similar to: IP_MAX_MEMBERSHIPS

Hi, all! Can I enable multicasting via shorewall? I have router with Gentoo Linux (one interface to ISP, one with alises - to local network). Shorewall work perfect! But now I need setup Quagga (zebra) for dynamic routing between one more router via another provider. All routers daemons (zebra, ripd, ospf) used multicasting. In my configuration already enabled allowBcast and etc.

I am trying to set up my Shorewall box to forward multicast packets to my local net. I do have some problems with mrouted (see below), but I can join and add routes using smcroute. Multicast works when shorewall is disabled. I got a lot of help from the following. http://lists.shorewall.net/pipermail/shorewall-users/2005-January/016674.html I cannot get the multicast packets to pass the fw when

Hello, does anybody know if quagga for CentOS 5.3 is compiled with -enable-multipath? I want to implement ECMP over 2 ISP. Thanks, Cristi Carstea

Hi Everyone, I have a routing situation where Tinc looks like it could come in extremely useful, but I have a query I hope someone can cast an eye on, as I'm unsure whether Tinc can help me here. I currently have a Quagga OSPF linux router which connects LAN A to LAN B over the quickest available of two routes (both routes at both ends connect to Quagga boxes to prevent collisions). One of

The box has a fairly heavy UDP load. Its RELENG_7 as of today and took 3hrs for it to dump core. Fatal trap 12: page fault while in kernel mode cpuid = 1; apic id = 01 fault virtual address = 0x68 fault code = supervisor read, page not present instruction pointer = 0x20:0xc0637146 stack pointer = 0x28:0xe766eaac frame pointer = 0x28:0xe766eb54 code segment

Hi Laine What you have suggested sounds eminently reasonable. Thanks for your advice. I'm going to give it a shot and report back. Richard On 11/27/19 1:38 PM, Laine Stump wrote: > On 11/26/19 11:07 PM, Richard Achmatowicz wrote: >> Hello >> >> I have a problem with attaching VMs to a VLAN interface. >> >> Here is my setup: I have several physical hosts

Hello, Here is my network: ------------------ ------------- ----------- Linux box ----------- GRE --------- Cisco ---------- ------------------ ------------- What I wan to accomplish. I want ripv2 to go across (both ways) through the GRE tunnel. No packets are being passed thought the GRE

Hi folks, At work, we're considering the idea to replace the presente router with a stardard box with CentOS as a SO and GNU Zebra as a routing software. The line is a 4Mbps SDSL. ?What do you think about Zebra and what are your experiencies with it? Any feedback will be so appreciated. TIA.

Hi There, we only have a /29 internet routable network from our ISP and a Cisco 1601 router with serial interface doing all the routing. I was thinking of replacing that cisco with a linux box with a sangoma card, also using quagga with ospf on for my internel networks has anyone have expierence with this? thanks Sew

I''m getting an error when shorewall is trying to add the default routes for my multi-isp configuration. I''ve attached a shorewall dump... If anyone can give some input I''d appreciate it. RTNETLINK answers: Invalid argument ERROR: Command "ip -4 route replace default scope global table 254 nexthop via 67.110.119.245 dev eth3 weight 1 nexthop via 66.29.181.113

Hello All, Ive been doing more and more research on trying to setup a cluster/load balancer for Asterisk. All the Asterisk boxes would be using a config that is the same between them all (via a DB), but we want one location to point the phones to, and from there that machine/device will send it to a Asterisk server so the call can be processed. I know you cant balance the whole call, ie: once the

Hi list, I have a problem I thought was simple first, but now I''m stuck. In a nutshell, it''s about redundant uplinks at an outside location. Crude ASCII-Art follows: Internet | | +------------+ | cisco with | | uplinks | +------------+ | | ATM interface +----------+ ... | alvarion | | | wireless

Even more puzzling, I reverted back to the old configuration to confirm what I had seen and found that it works in one direction but not the other: i.e. from 192.168.0.110 to 192.168.0.120, but not the other way around. Must be something with my configuration....which I can follow up on. So, thanks again for your help. Richard On 12/3/19 11:36 AM, Richard Achmatowicz wrote: > Laine >

I have a standard 3 interface shorewall setup and I want to receive multicast stuff from ''net'' -> ''loc''. This requires me, first, to do an IGMP join which involves 192.168.1.x -> 224.0.0.x being NATed out as the ''net'' interface''s IP address. Obviously replies have to be NATed back to ''loc'' addresses. Can

The BBC are currently trialling multicasting the Olympics. This requires multicast and IGMP to be available. As far as I can make out, in 2.0.8 at least, all multicast addresses are filtered out and, to my naive eyes, can''t be re-enabled. Please prove me wrong :-) Dirk -- Please Note: Some Quantum Physics Theories Suggest That When the Consumer Is Not Directly Observing This Message,

http://www.open-mesh.org/ Idea #1: is BATMAN worth considering using as part of the layer 2 routing in Tinc? Idea #2: would it be possible to embed BATMAN as an option to avoid having to use Quagga for routing v6 subnets? -------------- next part -------------- An HTML attachment was scrubbed... URL:

On 31.07.2014 17:23, Dennis Jacobfeuerborn wrote: > On 31.07.2014 15:14, Dennis Jacobfeuerborn wrote: >> Hi, >> today a couple of Hypervisors got restarted due to a power outage. While >> the systems and the VMs on the are running fine multicast traffic >> between the guests is no longer working. >> >> I generate multicast udp packet using iperf in the guest

Hi Guys, I would just like to have advice and pointers of the best way would be, Someting like BGP or OSPF? I have 2 internet connections at diffrent locations. let say connection A and B 1.) router A has a fast internet connection and a seperate interface for clients using /lan/pppoe/ipsec etc and another ethernet interface going to router B 2.) router B has similiar setup as router A and

I''m just looking for a quick sanity check to make sure what I''m finding is really all necessary here. I''m upgrading a gateway/firewall from Linux 2.4 to 2.6 using Mandrake 10.1. In the old 2.4 kernel I structured my firewall rules around the ipsec0 interface, which I understand isn''t present with Openswan running under 2.6 (no KLIPS). Ok, So as I start to

From: Cong Wang <amwang at redhat.com> This is a long-standing bug and reported several times: https://bugzilla.redhat.com/show_bug.cgi?id=880035 http://marc.info/?l=linux-netdev&m=136164389416341&w=2 This bug can be observed in virt environment, when a KVM guest communicates with the host via multicast. After some time (should be 260 sec, I didn't measure), the multicast