similar to: Can't get if_txp(4) to attach to a 3CR990B-TXM NIC

Hi, We're having some trouble with detection of a couple of Sil3124 SATA controller cards on newer motherboard and processor combos. Specifically, we're running a Supermicro X9SCM-F motherboard (latest BIOS) and Intel E3-1220v2 CPU. What we're seeing: - Syba Sil3124 PCIe cards are only being detected when installed in PCIe Slot 4 -- The motherboard documentation shows that this

Hi all, Trying to upgrade a system from 9.0-RELEASE to 9.1-PRE from yesterday on my machine (GEOM+ZFS mirror setup on ada[01]p3), the new kernel becomes unable to mount root... The only way to recover is to boot from 9.0 kernel. The disks were already named ada[01] in 9.0, so I suspect nothing there... I tried - disabling AHCI in bios (no change seen) - change cables, check PSU, test disks

Hi, there's a regression going from 6.2 to 6.3, where it will panic upon booting the kernel within vm_fault. This problem has been discussed before, but I'm seeing it reliably on a RELENG_6 checkout from 5th of May. It affects multiple (but identical) systems, here's an verbose boot leading to the panic. Please note that 6.2 was running fine on these machines, they also boot

hi folks: xorg caused my macbook 10,1 reboot immediately while startup X with latested nvidia-driver and event not to generate Xorg.0.log file attached my verbose message. thanks for any ideas --wsk -------------- next part -------------- Sep 20 15:40:31 rmbp syslogd: kernel boot file is /boot/kernel/kernel Sep 20 15:40:31 rmbp kernel: 2 Sep 20 15:40:31 rmbp kernel: MADT: Interrupt override:

Hello List, I have to dualcore Athlon 64 4800+ systems. Initially I was running 4.9 on both of them an was able to get 54mbits thru direct connected realtek 10/100 cards as measured by nttcp. I put stable on one of the system and now can on get 37mbits as measured by nttcp when going thru an ipsec tunnel. Eliminating the tunnel I get 94mbit/sec. Ideas as to why this is happening? Also

On 19 Jun 2013, at 13:34, Roger Pau Monné <roger.pau@citrix.com> wrote: > > Could you provide the boot log of the DomU, backtrace, Xen version and > Dom0 kernel version? I did not have a console attached when it rebooted, so I did not have a log of the initial boot. Now that I did, I see that it fails to mount its root volume. It had been running previously on pvhvm_v10 for about

Hello, I have a server pfsense in bridge mode to function as transparent FW, the problem is that once I connect the pfsense between my router core and my core switch catalyst a few seconds begin to appear several messages like these: em2: watchdog timeout - resetting em2: watchdog timeout - resetting em2: watchdog timeout - resetting em2: watchdog timeout - resetting And the connection falls

Hi, I have a problem, probably with the SiI 3512 SATA150 controller in a dual-Opteron IBM eServer 326: Every once a while the kernel issues a message like: ad4: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=150190687 The system waits a few seconds and continues to work normally. It typically occurs several times a day most likely depending on the load of the (SATA connected) hard drive.

Well this is new. I haven't a clue what Dell has done on this R620, but this popped up today after I did a boat load of BIOS updates and tried to install stable/9 from our yahoo tree. If anyone sees the obvious solution here, I'd love to figure it out. found-> vendor=0x14e4, dev=0x165f, revid=0x00 domain=0, bus=2, slot=0, func=1 class=02-00-00, hdrtype=0x00, mfdev=1

Hi, I had 6 crash in 3 hours with exactly the same messages is my aac controler dead ? aac0: COMMAND 0xc4c9d900 TIMEOUT AFTER 512 SECONDS aac0: WARNING! Controller is no longer running! code= 0x100 Fatal trap 12: page fault while in kernel mode cpuid = 0; apic id = 01 fault virtual address = 0x5a fault code = supervisor read, page not present instruction pointer =

One of our FreeBSD boxes has a SCSI controller and disk, which showed problems earlier this week. There was a lot of of chatter from the SCSI driver in /var/log/messages and to the console. However, the console is unattended and we only discovered the problem subsequently because /var/log/console.log didn't show any of the chatter. console.log is otherwise working, and very helpful (e.g. it

Hello Everyone, I started seeing some ata errors on a server running FreeBSD 5.4-STABLE that I've never seen before. This probably has something to do with it but we just upgraded the RAM on the server from 1 GB to 2 GB (DDR 400), perhaps a cable got slightly loose. I'm pretty certain the hard drives are good since the server ran fine prior to the memory upgrade. What do the errors below

Hi, I currently encounter spin lock 0xc0c83ba8 (sio) held by 0xc6337460 (tid 100005) too long panic: spin lock held too long cpuid=3 on hp server with two dual-core intel xeon (3.8GHz) and 3GB RAM. System is 7.1-PRELEASE last fetched 29.11.2008, 17:58 UTC. This happens with VSCom Card that was previously in use in a 5.3-STABLE system (also hp server, but older hardware) without problems. The

Here is what I did: # cd /root/nut/ # nut here it's checkouted repository # ./configure --with-user=_ups --with-group=_ups # cd drivers/ # make riello_ser # chgrp bin riello_ser # cp riello_ser /usr/local/bin # here I copied builder driver to folder where nut-package will store their files/drivers # pkg_add nut-2.6.5p1 # ls -la /dev/tty00 crw-rw---- 1 _ups _ups 8, 0 Jul 30

another attempt: # upsd Network UPS Tools upsd 2.6.5 fopen /var/db/nut/upsd.pid: No such file or directory listening on 127.0.0.1 port 3493 listening on ::1 port 3493 Can't connect to UPS [senpro] (riello_ser-senpro): No such file or directory # ls -la /var/db/nut/ total 12 drwx------ 2 _ups wheel 512 Jul 30 10:22 . drwxr-xr-x 10 root wheel 512 Jul 29 16:41 .. -rw-r--r-- 1 _ups

Hello, My server is experiencing occasional kernel panics when under moderate load. I'm attaching a crash dump and the dmesg output. I'm not sure how to read the kernel backtrace but it looks like the Intel NIC (em0) caused the problem. Occasionally, I used to get a "em0: watchdog timeout -- resetting" error message, but I never had a kernel panic. The problem started last

Can anyone help me here? ----- Forwarded message from Larry Rosenman <ler at lerctr.org> ----- Date: Sat, 9 Nov 2013 08:46:26 -0600 From: Larry Rosenman <ler at lerctr.org> To: freebsd-stable at freebsd.org Subject: 10-BETA3: Bad negotiation on AHD controller User-Agent: Mutt/1.5.22 (2013-10-16) Ever since I put 10 on this box (source upgrade from 8), I've been getting slow

These are new boxes. http://www.supermicro.com/products/system/1U/5015/SYS-5015B-MT.cfm core 2 Q6600 CPU 8Gb 667 RAM Boxes were memtested from Fri-Mon okay. 6.3-RELEASE (amd64) installs fine. Build cycle okay. Running (no load) for a week or so. However, when I try to configure gmirror they hang on boot. After some fiddling it appears issuing #kldload geom_mirror hangs the boxes very hard.

I'm trying to get stable booted on a little ITX board off of a CF card, but it hangs as it's trying to run init. Here's what the boot looks like. SMAP type=01 base=0000000000000000 len=000000000009fc00 SMAP type=01 base=000000000009fc00 len=0000000000000400 SMAP type=02 base=00000000000f0000 len=0000000000010000 SMAP type=02 base=00000000ffff0000 len=0000000000010000 SMAP type=01

Hi. On one of my fresh installed servers I am seeing the following output during boot: gptzfsboot: error 4 lba 30 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 30 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: