similar to: Upgrade to 4.8 STABLE - Root mount failed: 6

I have same problem on same class machine, here is dmesg from failing boot (via serial console): -------------------- Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.8-RELEASE-p7 #0: Sat Sep 20 17:07:38 EEST 2003

A problem with 4.8 reported by myself and Aaron D. Gifford. Anyone in -stable who knows more? ******** I'm assembling a Compaq 1850R with attached storage system. For the built in scsi controller (sym), there are three drives internally on channel 1 + 5 drives externally on channel 2. During boot, I can see all disks being identified first by the machine itself and then in the early part

Dear colleagues, experimenting with vinum stripes and mirrors, I'd stuck myself with the following: panic: throw_rude_remark: called without config lock (from vinumconfig.c:throw_rude_remark:103) The system before this panic has two 160G drives with two vinum partitions on each (one for mirrored root and one for the rest with swap between); these were ad0 and ad2. For the experiments,

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 This seems to be an old problem, but I haven't found much about it. SuSE mentions "hwprobe=-pci" but, as far as I know, CentOS doesn't use it. This does stop the machine from booting (mounting /) quite a few times. Logs: SCSI subsystem initialized sym0: <895> rev 0x2 at pci 0000:00:13.0 irq 177 sym0: Symbios NVRAM, ID 7,

I'm drawing a paneled histogram using the lattice package. I've succeeded in adding minor tick marks to the vertical axis, but I can't get the desired number of minor tick marks between the major tick marks. I've attached a self-contained program to illustrate the problem. Thanks for your help, Don Macnaughton Here's my sessionInfo: R version 3.4.3 (2017-11-30) Platform:

Per the Posting Guide, why didn't you post the reproducible R code example? On April 24, 2018 8:22:15 PM PDT, Donald Macnaughton <donmac at matstat.com> wrote: >I'm drawing a paneled histogram using the lattice package. I've >succeeded in >adding minor tick marks to the vertical axis, but I can't get the >desired >number of minor tick marks between the major

I have the string ggstr that I've built with string manipulation: ggstr = "ggplot(df1, aes(x,y)) + geom_smooth(se=FALSE, span=0.01)" Assuming df1 is properly defined, this string will execute properly if I submit it manually without the quotes. How can execute the command as a string, so that I can run it repeatedly (with minor modifications) in a loop? Presumably, it would be

Hi Colin, I think fcgi is only required for testing. I do without it and directly open the output files in my browser. Maybe try saying no to ramaze or whatever depends on fcgi? On Mon, Jun 1, 2009 at 18:02, Colin MacNaughton <colin.macnaughton at gmail.com> wrote: > I''m trying to install the latest webgen on Windows XP but am met with: > > [C:/Programs] gem install webgen

Thanks Jeff, I attached a file with the program to my earlier email because the posting guide seemed to imply that non-binary attachments would work. But I see that the file was stripped off. I installed the program file on a web site, but when I downloaded it, the line breaks were stripped out. So I've included the program below: ------------------------------------------------------- #

Hi, I had 6 crash in 3 hours with exactly the same messages is my aac controler dead ? aac0: COMMAND 0xc4c9d900 TIMEOUT AFTER 512 SECONDS aac0: WARNING! Controller is no longer running! code= 0x100 Fatal trap 12: page fault while in kernel mode cpuid = 0; apic id = 01 fault virtual address = 0x5a fault code = supervisor read, page not present instruction pointer =

I've just had a 4.9p1 system partially deadlock for about 30 minutes and then spontaneously(?) recover. The "ps" results point at vinum. I've never seen this before and don't recall anything like this being mentioned here before. At the time, I had two find's running in a large NFS mounted filesystem and was doing a "cvs -d /usr/ncvs -R checkout -P ports" from

I successfully did my first FreeBSD upgrade yesterday after looking at the manual, and cross referencing with Googling and getting help from our network engineer here at CWU. Before the upgrade, running df showed: Filesystem 1K-blocks Used Avail Capacity Mounted on /dev/da0s1a 507630 77662 389358 17% / devfs 1 1 0 100% /dev /dev/da0s1e

i trust i am still new in freebsd, after go through all mail and book, = now seem to be more close, i got 3 server and a notebook to play with, = install no problem. cvsup not problem.make buildworld not problem. make = build kernel become,every machine i got different error code 1,=20 1-one got system full=20 2-one showing this sometime=20 > anyone know the best way to be one time success,not

Dear Sirs. It seems to me a never ending story. We run a box with a TYAN Thunder 2500 Dual SMP mainboard, 2GB ECC Tyan certified memory, AMI Enterprise 1600 RAID adapter and additional Intel 1000/Pro server type (64 bit) GBit LAN NIC. With FreeBSD 4.8 this was stable, but to achive this state was really hard! It is a story similar to that what happend when we changed towards FreeBSD

Hi, looking at the messages i see errors with ntp everytime i reboot my server: shiva2# tail /var/log/messages Apr 5 15:32:46 shiva2 kernel: Trying to mount root from ufs:/dev/da0s1a Apr 5 15:32:46 shiva2 ntpd[385]: ntpd 4.2.0-a Tue Mar 14 04:43:54 UTC 2006 (1) Apr 5 15:32:46 shiva2 ntpd[385]: bind() fd 6, family 28, port 123, addr fe80:1::20b:cdff:fe42:3d63, in6_is_addr_multicast=0 flags=0

Greetings I'm trying to install FreeBSD on a HP Cluster Server. But when I boot with the CD's ( 4.4, 4.8 & 5.0 ), it will boot all the way upto "Wait 15 seconds for SCSI devices to settle" and then it immedialty give the following message: (noperiph:sym0:0:-1:-1):SCSI BUS reset delivered. (noperiph:sym1:0:-1:-1):SCSI BUS reset delivered. After this the machine is

Hi, I just wanted to know if anyone else is encountering error when compiling Evolution on FreeBSD 4.8 or 4.9. I have problems compiling e- util section of this port.

Hi! I'm trying to cross-compile 4.8-STABLE world to install it over NFS later. I have ./make.conf: # start of file CPUTYPE=i486 KERNCONF?=CONS MODULES_WITH_WORLD=true DESTDIR=/mnt/cons # end of file I run: dir=`pwd` make __MAKE_CONF=$dir/make.conf buildworld 2>&1 | tee $dir/bw.log It fails: ===> gnu/usr.bin/groff/contrib ===> gnu/usr.bin/groff/contrib/mm sh

Hello, I tried to install Yamaha cdrw at FreeBSD 5.1. At 4.8 stable all was Ok. Now I have in kernel configuration sym device. But cdrecord shows message "No such file or directory. Cannot open SCSI driver". Maybe I must have /dev/sym0 device or something else? If yes, then how to create it with help of devfs? There are no much info in devfs's manual. -- Oleg Shevtsov

Hi, Can someone please help me with this? I have just upgraded from 4.7 to 4.8-STABLE and this is what I am getting when I try a tape backup. Please CC as I am not in the list. It was working well before the upgrade (dump -0ua -f - / | gzip -c -9 | dd of=/dev/nsa0). Thank you, Lefteris Tsintjelis Jul 3 22:55:18 ene /kernel: