similar to: True bond howto for Centos 6

Hi all, I've setup a ethernet bond on my centos 5.6 server , when i do a reboot the bond does come up but cleared all the slaves and i've to manually re-add them with ifenslave. does anyone know a solution to this? am i missing something? offcourse i can add it to my rc.local but there must be a more elegant way. please see my configs below Thanks, Wessel ifcfg-bond0: DEVICE=bond0

took a couple months off due to road blocks, hoping a fresh look would allow me to use my server as desired. I have three ports, eth0-2 over two nics. I want to bond them, and then use a bridge to connect to virtual machines on the virtual host computer. Never having done this, I am confused on some parts. Here is where I am at now and any pointers helpful. Single server, centos 6.x My issue

Hi all, I just noticed that my two nics that are bonded via mode 0 are showing the same mac addy in ifconfig. Is this normal? In syslog I keep getting; kernel: pbond0: received packet with own address as source address Some guidance is appreciated before I dive in and troubleshoot. If I don't list the mac addy in my ifcfg-th# files, only one of the 2 nic comes up during boot.

I'm running into a situation where a bogus bonded interface named "bond0" is being created, in addition to the desired "bond2" interface. Can anyone confirm this? Anyone know why it's happening or what I do to get rid of it? I wanted to start my numbering scheme at 2 instead of 0, which I didn't think would be a problem. As you can see, I have no reference

Hi all, we are testing CentOS 7 in order to migrate from Scientific Linux 6 / CentOS 6 and we are facing an issue with the network. Trying to configure network with teaming in activebackup mode or also with bonding in mode=1 (active backup as well) we see many RX dropped packets in the bond0 interface (around 10% of the total), 100% RX drops in the backup interface and 0% in the active interface.

Dear All, Please ignore my previous mail I have using CentOS 4.4 Linux and Kernel Version is 2.6.9-42.EL I have configured Cluster Suite with 2 servers Server 1 : 192.168.13.110 IP Address and hostname is primary Server 2 : 192.168.13.179 IP Address and hostname is secondary Floating : 192.168.13.83 IP Address (Assumed by currently active server) I have configured Ethernet Channel Bonding in

Hi! I just upgraded a machine to 7.7.1908 and the default route is not being set on boot. This particular server has a bonded interface, and the corresponding configuration for the master is ( /etc/sysconfig/network-scripts/ifcfg-bond0): TYPE=Bond BOOTPROTO=none DEFROUTE=yes IPV4_FAILURE_FATAL=yes NAME=bond0 DEVICE=bond0 ONBOOT=yes IPADDR=10.3.20.131 PREFIX=24

Hi, I'm wondering about the impact of using both dom0 and domU's on a server at the same time. I'm worried about the performance impact of running a Mysql server in a domU and now I'm thinking about moving the Mysql part of a LAMP setup into dom0 and running a few Apache guests as domUs. Since the Apaches will serve mostly from an NFS share they won't have much impact on

I have two servers with identical hardware ... TYAN i3210w system boards with dual intel gigabit interfaces, and a PCI intel gigabit nic. I'm running Centos 5.4, x86_64, 2.6.18-164.6.1.el5 Every other time I reboot, the nics initialize in a different order. anaconda had setup /etc/modprobe.conf with alias lines for the cards: alias eth0 e1000 alias eth1 e1000e alias eth2 e1000e However,

In honor of Xen Doc Day, I've put up some basic HOWTOs for setting up bridging on CentOS 6 and 7. I'm far from an expert, so I'd appreciate any feedback. The howtos can be found here: https://wiki.centos.org/HowTos/Xen/Xen4QuickStart/Xen4Networking6 https://wiki.centos.org/HowTos/Xen/Xen4QuickStart/Xen4Networking7 -George

Hi all, Someone played with kickstart bonding with centos 6.4 ? CentOS 6.4, as upstream now support ifcae bonding in kickstart network section. I've an issue with configuring a second bonding iface in kicstart on CentOS 6.4. The first bonding (bond0) works as espected but the second is not configured during installation. I've a 6 nic server (two for "puclic" network, two for

I was given the challenge recently of creating a LAN-LAN bridge between two buildings several hundred metres from each other, using only existing Cat 3 wiring and without having to resort to an expensive and finicky 5 Ghz wireless link. I was able to create a 90 megabit link for about $3,000 Cdn with new PC's, CentOS 4.1, and the newly avaliable Black Box VDSL Ethernet Extender, which

Hello all, I'm having unusual difficulty configuring teaming with Centos 4.2. The 2 NIC's are Broadcom. The HW is HP DL360 and there is no teaming driver for RHEL4 since it comes with package (says HP). Since there is no teaming driver from centos (as far as I know), I tried the Broadcom Driver, configured the team file, but the team just wont come up. A Virtual Interface should be up

Hello, I'm trying to set up IP aliases within a QEMU/KVM guest on CentOS 5.5 x86_64, going through a bridged virtualized interface. The virtualized interface in the guest is configured as follow: # ifcfg-eth1 DEVICE=eth1 BOOTPROTO=none PEERDNS=yes GATEWAY=IP.OF.HOST.GATEWAY HWADDR=11:11:11:11:11:11 IPADDR=IP.OF.GUEST.ETH1 NETMASK=255.255.255.255 ONBOOT=yes ARP=yes USERCTL=no IPV6INIT=no #

Guys, good afternoon I'm using in my bond interfaces as active backup, in theory, should assume an interface (or work) only when another interface is down. But I'm just lost packets on the interface that is not being used and is generating packet loss on bond. What can that be? Follow my settings bond [root at xxxxx ~]# ifconfig bond0 ; ifconfig eth0 ; ifconfig eth1 bond0

With the current talk on bonding, I have a few questions of my own. I'm setting up a KVM host with CentOS 6.3 x86_64 on which I'd like to attach the VMs to a bonded interface. My target setup is one where two GigE NICs are bonded and then the KVM bridge interface is attached to the bonded interface. Initially I tried to use the balance-alb mode (mode6), but had little luck (receiving

Hi, I'm trying to configure a network bridge over a bonding without any success. Here is my configuration: ifcfg-eth0: DEVICE=eth0 HWADDR=00:1E:C9:E8:3F:E5 ONBOOT=yes USERCTL=no MASTER=bond0 SLAVE=yes ifcfg-eth1: DEVICE=eth1 HWADDR=00:1E:C9:E8:3F:E7 ONBOOT=yes USERCTL=no MASTER=bond0 SLAVE=yes ifcfg-bond0: DEVICE=bond0 ONBOOT=yes BRIDGE=br0 USERCTL=no ifcfg-bridge0: DEVICE=br0

Hi, I am currently struggling with the right way to configure a bonding device via kickstart (via PXE). I am installing servers which have "eno" network interfaces. Instead of the expected bonding device with two active slaves (bonding mode is balance-alb), I get a bonding device with only one active slave and an independent, non-bonded network device. Also the bonding device

Hello everyone I am running into some strange issues when configuring networking interfaces on my physical server running Centos 7.5. Let me give you an overview of what's going on: We have a physical server, running CentOS 7.5. This server has one 4 port NIC and one 2 port NIC and a Dell IDRAC port. The first port of the 4 port NIC, em1, is used for Management traffic. The first port of

Hi, last weekend I've updated samba and ctdb on my 2-node cluster. Samba is now on 3.5.6 (from 3.3.4), ctdb on 1.0.114 (from 1.0.84). Both installed from repo via yum and ctdb-packages. After restarting both nodes everything was fine, we could access files on the cluster. On monday I noticed that the nodes didn't had their initial adresses: Node 1: hostname dscln01, public IP