similar to: battery.charge and other fixes needed for X-Power Tigra 1kVA

Dear Ladies and Gentlemen, I have several old, yet functioning APC Smart-UPS (Model 600LS, Part AP600I, Firmware 6JI, no EEPROM, from 1991). They are not supported by Powerchute any more. I run NUT 2.6.5-4 on Windows XP SP3. I use COM1 port with cable 940-0024C. The connection fails with APC Smart protocol driver 3.0 (2.6.3-3534:3540M), APC command table version 3.0 or higher - it works with APC

Hi, I have a bunch of UPSs, most connected to pcs with Linux working 100% with NUT. The only one I have a problem with, is connected to Windows 7 64bit, and I used the straight MSI installed from the website named NUT-Installer-2.6.5-4.msi Took me a while to find a way to get it to work, but it is ugly for now. Just starting up the service results in a NUT not working at all, and I tracked it

Hello all, long time away from this list, glad to be around again! I have this Powercom Vanguard VGN VGD-20K31. Some details of this model: * 3-phase input, single phase output * Model has 240V / 12V9AH x 20 x 2SET, plus another set of 20 batteries. All in all, 3 sets * Serial connection to Windows 2k3 server with UPSMon Now I was strongly considering replacing the bundled no-good upsmoon

I have only RS-232 on the box (meanwhile, it was manufactured on march of 2011) Here is my configs: nut.conf: * * MODE = netserver ups.conf: * * [KIN1500] driver = powercom port = notUsed desc = "Powercom KING PRO KIN-1500AP RM" upsd.conf: * * LISTEN 192.168.1.2 3493 upsd.users: * * [monuser] password = xxxxxxxx upsmon master

Hi, I tried using 2.6.1 version for windows with a Megatec-compatible UPS and was surprised to find out it doesn't work at all. The reason for that is blazer_ser using ser_get_buf specifying a buffer large enough to accept any reasonably possible response, setting buflen accordingly. That calls select_read() and it's supposed to wait until something is available and then to read up all

Hello. I have problem with connecting to APC SC1000 using NUT port for windows 2.6.5-6. Last working version is NUT 2.6.1-1. With the same config files it works well. c:\NUT\bin>apcsmart.exe -a SC1000 Network UPS Tools - APC Smart protocol driver 3.1 (Windows-v2.6.5-5-7-g72f380c) APC command table version 3.1 w32_serial_open (COM3) setting initial state on COM3 0000007C = w32_serial_open

Hello, I am not able to get NUT working with a APC SC1500. The ups has only a serial port and came with a 940-0272a serial to usb cable. The cable has a fake Prolific chip in it, so only works by downgrading the driver to version 3.2. I tested a 940-0024C cable without success as well. The ups works with powerchute and apcupsd with the 940-0272a cable. Have not tested it with the other one. OS:

Citeren Frederic BOHE <fbohe-guest op alioth.debian.org>: > - res = w32_serial_read(fd,buf,buflen,timeout); > + res = w32_serial_read((serial_handler_t *)fd,buf,buflen,timeout); Rather than casting away the const (which may not be possible with certain strict compiler flags), it is better to modify the prototype and definition of this function to take a 'const

Ok, so I previously thought I had to use usbhid-ups but when I eventually got it going this is what I got:- This Powercom device (0d9f/0002) is not supported by usbhid-ups. Please use the 'powercom' driver instead. So I switched to the powercom driver, but I have tried a whole bunch of likely suspects for the port setting, none of which have worked Tried so far:- com1 with these

I'm rebuilding the centosplus kernel with ISA P&P and ISA some devies enabled. At the very end of compilation, I got a lot of error messages that looked like: Error: ./init/initramfs.o .text refers to 0000046e R_386_PC32 .init.text Error: ./init/initramfs.o .text refers to 0000059c R_386_PC32 .init.text Error: ./init/initramfs.o .text refers to 000007a8 R_386_PC32