similar to: Asterisk 10/1.6.1 and Dahdi/Libpri compatilities in BRI /PtmP

Hi, Until now I've been using my Digium B410P cards with misdn 1.0.x. I would like to upgrade my systems and am now wondering which is the "best" route to take: - use the latest release of misdn v1 - upgrade to the latest "stable" kernel and use the built-in misdn v2 - use misdn v2 as a seperate package (disable misdn in the kernel) - use dahdi's support for misdn

Hello, I'm reading this in my log files: [Mar 25 12:01:23] WARNING[1593] sig_pri.c: Span 1: Got SETUP with duplicate call ptr (0x8e3b998). Dropping call. [Mar 25 13:21:40] WARNING[1593] sig_pri.c: Span 1: Got SETUP with duplicate call ptr (0x8e3b998). Dropping call. [Mar 26 10:20:54] WARNING[2643] sig_pri.c: Span 1: Got SETUP with duplicate call ptr (0x8e06788). Dropping call. [Mar 26

Hi, a few month ago, I tried to install zaptel for my Beronet BN8S0 pci card... I gave up and took hfcmulti/lcr. Now dahdi (2.2.1.1) seems to support the card and I'm very interested to get it to work. But how to get rid of these annoying qozap driver? bishop dahdi # lspci -v -nn -s 01:00.0 01:00.0 ISDN controller [0204]: Cologne Chip Designs GmbH ISDN network Controller [HFC-8S]

Dear all, I know this is more a Digium hardware than an Asterisk issue. Already posted a question at Digium, however also like to see whether anyone in the Asterisk community has encountered the following situation: I installed a Digium B410P BRI PCI card on my new asterisk server, following the steps specified in the manual. I can see the PCI card is available using the lspci command: ...

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Its been a few days, I was wondering if anyone else has any ideas on how to get this to work? If not, could I ask a the direct question as to if anyone here has (or knows someone who has) successfully got something like a Cisco Router to successfully establish an ISDN data/Internet connection through the Asterisk PBX?

Hi, At the moment, libpri /w Asterisk 1.6, Dahdi 2.1, is not supporting NT-Point to multi-point mode. Here (France), most small PBXes are connected to ISDN through BRI trunks in PtmP (don't know why but it seems the general case). So this NT-PtmP function would be very helpful to easily slide an Asterisk box between an existing PBX and the network. Does the same case apply elsewhere (UK,

Hi, i use an BN4S0 with misdn an asterisk on Linux 2.6.9. The hfcmulti module is loaded with option: type=0x04 protocol=0x2,0x2,0x22,0x2 layermask=0xf,0xf,0xf,0xf and the fourth port is connected to an ISDN PTMP (MSN) port. Call to #72 from S0 (BN port 4) are not accepted from asterisk but why ? Can anyone give me a hint ?? misdn debug messages follows: lib: NEW_CR Ind with l3id:80001

Hi, I need to rebuild a system which has 4 BRI ports and is connected to Point-to-multiPoint lines, in a country where telco often "drop lines for energy savings". I'm planning to use latest 11.4.0 asterisk version along with dahdi and libpri (no misdn). Which version are recommended for Dahdi and Libpri ? My main requirements are, beside having calls coming in and out: - keep a

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Dear Supports, I was attempting to install BRI Card(OpenVox B800P) with wcb4xxp in NT mode .But I can not make it worked! Could you please give me some hints? Thanks in advance! Here are my environments: ------------------------------ CentOS-5.3 Kernel-2.6.18-164.el5 asterisk-1.6.1.6 dahdi-linux-complete-2.3.0+2.3.0 libpri-1.4.10.2 OpenVox-B800P(the first port is spliting into

Hello, I've got a running system in which logs are full of messages such as: [Jun 10 07:24:14] NOTICE[2414] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 The strange thing is those messages are coming from a single span. My setup is : Asterisk 1.6.1.18 Junghanns OctoBRI with wcb4xxp driver libpri 1.4.10.2 dahdi 2.3.0 3 BRI lines in PtMP mode What does this

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

hi i am experiencing some problems with the configuration of an BN8S0 Beronet card. I've downloaded last CVS of mISDN ans mISDNuser, i patch the kernel 2.6.16.18 and the enabled the following: <*> ISDN support x x Old ISDN4Linux ---> x x --- CAPI subsystem x x <M> CAPI2.0 support x x [*] Verbose reason code reporting (kernel size +=7K) x x [*]

Hi, I'm experiencing difficulties to get a B410P running with Asterisk 10.3.1 and DAHDI 2.6.1. Am I supposed to use DAHDI for this card and ISDN BRI for my country (Belgium)? thx, BC

Hi, As you may know, these ISDN BRI features are very important here in Europe as ISDN Basic Rate Access is very popular among Small & Medium Entreprises. I don't really know why but it seems that in many countries, default is to install small PBX using Point-to-Multipoint (PtMP) mode as opposed to Point-to-Point (PtP) which is the norm for PRI. So basically, in several countries, SME

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

Hi, I'd like to know what's the most "popular" method for automatic fax/voice detection for incoming calls on mISDN cards such as the B410P (hfcmulti). I'm running: kernel 2.6.17 misdn 1.1.3 asterisk 1.4.21.2 B410P card I'm using iaxmodem and hylafax with asterisk (the setup works for zap channels). I've used the following options in /etc/asterisk/misdn.conf:

Apart from you were dialling out on your inbound context and vice-versa. The best advice I can give now is to change to mISDN - as this is proven to work with v1.4 and v1.6. Actually - have you tried putting the 100ohm termination on for your NT port? I need to do that with mISDN as it only allows ptmp for ISDN extensions. Cheers Andy -------------- next part