similar to: POP3 Performance

Hi, I have problems with dovecot + ldap + nfs, we could't have more than 20 concurrent sessions of pop3, when user 21 comes, the auth process takes more than 1 sec and is incresing (while most users arrives, more delay in autenticacion exists) and my customers complaint about the service. We need support about 200 concurrents pop3 users, here is my details Front Internet 1 Load Balancer

user {''username'': uid => 501, gid => ''staff'', comment => ''comment'', ensure => present, home => ''/Users/sysop'', shell =>

Thanks for Remko for his help to solve the fractional cylinder problem. But there is the second problem, the boot disk failure (see below << [B]) ... command line: initrd=disk.img harddisk c=2 h=256 s=63 BOOT_IMAGE=memdisk Disk is hard disk, 16128K CHS=2/256/63 <<<< [A] ... Loading boot sector... booting... SYSLINUX 2.04 welcome! boot: 1 [single dot]

OK, I am brand new to this so please bear with me. I have an FreeBSD 6.1 STABLE system. Postfix is installed with qpopper. The mailboxes are standard mbox format. I just installed Dovecot. At some point I want to update to a mdir format, etc., but quite frankly I do not know how to go about that. In any case, I shut down qpopper and started Dovecot. I modified the Dovecot.conf file SSL settings

Hello All, I am new to Dovecot and the Dovecot mailing list. I am trying to migrate an existing Exim + qpopper - mbox (pop3 only) installation over to Exim + Dovecot using mdir (pop3 and imap) And am running into problems with preserving the XUIDL headers. I am running Dovecot 2.0.14 I have used the mb2md.pl script : http://dovecot.org/tools/mb2md.pl from this page

hi all, "uncle"! i've thrown up my hands with cyrus, and am looking for a 'better alternative' ... i'm brand new to dovecot (haven't even built it yet ...), and have spent the last while reading through the LIST archives here. apart from the TECHNICAL aspects, which seem _more_ than adequate/competitive, i'm most attracted by a comment abt this

Yes, really. I've got hundreds of the damn things here at home, and I want to go through them and get rid of them all. But... to do that I want to read them. I have both a 5.25" and a 3.5" drive, both are plugged in, but in the BIOS, all I see is the 3.5". Fine, I figure I'll take care of those. Nope. I see /dev/fd0 once I've booted up, but neither konqueror nor

Hi, sorry if this is old stuff, but I did my best to look first... Have been getting errors along these lines: mv mydir mdir.2002 ln -s mydir.2002 mydir Then update mirror with rsync -av --delete-after. Without --delete-after, no problem, with --delete-after, get a code 23. The attached shell script will recreate the error (on my machine, at any rate). Just run it from a clean directory.

If there a way to may samba "handle" files like ftp does during ascii transfers. Changing the ^m to unix end of line markers

On the Squirrelmail website I setup in the FAQ a quick install guid on how to get squirrelmail to work with Dovecot. Maybe someone can verify my setup procedure really quick. Maybe someone thinks this is wrong. Also if you have something to add please do so. No one has bothered to do this before so I took it upon my self. Here is the link in the FAQ its about 8 lines down

Hello, I would like to convert all users mail from maildir to mdbox. My Dovecot version is 2.0.1, converted from 1.2.13 but config was rewritten from scratch. http://wiki2.dovecot.org/Migration/MailFormat says following: maildir -> mdbox migration. Set mail_location=mdbox:~/mdbox and run doveadm convert -u username maildir:~/Maildir but doveadm does not know a command like

Hi. I recently mentioned in several posts, that I'd tended to use mbox rather than maildir, because you don't loose so much space (due to always allocating full blocks per maildir file and thus per mail). I made some tests of my archive, which consists of some 3,4 million mails at a total of 42GB). Most of these mails are probably normal sized, but there are also some with bigger

Hey all, we're in the process of checking out alternatives to our index storage. We're currently storing indexes on a NetApp Metrocluster which works fine, but is very expensive. We're planning a few different setups and doing some actual performance tests on them. Does anyone know some of the IO patterns of the indexes? For instance: - mostly random reads or linear reads/writes?

Problem: Dovecot is totally and merrily oblivious to maildir INBOX installed in the usual /var/spool/mail/%u Software/system: Dovecot 1.2.8 running under Fedora 12 with 1.9 gig RAM + AMD Athlon LE-1640 CPU on a ASUS M3A78-EM motherboard (uname -a = Linux 2.6.31.6-162.fc12.x86_64 #1 SMP Fri Dec 4 00:06:26 EST 2009 x86_64 x86_64 x86_64 GNU/Linux ) Dovecot has been installed from the Fedora

Hello there. I'm try to configure squid3 with samba4-alpha-10 autentication. My samba4 pdc work fine with a simple smb.conf: [globals] netbios name = PANTRO workgroup = MYDOMAIN realm = MYDOMAIN.LAN server role = domain controller [netlogon] path = /usr/local/samba/var/locks/sysvol/mydomain.lan/scripts read only = no

Hi List, I would like to discuss with whoever is interested one topic that I suppose has general interest. I want to implement some kind of automatic testing on the status of a node after a Puppet Run. These tests involve trivial and less trivial things things like: - A local service is running - A local port is open - A remote server on a remote port is reachable by the node - An URL replies

Hi, Since I had upgraded from Samba 3.0.0 to 3.0.4 I have problems with ArcServe to connect to the share. Arcserve is running on a NT 4.0 box, everytime I try to connect to the samba share it says me "authenticacion failed". When I browse the share from windows explorer I have not problems. Thank you in advance Guillermo

hi, how to add radius support to asterisk 1.4.5? i do make menuselect and i do not see any module or option related to radius, pam, authenticacion or similar. any ideas? thanks

Jesus how do u post something, it always comes back :( -----Original Message----- From: Rend, Jon (Jon) % [mailto:rend@agere.com] Sent: Tuesday, October 29, 2002 8:05 AM To: 'samba@lists.samba.org' Subject: [Samba] (no subject) On friday we changed our smb.conf file to test the security model that uses DOMAIN authenticacion. It worked fine testing two seperate usernames from Multiple

Hola Soy Maricela Debo realizar un proyecto de autenticacion de usuarios para una red interna de una empresa, esto se realizara en linux con Samba 3.0.2 y LDAP. Estube mirando este articulo porq me recomendaron usar: sambaSamAccount y posixAccount, pero tengo dudas. Queria preguntarte si me puedes ayudar: 1. El esquema jerarquico es definir el los componentes de domino y los objectclass