter.port: /dev/cuad1 driver.version: 2.0.3 driver.version.internal: 0.65

Hi all, I just bought a Trust 1000VA PW-4105 UPS. I installed the UPS on FreeBSD 6.1, and installed NUT 2.0.3 via the FreeBSD port. I had no problems installing and configuring nut and the UPS to run with the PowerMust driver. My problem however is when I test the powerdown function by issuing the command: 'upsmon -c fsd' The UPS is cutting the power before the shutdown procedure

The purpose of this posting is to summarize the FreeBSD installation procedure from the beginning till the very end. 1. Follow the instructions provided in the How-To prepared by Thierry Thomas (http://people.freebsd.org/~thierry/nut_FreeBSD_HowTo.txt). Please note the following: a) if you are using an USB device, as of NUT 2.2 usbhid-ups completely replaces the legacy hidups driver and provides

Hello, My MGE Pulsar Evolution 800 had some hardware troubles (it may be the batteries according to the manual). The fault was not detected so the power was cut to the load and nothing appears in the log files. Arnaud: do you know if the UPS have some way to report this kind of troubles to the PC so that NUT can handle it with a shutdown sequence ? Philippe

Hi all, I am trying to communicate to this Eaton Ellipse (see above) using nut from a Debian Squeeze system on Armel architecture. But have not succeeded so far. Version: Linux b3 2.6.39.4-11 #1 Tue Apr 3 21:45:12 FET 2012 armv5tel GNU/Linux Nut version is 2.4.3-1.1squeeze2 this information if from dpkg. NUT installation method:from debian package for armel. The problem is I cannot

On Jun 20, 2013, at 10:35 AM, Louis Chaillet wrote: > With respect clarification of the documentation (and reference to your question Charles). The documentation does suggest that you can shutdown the ups by the upsdrvclt shutdown [ups] command. Specifically in "http://www.networkupstools.org/docs/man/upsdrvctl.html" in the section commands under warning. In the "Network UPS

Hi Charles, thank you for your answer. This was indeed the core of the problem. I have amended the configuration files. It means now the communication works as required. Alas I now have another problem. Just for the record here is the configuration after the changes. The configuration is as follows. #nut.conf MODE=standalone #ups.conf [eaton] driver = usbhid-ups port = auto

Hello, looking for replacements for some older Powerware equipment I found the MGE Pulsar Extreme 1000C and I'm currently testing one with nut-2.0.3 on a self-brewn i386-linux. Upto now everything seems to work fine - except I can't get the power outlets switching on again after mains returns. As this works with Personal Solution-Pac 2 on W2k I thought that there might be a way to

Hello, I'm trying to communicate with a MGE Pulsar STS 16 using nut under Linux, but I've had no luck so far. I haven't saw it supported in the doc, so if there's anything I can try... Thanks, Arnaud. -- Perso: http://launay.org/blog/ H?bergement: http://www.nocworld.com/

(Sorry, I accidentally discarded the wrong message in the moderation queue - please subscribe to the list to avoid this in the future.) > From: <onyx at netfusion.fr> > Subject: [HCL] MGE Pulsar Evolution 1100 - not recognized by USB driver > Date: December 22, 2011 12:15:16 AM EST > To: <nut-upsuser at lists.alioth.debian.org> > > > Hi everybody, > > It

Hi all, Have been using Nut on Linux for over ten years now and find it brilliant. Thanks. Just upgraded to 2.4.2 and have the 5 or 6 models of UPS's that we use (apcsmart, megatec, mge-shut, surgemax, digitus) all working including the MGE Pulsar Evolution 1100 on a USB connection using the usbhid-ups driver. Running on SLES9. Old but we still have a few servers out there running

We have several systems in remote locations and I have found that the ones in the US are having issues.. We are an Australian company and can't source a 110V UPS locally so we arrange to have one bought for the site when it's installed. It seems that in the US we are getting "Pulsar EX 1500" UPSs but locally we buy "Pulsar 1500". NUT seems to work find with the