similar to: [PATCH v5 00/11] virtio: s4 support

Hi, These patches add support for S4 to virtio (pci) and all drivers. For each driver, all vqs are removed before hibernation, and then re-created after restore. Some driver-specific uninit and init work is also done in the freeze and restore functions. All the drivers in testing work fine: * virtio-blk is used for the only disk in the VM, IO works fine before and after. 'dd

Hi, These patches add support for S4 to virtio (pci) and all drivers. For each driver, all vqs are removed before hibernation, and then re-created after restore. Some driver-specific uninit and init work is also done in the freeze and restore functions. All the drivers in testing work fine: * virtio-blk is used for the only disk in the VM, IO works fine before and after. 'dd

Hi, These patches add support for S4 to virtio (pci) and all drivers. For each driver, all vqs are removed before hibernation, and then re-created after restore. Some driver-specific uninit and init work is also done in the freeze and restore functions. All the drivers in testing work fine: * virtio-blk is used for the only disk in the VM, IO works fine before and after. 'dd

Hi, These patches add support for S4 to virtio (pci) and all drivers. For each driver, all vqs are removed before hibernation, and then re-created after restore. Some driver-specific uninit and init work is also done in the freeze and restore functions. All the drivers in testing work fine: * virtio-blk is used for the only disk in the VM, IO works fine before and after. 'dd

Hi, These patches add support for S4 to virtio (pci) and all drivers. For each driver, all vqs are removed before hibernation, and then re-created after restore. Some driver-specific uninit and init work is also done in the freeze and restore functions. All the drivers in testing work fine: * virtio-blk is used for the only disk in the VM, IO works fine before and after. * virtio-console:

Hi, These patches add support for S4 to virtio (pci) and all drivers. For each driver, all vqs are removed before hibernation, and then re-created after restore. Some driver-specific uninit and init work is also done in the freeze and restore functions. All the drivers in testing work fine: * virtio-blk is used for the only disk in the VM, IO works fine before and after. * virtio-console:

Hello, These patches are an initial attempt at supporting hibernation for virtio drivers. The default configuration of event_index=on doesn't work; i.e. restore from a hibernated image only works if the devices have event_index support turned off. I have not yet dug into this, but is most likely due to some state not being sync'ed. This could be related to the hack that is patch 3.

Hello, These patches are an initial attempt at supporting hibernation for virtio drivers. The default configuration of event_index=on doesn't work; i.e. restore from a hibernated image only works if the devices have event_index support turned off. I have not yet dug into this, but is most likely due to some state not being sync'ed. This could be related to the hack that is patch 3.

Hello, Turns out S3 is not different from S4 for virtio devices: the device is assumed to be reset, so the host and guest state are to be assumed to be out of sync upon resume. We handle the S4 case with exactly the same scenario, so just point the suspend/resume routines to the freeze/restore ones. Once that is done, we also use the PM API's macro to initialise the sleep functions. A

Hello, Turns out S3 is not different from S4 for virtio devices: the device is assumed to be reset, so the host and guest state are to be assumed to be out of sync upon resume. We handle the S4 case with exactly the same scenario, so just point the suspend/resume routines to the freeze/restore ones. Once that is done, we also use the PM API's macro to initialise the sleep functions. A

This patchset replace CONFIG_PM with CONFIG_PM_SLEEP for all virtio drivers and virtio pci driver. With patch 1/2, two compile warnings are eliminated for virtio pci driver, and patch 2/2 is a clean up for all virtio drivers as suggested by Amit Shah. Aaron Lu (2): virtio_pci: pm: Use CONFIG_PM_SLEEP instead of CONFIG_PM virtio: pm: use CONFIG_PM_SLEEP instead of CONFIG_PM

This patchset replace CONFIG_PM with CONFIG_PM_SLEEP for all virtio drivers and virtio pci driver. With patch 1/2, two compile warnings are eliminated for virtio pci driver, and patch 2/2 is a clean up for all virtio drivers as suggested by Amit Shah. Aaron Lu (2): virtio_pci: pm: Use CONFIG_PM_SLEEP instead of CONFIG_PM virtio: pm: use CONFIG_PM_SLEEP instead of CONFIG_PM

Let host know of our state (partial yet) so that the host PCI device is up to where we were when we were suspended. This is still an RFC as this doesn't completely work: an unused device at the time of suspend will work fine after resume, but a device that has seen some activity doesn't behave well after resume. Especially, host->guest communication doesn't go through. This could

Let host know of our state (partial yet) so that the host PCI device is up to where we were when we were suspended. This is still an RFC as this doesn't completely work: an unused device at the time of suspend will work fine after resume, but a device that has seen some activity doesn't behave well after resume. Especially, host->guest communication doesn't go through. This could

Rusty, please review this, and consider for this merge window. This fixes the following virtio spec compliance issues: 1. on restore, drivers use device before setting ACKNOWLEDGE and DRIVER bits 2. on probe, drivers aren't prepared to handle config interrupts arriving before probe returns 3. on probe, drivers use device before DRIVER_OK it set Note that 1 is a clear violation of virtio

Rusty, please review this, and consider for this merge window. This fixes the following virtio spec compliance issues: 1. on restore, drivers use device before setting ACKNOWLEDGE and DRIVER bits 2. on probe, drivers aren't prepared to handle config interrupts arriving before probe returns 3. on probe, drivers use device before DRIVER_OK it set Note that 1 is a clear violation of virtio

Changes from v4: rename virtio_enable_vqs_early() to virtio_device_ready() Note: Rusty requested we add a BUG_ON in the virtio_ring code. This can be done by a separate patch on top. Good for bisectability in case BUG_ON starts triggering :) Rusty, please review this, and consider for this merge window. This fixes the following virtio spec compliance issues: 1. on restore, drivers use device

Changes from v4: rename virtio_enable_vqs_early() to virtio_device_ready() Note: Rusty requested we add a BUG_ON in the virtio_ring code. This can be done by a separate patch on top. Good for bisectability in case BUG_ON starts triggering :) Rusty, please review this, and consider for this merge window. This fixes the following virtio spec compliance issues: 1. on restore, drivers use device

Rusty, I have a mind to include this patchset for this merge window. Any input on this? This fixes the following virtio spec compliance issues: 1. on restore, drivers use device before setting ACKNOWLEDGE and DRIVER bits 2. on probe, drivers aren't prepared to handle config interrupts arriving before probe returns 3. on probe, drivers use device before DRIVER_OK it set Note that 1 is a

Rusty, I have a mind to include this patchset for this merge window. Any input on this? This fixes the following virtio spec compliance issues: 1. on restore, drivers use device before setting ACKNOWLEDGE and DRIVER bits 2. on probe, drivers aren't prepared to handle config interrupts arriving before probe returns 3. on probe, drivers use device before DRIVER_OK it set Note that 1 is a