similar to: GEOM_PART: integrity check failed (mirror/gm0, MBR) on FreeBSD 8.3-RELEASE

Hi, after one month with gmirror and gjournal running on a 7.0-RELEASE #p2 amd64 (built from latest CVS source), the box hung a couple of times when on high disk load. Finally, while building some port it won't boot for no reason obvious to me. This is what I get with kernel.geom.mirror.debug=2: ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire ad4: 476940MB <SAMSUNG HD501LJ

Hi. On one of my fresh installed servers I am seeing the following output during boot: gptzfsboot: error 4 lba 30 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 30 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot:

I have a GPT formatted disk where I recently expanded the size of a partition. I used "gpart resize -i 6 ada1" first to expand the partition to use the remaining free space and then growfs to modify the FFS file system to use the full partition. This was all done in single-user mode, of course, but when I enter "exit" to bring the system up, it failed to mount /usr. This was

I was using a GELI partition for /usr/home on 7.0, so it attaches and mounts on boot. The problem is it stopped working after the system was upgraded to RELENG_7/7.1-PRERELEASE. Here's how it goes: I have the following /etc/fstab: /dev/ad0s1b none swap sw 0 0 /dev/ad0s1a / ufs rw 1 1 /dev/ad0s1d

I have a new system which includes a Plextor PX-740a DVD+-R/RW CD-R/RW drive attached to an Asus A8V-MX motherboard. When I try to use burncd to burn a cd, it writes all of the data, says "fixating CD, please wait.." and then reports burncd: ioctl(CDRIOCFIXATE): Input/output error Oddly enough, the CD seems to be usable. I can successfully burn the same file if I use cdrecord. The

This used to be a single patch, but I split it into two with the addition of struct Scatterlist. Again a bit new with Rust submissions. I was told by Gary Guo to rebase on top of rust-next, but it seems *very* behind? The first patch does not build on its own due to a dead_code warning. It is hard to not have dead code when one is adding infrastructure to be used by others at a later

I have an Asus A8V-MX motherboard with an AMD Athlong 64 X2 3800+ CPU and I'm trying to run powerd to keep it cooler/quieter/greener. I'm running -STABLE (6.1-RC) cvsup'ed a couple of days ago, with a kernel config that consists of the SMP sample plus an atapicam device. I'm loading the cpufreq.ko module in /boot/loader.conf. I've attached my dmesg output and sysctl -a

I have a FreeBSD 6.2-based server running a 1.2TB graid3 volume, which consists of 5x 320gb SATA hard drives. I've been getting errors in /var/log/messages from the graid3 volume, which I suspect means an underlying fault with one of the disks, but is there any way to decipher which one of these drives is throwing errors? I've checked smartctl -a /dev/adXX but nothing shows up there..

Hello -STABLE@, So I've seen this situation seemingly randomly on a number of both physical 9.1 boxes as well as VMs for I would say 6-9 months at least. I finally have a physical box here that reproduces it consistently that I can reboot easily (ie; not a production/client server). No matter what I do: reboot shutdown -p shutdown -r This specific server will stop at "All buffers

hail, I have a soekris running an atom and 2GB RAM and ZFS using 7 drives, small capacity though, to test and study if I can make my home server this box and this way. It will be a simple server, three users tops. I followed the handbook and made the geli step on the disks: Geom name: label/zfs1.eli State: ACTIVE EncryptionAlgorithm: AES-XTS KeyLength: 128 Crypto: software UsedKey: 0 Flags: