similar to: nfe driver 6.2 stable

Hi all I've very big problem with my nfsd server. I'm running FreeBSD-stable and sometime (one time/week) i've this kind of message on the console : bge0 watchdog timeout problems fxp1 watchdog timeout problems and all my network card is down. Nothing can make the network card work again (only reboot working). There are only one service I need on this server and

Hi, tuning my network fixing nic's speed and duplex (both on server and switch) i got this error with bce driver: # ifconfig bce0 bce0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4> ether 00:15:c5:fe:11:01 inet 192.168.1.13 netmask 0xffffff00 broadcast

Hi all, Over the last month or so I've installed FreeBSD 9 (-stable) on several Mac Minis via the memstick image; they seem to be pretty good little boxes for things like offsite secondary nameservers, for example, and they're easily replaced in case of problems. However, the newest minis have slightly different hardware, and FreeBSD can't find the built-in NIC. pciconf -lv on the

Hello, recently I've installed 7.0 and now I'm observing strange thing with my Internet connection. Access to some sites may be VERY slow or doesn't work at all with different kinds of timeout messages or without messages at all (but other sites works fine). For example, firefox may say "Transferring data from..." message and then "The connection to the server was reset

Hi list, Are there any problems with the if_re ? After upgrade RELENG_7 on my laptop NIC stopped to work:( uname -a: FreeBSD notebook.minsk.domain 7.2-PRERELEASE FreeBSD 7.2-PRERELEASE #3: Fri Apr 10 20:38:55 EEST 2009 root@notebook.minsk.domain:/usr/obj/usr/src/sys/tiger-asus-a6m i386 notebook# dhclient re0 DHCPDISCOVER on re0 to 255.255.255.255 port 67 interval 3 DHCPDISCOVER on re0 to

Hi, I noticed that network connection of one of my boxes got significantly slow just after upgrading it to 8.0R. The box has an em0 (82547EI) and worked fine with 7.2R. The symptoms are: - A ping to a host on the same LAN takes 990ms RTT, it reduces gradually to around 1ms, and then it returns to around 1s. The rate was about 2ms/ping. - The response is quite slow, but no packet

1. I have a realtek network card and am using a cable modem router. Does anyone know if fixes for problems with these (see below) have been backported from HEAD to RELENG_7? 2. Is this a good time to upgrade to RELENG_7? 3. I read a post last week that advised that 7.1 is a long way off. Appreciate any advice on use of ULE 3.0 and ZFS prior to 7.1 and a comment on what is holding up 7.1. Thanks

Monitoring a tcpdump between two systems, a FreeBSD 9.1 system has the following interface: msk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=c011b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4,VLAN_HWTSO,LINKSTATE> ether 00:11:2f:2a:c7:03 inet 10.0.1.199 netmask 0xffffff00 broadcast 10.0.1.255 inet6 fe80::211:2fff:fe2a:c703%msk0 prefixlen 64 scopeid

I'm running FreeBSD 7.1-PRERELEASE over Asus P5Q motherboard. Such board comes with an nic requiring age0 driver. When the nic is under load, such trasferring big amount of data over gigabit connection (let's say some gigabyte backups), the computer hangs, sometimes with panic, sometimes freezing. Before that i was using an Intel nic with em0 driver and 7.0-Stable#2.. and that

----- Original Message ---- > From: Pyun YongHyeon <pyunyh@gmail.com> > To: Ian FREISLICH <ianf@clue.co.za> > Cc: FreeBSD Current <freebsd-current@freebsd.org>; Robert Backhaus <robbak@robbak.com> > Sent: Monday, March 17, 2008 8:12:03 AM > Subject: Re: Packet corruption in re0 > > On Fri, Feb 22, 2008 at 10:43:22AM +0200, Ian FREISLICH wrote: >

Hello, I need some advice how to debug this issue ... Recently I got a new mainboard for a router, it's a Gigabyte GA-H77N-WIFI with two onboard re(4) NICs. The problem is that re0 works fine and re1 doesn't: It doesn't receive any packets. Tcpdump displays all outgoing packets, but no incoming ones on re1. Ifconfig shows the link correctly (100 or 1000 Mbit, depending on where I

Hi, I upgraded my 7.1-RELEASE system to RELENG_7 yesterday and after booting, re0 works for only a short time, then gives "re0: PHY read failed" over and over. Does anyone have a suggestion on how to debug? Thanks, Steve

hi, I have a hard time figuring this out, the kernel says: ... ix0: <Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 2.5.15> port 0xecc0-0xecdf mem 0xd9e80000-0xd9efffff,0xd9ff8000-0xd9ffbfff irq 40 at device 0.0 on pci4 ix0: Using MSIX interrupts with 9 vectors ix0: Ethernet address: 90:e2:ba:29:c0:54 ix0: PCI Express Bus: Speed 5.0GT/s Width x8 ix1: <Intel(R) PRO/10GbE

Good morning, I'm having a bit of an issue getting a 3CR990B-TXM NIC detected and usable. Just wondering if anyone knows of any issues with this NIC chipset and/or with the motherboard chipset. The motherboard is a Biostar GeForce 6100 AM2 using an nVidia nForce 410 chipset and nVidia GeForce 6100 vide chipset. I've tried FreeBSD 6.1, 6.2, 6-STABLE (from Wed), and 7-CURRENT (from

Hello! Is anybody having stability problems with if_re under FreeBSD 6.3-stable? I know about PR kern/118719[1] but it doesn't look like the problem I'm having - at least my machine doesn't panic. My machine[2] runs FreeBSD 6.3-stable / amd64: root@kg-vm# uname -a FreeBSD kg-vm.kg4.no 6.3-STABLE FreeBSD 6.3-STABLE #1: Sun Jan 27 02:10:15 CET 2008

Hi Yonghyeon and All, >From time to time I use a notebook and boot FreeBSD from USB stick. FreeBSD 9.2-i386 works OK. So I tried to use FreeBSD 10.0-i386 BETA2 and the network adapter works for some 10-15 seconds and then stops with diagnostic message "msk0:watchdog timeout". I've found similar case at freebsd-current@ with no workaround. Yes, there is an interrupt storm as well.

Hi, I have a server at Hetzner and something strange happend. First, I installed FreeBSD 10.0-BETA3 (amd64) via their FreeBSD 9.2-RELEASE rescue system, that's ok. I had to configure the network by using the em driver -> em0 interface. But suddenly, the network was lost. After an ACPI reboot, nothing. Going to the vKVM show me the system didn't detected em0 anymore but an nVidia

I'm having problems getting PF + ALTQ to work on em(4) interfaces under 8.0-RELEASE. Kernel was rebuilt with the additional options necessary for ALTQ and what not. Same basic configuration works fine under 7.2-RELEASE. Basically, the queues create successfully but running a pfctl -vsq shows a zero packet/byte count for all queues, even the interface's root queues. This same problem is

Hello I have some problems with 3Com nics, after a upgrade from 5.5-STABLE to 6.4-STABLE. This machine has two 3com nics (one is LAN other is WAN) and i see too much "watchdog timeout" on both cards. This on/off up/down on cards, affect the interrupt to clients that are downloading from apache web server, especially on large files. --------------------------------------------

Hello list I have a shutdown problem. I have a machine with gigabyte GA-G33M-DS2R motherboard. Integrated network card is Realtek 8111B. I can not wake the computer after I shutdown it from FreeBSD. It is a dualboot system - windows xp and freebsd. If I shutdown the computer from windows - later I can wake it up with magic packet. Even if i shutdown the machine on the boot menu with the power