similar to: 1680x1050 Monitor

WoW detects my monitor hz as 77, 78, 79. 80, 81, 82 but not 60hz which it should be! This causes a lot of tearing which can be annoying. Is there any way of fixing this?

I asked on the Gentoo forums, and surprisingly haven't gotten an answer. When I run xrandr, I get this output: Code: Screen 0: minimum 2960 x 1050, current 2960 x 1050, maximum 2960 x 1050 default connected 2960x1050+0+0 0mm x 0mm 2960x1050 50.0* I'm using TwinView with a 1680x1050 monitor and a 1280x1024 monitor. And I want to set up some different modes in xrandr. When

In the vein of the "Can't get resolution higher than 1280x1024" and "Another CentOS 5 oddity..." threads, I just installed CentOS5 w/Xen kernel on a Sony VAIO desktop with an nVidia NV5M64 (RIVA TNT2 64 Pro) card, using an old Samsung SyncMaster 700NF monitor. system-config-display chose the highest possible resolution for the monitor and Xorg did its best to drive it, but

I can play WoW perfectly, it is 100% stable and I can get great fps. One problem though, when I minimize the game and I maximize it, sometimes I can just keep playing happily but sometimes thats not the case. I minimize it, maximize it again and the FPS drops to about 10-20fps (anywhere). As you might know, this is VERY annoying, I've tried changing loads of settings in-game with no help.

Hi, Did anyone manage to get 4.4 working on a Dell D620 laptop? The thing has a 1440x900 LCD screen, but I don't get X the work with that resolution. (lspci: Intel Corporation Mobile 945GM/GMS/940GML Express Integrated Graphics Controller (rev 03)) Google suggested to use '915resolution', which I installed (915resolution-0.5.2-1.el4.rf), but that doesn't help. Regards, --

Hi all! I tried to install and run Jane's USAF and Super Pro 9.4 with no luck. The game installs fine, but I cannot make it work under Linux (P-IV 2.5 + 1Gb RAM + NVidia 440Go (64Mb) with Ubuntu 9.10 + Wine 1.1.35 + NVidia 96.43.13). The game runs fine in this very same computer under Windows XP, and my computer exceeds by far the game's requirements. The original program (Jane's USAF)

I originally set up this monitor with an analogue lead. Everything seemed fine, so I didn't check xorg.conf at all. Then I bought a digital lead, and since then the monitor blinks. Running system-config-display identifies it as a 1280 x 1084 CRT monitor. It is an LCD monitor. That model is not on the drop-down list, so assuming that a specific driver wasn't available for it, I

Hi all, Up until today everything has been fine with CentOS on my Toshiba laptop. I booted into CentOS 4.3 today and Kudzu detected my video card for some reason. I let it configure it (wish I hadn't now). I can still get in. X and Gnome work. But the video resolution is 800x640. The LCD is capable of 1024x768. I cannot change it using Gnome tools or direct editing of

I have had my "nv" driver lock up a number of times. I downloaded the "nvidia" drivers and they did not work at 1920x1080 resolution. I am looking for an updated driver for just "nv". I found some once for a different driver that you just update commonXXX and yourdriverXXX not the whole X recompile. Where can I find those drivers? THanks, Jerry --------------

I just put a 1680x1050 LCD monitor on my home system, and I went into system-config-display to configure it as such, and it just won't take. I had to tweak some of the settings by hand, but when I log out, I get the wide screen for both the Nvidia driver splash screen and the login screen. But, when I log in, It jumps back to 1280x1024 and refuses to run in wide screen mode. Here's the

Ryan wrote: > I did, 1024x768. > Sorry, analog Matthew Miller wrote: > Maybe the problem is just in that adjustment, then. Yes. You need to have your signaling _exact_ when dealing with LCDs. Some are very good at taking the timings of VESA standards. But some support some eccentric Windows timings that are _not_ the exact same as VESA. Or maybe you have configured your monitor for

On 05/07/2017 11:12 PM, Ilia Mirkin wrote: > On Sun, May 7, 2017 at 7:17 AM, Sampsa Riikonen <sampsa.riikonen at iki.fi> wrote: >> Dear Devs, >> >> We have achieved a desktop of up to six monitors, with openGL running >> succesfully on the desktop, with the following setup/features: >> >> * Ubuntu 16+ >> * Xrandr >> * Noveau driver >>

First of all, I am sorry for my bad english. I have a UC-LoGIC WP8060 tablet.I using wizardpen taplet driver. I using PS 7.0 with wine-0.9.33. My Pen worked perfectly with wine-0.9.33, but PS7.0 has some bugs. I update my wine "wine-0.9.56". PS 7.0 working perfectly but my pen has not got pressure sensitive. I turn back wine-0.9.33. I have too much problems PS 7.0. I want to use new

I have a user who wants to have 4 monitors attached to his CentOS 6.4 system. I know that you can't use both on-board video and a PCI video card at the same time, but what about two PCI video cards? The system seems to recognize them as shown by the lspci -v output below, but I can't get Xorg to use the second card. Has anyone done this? If so, what is the trick to get it to work?

I've fairly recently changed my Linux desktop, and now use a XFree86 server. The default X11() window is rather small: it is supposed to be 7" x 7". However, 1) It is actually just over 5" x 5" and 2) 7" x 7" would be rather small on a 21" screen. The reason for 1) is that DisplayWidthMM give 542mm, when it is really close to 400mm (and the correct

Hello, I am having problems with video in X. I get an over frequency issue using the stock CentOS 4.2 driver. I have searched IBM and Intel for the driver but no luck. Occassionally I see something about need to load a kernel module for agpgart. How do I do this? Anyone have a similar setup or know where I can find the driver? TIA

I trying play GTA San Andreas and it is returning " Cannot find 800x600x32 video mode". I worried so my wine Games pointed for a Working Directory that register a dosdevice instead of drive_c. Thereby I'm getting" /home/normal/.wine/dosdevices/c:/Program Files/Rockstar Games/GTA San Andreas" path and "win:EnumDisplayDevicesW ((null),0,0x177f6dc,0x00000000), stub!"

hello! i am using archlinux x86_64. i have got a 32bit chroot and also 32bit libs installed, so i can run 32bit apps inside the chroot or using the libs. now my problem: my native desktop resolution is 1680x1050. i want to play my games in 800x600, 1024x768 or whatever. when i run a game in the chroot, it works like a charme, wine changes the resolution and i have no problems at all. when i run

I have an i810 chipset and am trying to set a custom mode. X is not taking that mode. Has anyone else run into this situation? How do I get X to take the mode on an i810 driver. Jerry

Hi I am trying to get Battlefield 2 and Battlefield 2142 to launch under Kubuntu 10.04 & Wine 1.3.6. I'm using an Nvidia 8800 GTX 768Mb GPU with Nvidia blob driver 260.19.12. Anyway launching BF2142 (retail copy, patched to v1.5) gives me the following error (2x) in the console output streams: Code: ... err:x11settings:X11DRV_ChangeDisplaySettingsEx No matching mode found 800x600x32