similar to: watchdog network card

Hi I installed the following driver. http://www.f.csce.kyushu-u.ac.jp/~shigeaki//software/freebsd-nfe.html Before I had the nve driver which was unstable on this server and on a prior server in both cases causing either spontaneous reboot or just a crash when under load. So far touchwood the nfe driver has stayed up and running at almost 3 days uptime and has had some stress. I know the driver

Hi, I have a server at Hetzner and something strange happend. First, I installed FreeBSD 10.0-BETA3 (amd64) via their FreeBSD 9.2-RELEASE rescue system, that's ok. I had to configure the network by using the em driver -> em0 interface. But suddenly, the network was lost. After an ACPI reboot, nothing. Going to the vKVM show me the system didn't detected em0 anymore but an nVidia

hi, I have a hard time figuring this out, the kernel says: ... ix0: <Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 2.5.15> port 0xecc0-0xecdf mem 0xd9e80000-0xd9efffff,0xd9ff8000-0xd9ffbfff irq 40 at device 0.0 on pci4 ix0: Using MSIX interrupts with 9 vectors ix0: Ethernet address: 90:e2:ba:29:c0:54 ix0: PCI Express Bus: Speed 5.0GT/s Width x8 ix1: <Intel(R) PRO/10GbE

after trying to mount my zfs pools in single user mode I got the following message for each: May 18 09:09:36 gw kernel: ZFS: WARNING: pool 'cache1' could not be loaded as it was last accessed by another system (host: gw.bb1.matik.com.br hostid: 0xbefb4a0f). See: http://www.sun.com/msg/ZFS-8000-EY any zpool cmd returned nothing else as not existing zfs, seems the zfs info on disks

Hi, I upgraded my 7.1-RELEASE system to RELENG_7 yesterday and after booting, re0 works for only a short time, then gives "re0: PHY read failed" over and over. Does anyone have a suggestion on how to debug? Thanks, Steve

Hi list, Are there any problems with the if_re ? After upgrade RELENG_7 on my laptop NIC stopped to work:( uname -a: FreeBSD notebook.minsk.domain 7.2-PRERELEASE FreeBSD 7.2-PRERELEASE #3: Fri Apr 10 20:38:55 EEST 2009 root@notebook.minsk.domain:/usr/obj/usr/src/sys/tiger-asus-a6m i386 notebook# dhclient re0 DHCPDISCOVER on re0 to 255.255.255.255 port 67 interval 3 DHCPDISCOVER on re0 to

Hello, I need some advice how to debug this issue ... Recently I got a new mainboard for a router, it's a Gigabyte GA-H77N-WIFI with two onboard re(4) NICs. The problem is that re0 works fine and re1 doesn't: It doesn't receive any packets. Tcpdump displays all outgoing packets, but no incoming ones on re1. Ifconfig shows the link correctly (100 or 1000 Mbit, depending on where I

Dear colleagues, experimenting with new amd64-based router we found strange re(4) behaviour when working in autoselect media mode: whenever promisc mode turned on, renegotiating occurs, leading to 3 to 45 (depending on STP settings on the switch) network unavailability. Moreover, some other re(4) setting changes seem to disturb link state unneededly (such as ifconfig re0 -vlanhwtag) The most

Hello list I have a shutdown problem. I have a machine with gigabyte GA-G33M-DS2R motherboard. Integrated network card is Realtek 8111B. I can not wake the computer after I shutdown it from FreeBSD. It is a dualboot system - windows xp and freebsd. If I shutdown the computer from windows - later I can wake it up with magic packet. Even if i shutdown the machine on the boot menu with the power

I have an Asus P5Q-WS running FreeBSD 7 and the onboard Realtek NIC's are not being detected. No Kernel modifications as this is a fresh install. pciconf -lv : re0@pci0:3:0:0: class=0x020000 card=0x82c61043 chip=0x816810ec rev=0x02 hdr=0x00 vendor = 'Realtek Semiconductor' device = 'RTL8168/8111 PCI-E Gigabit Ethernet NIC' class = network

Hi, After updating from 7.0-RELEASE to STABLE (around 15/08) my NIC refuses to handle large file transfers. pciconf -lv re0@pci0:4:0:0: class=0x020000 card=0x001a6409 chip=0x816910ec rev=0x10 hdr=0x00 vendor = 'Realtek Semiconductor' device = 'RTL8110SB Single-Chip Gigabit LOM Ethernet Controller' class = network subclass = ethernet Log

I have categories and sub-categories in a table called "categories". Every row has a "parent" field to note if the entry is the sub-category of another (never goes deeper than 1 level). So there might be something like this: id | name | parent 1 Dog 0 2 Pug 1 3 Siamese 5 4 Shih Tzu 1 5 Cat 0 6 Wiener Dog 1 7 Persian

Hi all, I would like to knwon if with ZFS it''s possible to do something like that : http://tldp.org/HOWTO/LVM-HOWTO/removeadisk.html meaning : I have a zpool with 48 disks with 4 raidz2 (12 disk). Inside those 48 disk I''ve 36x 3T and 12 x 2T. Can I buy new 12x4 To disk put in the server, add in the zpool, ask zpool to migrate all data on those 12 old disk on the new and

Hi friends: I tried to convert a model object to yaml(use to_yaml method), and after that, I would like to convert the yaml(string type) back to the model object. But when I use YAML::load to do that, it failed, the return object''s class is Yaml class, not my prior model class.. Please tell me how can I do to convert yaml to an object as the prior model class, or how can I access the

Just thought I'd pass along that I have successfully installed FreeBSD 7.0 into a Xen 3.1 HVM. ?This one went as smooth as I expected, considering my experience with 6.3. ?Haven't done any benchmarking or stress testing or port installs or anything. ?But so far it's working nicely. Here's all the info. ?If you'd like to see anything else, let me know. Host hardware: ?

What does ifconfig nfe0 show for inet? -- Larry Rosenman http://www.lerctr.org/~ler Phone: +1 214-642-9640 E-Mail: larryrtx at gmail.com US Mail: 5708 Sabbia Drive, Round Rock, TX 78665-2106 ?On 7/11/18, 5:35 PM, "Teno Deuter" <gvgter at googlemail.com> wrote: but: egress_int="nfe0" you mean to put this value?

Dear All, I'm reaching this mail-list to ask a small question about disabling '3dnowprefetch' CPU feature in Xen Guest using libvirt. This is my environment: Fedora release 26 (Twenty Six) 4.11.0-0.rc3.git0.2.fc26.x86_64 xen-4.8.1-2.fc26.x86_64 libvirt-3.2.1-1.fc26.x86_64 I can disable '3dnowprefetch' CPU feature in guest via 'xl' command,

Hi all, I''m not sure if the problem is with FreeBSD or ZFS or both so I cross-post (I known it''s bad). Well I''ve server running FreeBSD 9.0 with (don''t count / on differents disks) zfs pool with 36 disk. The performance is very very good on the server. I''ve one NFS client running FreeBSD 8.3 and the performance over NFS is very good : For example

Yes, or, add another block of lines with lo (or lo0) depending on what your kernel uses for loopback in place of the $egress_int parameter to get it to listen on 127.0.0.1 as well. -- Larry Rosenman http://www.lerctr.org/~ler Phone: +1 214-642-9640 E-Mail: larryrtx at gmail.com US Mail: 5708 Sabbia Drive, Round Rock, TX 78665-2106 ?On 7/11/18, 5:38 PM,

Hi all, I have two functions called test1() and test2(). Now how do I select one of them in test3()?? Say test3<-function(func="test1"){ if (func=="test1"){ now.func<-test1() } else now.func<-test2() } I know this function I wrote does not right. Do anyone can tell me how to do that for real? Thanks a million S.H. --