similar to: Setting span orders with Astribank and Sangoma A101

Hi Guys, An 8 channel Astribank is connected to Trixbox 2.8 and I ran freepbx-module-zapauto but I get the following when running these commands and can't make calls out: [Trixbox]# dahdi_genconf xpporder /usr/sbin/dahdi_genconf: warning - OLD DRIVER: missing '/sys/bus/xpds/devices/00:0:0/timing_priority'. Fall back to /proc pbx*CLI> dahdi show channels Chan Extension Context

H all... I have an Astribank (8FXS/16FXO), IBM X3200 M2, Asterisk-1.6.2.1, dahdi-linux-complete-2.2.1, libpri-1.4.10.2, centos-5.4 final. My problem is, every time i unplug the astribank power supply, and reconnect it, astribank cannot work again (lsusb result is 11x0)... but, after reinstall the asterisk and dahdi, astribank will detected (lsusb result is 11x2)... any suggestion? Regard,

Hello, I've one astribank with 8 FXO unit and 8 pstn lines connected to the astribank. When I receive calls on my ipphone I get always Unknown callerid. It's is possible to receive the callerid from the lines on the astribank unit? This is my config: [channels] language=es context=from-zaptel signalling=fxs_ks ;rxwink=300 usecallerid=yes callerid=asreceived ;cidsignalling=bell

Hello, I recently got a problem I have never seen during my previous installations. I have a Xorcom device with 4 BRI and 8 FXS ports. I use ubuntu Linux and asterisk 1.4.22. Everything works fine but after some time zap channels disappear in asterisk. root at pbx1:~# cat /proc/zaptel/* Span 1: XBUS-00/XPD-00 "Xorcom XPD #00/00: BRI_TE" AMI/CCS NOTOPEN 1 XPP_BRI_TE/00/00/0 Clear

Hi all, After running fine for a few months now asterisk seems to hang frequently , still functioning but the DAHDI channels seem busy (users report a busy signal when calling or being called) A reboot will allow it to run for another day or maybe 2 or 3 till the problem occurs again. running stock Asterisk 1.6.2.9-2+squeeze2 on Debian with stock kernel 2.6.32-5-686 i get the following

What is dahdi.auto_assign_spans and why should you care? In later versions the kernel module dahdi[Q] includes a new parameter: auto_assign_spans. It defaults to 1, and if you set it to 0, DAHDI can start behaving in strange and completely expected ways. Chances are the default will be set to 1 in a future version. Here is why you'll want to set it yourself. Up until DAHDI 2.5, hardware

Hi, I'm having some trouble setting up a Xorcom Bri 4 port. I have compiled asterisk and zaptel using the Bristuff bristuff-0.3.0-PRE-1y-g patches. So I'm running zaptel-1.2.17.1 and asterisk-1.2.18. The problem I'm having is that for one I get no LEDs showing if the unit is in TE and NT mode (not a issue for me but may have some impact on things) I have no errors in any logs I

CC [M] /home/silentm/MessageNet/digium/zaptel-1.4.10/kernel/wcte12xp/vpmadt032.o CC [M] /home/silentm/MessageNet/digium/zaptel-1.4.10/kernel/wcte12xp/GpakApi.o CC [M] /home/silentm/MessageNet/digium/zaptel-1.4.10/kernel/wcte12xp/../voicebus.o LD [M] /home/silentm/MessageNet/digium/zaptel-1.4.10/kernel/wcte12xp/wcte12xp.o

I get the following error when trying to compile zaptel on CentOS 5 kernel 2.6.18-8.1.3.el5 CC [M] /root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.o /root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.c: In function ? /root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.c:171: error: ? has no member named ? make[3]: *** [/root/asterisk-src/zaptel-1.2.17.1/xpp/xbus-core.o] Error 1 make[2]: ***

I have a pretty large setup on one of my customers. Digium TE420B (with echo cancelling module), 3 Xorcom Astribanks with 32 FXS each and 1 Xorcom Astribank with 16 FXO. These FXO ports are NOT used for fax/data transmission, as they are connected to cell phones. Not really related to the issue, but there are also 250 SIP phones. The problem is that fax and dial-up connections are really

Hi, all My Asterisk uses a Digium TE120Pand I would like to add an Astribank zaptel_hardware sees is, but I cannot get it working pbx:~# zaptel_hardware Argument "IRQ" isn't numeric in numeric comparison (<=>) at /usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114. usb:005/002 xpp_usb- e4e4:1131 Astribank-8/16 USB-firmware pci:0000:04:00.0 wcte12xp+

I have recently updated from Centos/*1.2 to Ubuntu Server and FreePBX 2.8.0.2. We have an Astribank with 4 T1 ports and 16 FXS ports. After updating, we had it working for a while with one NT PRI and one TE PRI and, in the process of trying to configure another PRI, I ran into a couple problems. (1) As my configuration changes didn't seem to affect the Astribank, I power-cycled it. I

Hello List, it is a very long time since I wrote here.... It has been still in Zaptel times.... Today I am run into a related problem: I can't get a DAHDI setup to work 100%. I am configuring an Astribank XR00013 (BRI, two ISDN ports). At some degree the installation (latest DAHDI drivers, Asterisk 1.6.0.18 on Centos 5.x) works. I can get incoming calls to the dialplan context that is

Hi All I've got an asterisk system, using a couple of Xorcom Astribanks to provide FXS ports. (I'm using the zaptel 1.2 branch, if that matters) I've noticed that the ringing volume is a lot louder than on our old phone system, and people are starting to complain it's too loud. (This is the noise the phone makes when it rings, not the noise in your handset when you ring

Hello, I'm in the process of building an Asterisk machine and need 5 or 6 BRI-Channels. I was looking for the beroNet and Junghans cards and stumbled upon the Xorcom Astribank xBRI products. Has anybody tried out the Astribank xBRI-Channel Banks? Are they production ready or should I go with a beroNet BN8S0 or JUNGHANNS.NET octoBRI ISDN? Thanks in advance, Lars -- We don't like their

We have recently install an asterisk solution with about 60 physical extensions. While the system is running it runs reasonably well (Still have a few teething problems) but twice now they have experienced a degradation in voice quality and dropped calls and then finally asterisk completely crashes out. Restarting asterisk will work for a little while and it will crash again, each time less time

My equipement : 2x tdm 400p /4FXO/4FXS 16 PORT ASTRIBANK My first TDM400p is the sync master, so i set astribank to sync to it, but the quality is bad, like it is going fine and second after >>ROBOVOICE ;) any other devices (isdn/sip/tdm cards) are working fine, looks like astribank dont like to be sync 'slave'. Is there any way to change sync master manually, so every another

I have a server with 8 Xorcom Astribank, they're connected to the server via a USB hub, my problem is: when a reboot the server the ID of the Channel Bank changes, cousing a big mess on my server. Anybody know how can I solve this ? Best regards, -- Guilherme Loch G?es Visite nossa loja virtual: http://www.shopvoip.com.br Not?cias e F?rum sobre VoIP com software livre:

Hello Mailinglist, we have a Xorcom Astribank which is installed at our client and working since 10/2008. Suddenly last week there where odd behaviors, no calls going through (it is used to route calls to GSM Gateways). Upon testing (reinitialization of the complete gear) it turned out that one call get's through and then nothing more. I have nothing in the logs, indicating that Asterisk

Hi all, I'm interested in buy a Astribank-32 but i never heard about detection of far-end disconnection. Does anyone have some experience about that functionality in this hardware ? Thanks in Advance, Gleidson Antonio Henriques