similar to: Digium FXS specifications and limits Question

Howdy All, They say opinions are like belly buttons, everybody has one. (that's the "clean" version of the saying). So I'm asking for yours. I hope you see it as a fun exercise. I'm designing a phone system from the ground up. Will be about 1000-1300 seats mixed 80/20 VoIP/Analog. 58-acre campus environment with 23 buildings. Userbase is emergency services

Hi, 1. Is there any manual entry about modprobe's options relative to a given Dahdi driver (wctdm24xxp, for instance) ? 2. When loading a wctdm24xxp driver, is there any parameter to pass to modprobe to configure a span in NT/point to point mode ? 3. After running dahdi_cfg -vvvvv , I can read with dmesg : [ 1986.289277] wctdm24xxp 0000:04:06.0: xhfc: Configuring port 0 span 1 in TE mode

Dear all, I know this is more a Digium hardware than an Asterisk issue. Already posted a question at Digium, however also like to see whether anyone in the Asterisk community has encountered the following situation: I installed a Digium B410P BRI PCI card on my new asterisk server, following the steps specified in the manual. I can see the PCI card is available using the lspci command: ...

Hello I'm sure someone has already tried this: I use a couple of electric heaters to heat my office. I'd like to somehow connect them to Asterisk so that I could switch them on remotely by either calling the IVR or sending an e-mail to the Asterisk host, so that the room is warm when I get to the office :-) Any information appreciated. Thank you.

Dear R users, I am working on allocating the rows within a dataframe into some factor levels.Consider the following dataframe: Start.action Start.time 1 Start.setting 2010-12-30 17:58:00 2 Start.setting 2010-12-30 18:40:00 3 Start.setting 2010-12-31 22:39:00 4 Start.setting 2010-12-31 23:24:00 5

Does anybody know how to build a handset to sound card adapter ? Thanks! --------------------------------------- Norberto Harmath Centro de Comunicacion Cientifica Universidad de Buenos Aires

>Or, you could use a Corinex Phone Line Bridge which runs 128Mbits up to 2000 >feet. They also have a co-ax version which is 200mbits and goes 4000 feet... >About $300 for both ends. too bad they don't say what the bandwidth is at max distance - anyone know?

Hi guys, I've been experiencing a very strange issue with my Digium Card TDM400 as of this week. It has two FXS and two FXO. The FXO modules (both of them) never goes on-hook after hanging up in Asterisk. It had worked perfectly well for over four years. I put an ammeter in series with the line and the card, and immediately after plugging the connector to the card, I got 26mA in the circuit

I was given the challenge recently of creating a LAN-LAN bridge between two buildings several hundred metres from each other, using only existing Cat 3 wiring and without having to resort to an expensive and finicky 5 Ghz wireless link. I was able to create a 90 megabit link for about $3,000 Cdn with new PC's, CentOS 4.1, and the newly avaliable Black Box VDSL Ethernet Extender, which

Greetings all, After a long day of fighting with GTalk and having it finally working, I wanted to setup DPMA on my Digium phone. So first of all, I had to reinstall it all and reconfigure it all, since it works only on certified versions, and my installation was not from the certified branch. It took a long time of recompiling, testing, adding missing stuff, but I got it straight. Now, I

Hello everybody, I try to install -Ubuntu 8.04 server- a B410P and a TDM2400P together with Asterisk 1.4.26-2, dahdi-linux-2.2.0.2 and dahdi-tools-2.2.0. Problem I face is the following one: CLI> module load chan_dahdi.so == Registered application 'DAHDISendKeypadFacility' == Registered application 'ZapSendKeypadFacility' == Parsing

I'm attempting to set up a 2-way NT4-style trust between samba 3.0.1-2 (from source rpm on redhat 7.2) and Windows 2003 running active directory. The AD server (SANDMAN) trust of my Samba domain works fine, but when I try to use the Samba trust of the AD server I get the following error: [2004/02/04 15:52:34, 3] rpc_client/cli_pipe.c:rpc_api_pipe(462) Bind NACK received on pipe c009!

Looking for someone with a successful experience similar to this; I have a need to cross connect a 3COM NBX PBX PRI interface to asterisk, but over a long distance. We do not need any IP connectivity and the solution requires G.711u audio so there is no benefit to using IP. Has anyone here successfully cross connected any PBX PRI interface expecting NI2 PRI signaling B8ZS/ESF with an

I think this is the minimal recipe: winetricks ie6 winetricks ie8 wine iexplore Installing ie6 just makes the menus work, I think.

Hello! I have a sip device that is sending in the SDP: rtpmap:98 g729a It does not seem like Asterisk is negotiating the codec properly, because while the call rings, the rtp lines fail. However, on other sip devices that have "rtpmap:18 g729" in their SDP, things work fine with Digium's commercial g729 license. How do I get "98 g729a" recognized by Asterisk? Thanks,

I'm trying to use Asterisk as a PSTN simulator to run performance tests for echo cancellation algorithms. I'm using the following configuration: SIP <-----> Asterisk 1 <----> Asterisk 2 <----> Echo() Asterisk 1 and Asterisk 2 are connected using E1. Echo() is the dialplan application. The problem is the high delay using this configuration: 20 ms only in Asterisk 2.

Hi, I have been trying to get a Wildcard TE122 card running here the last couple of days. libpri and zaptel are all installed and configured to E1 specs. The jumper on the card is on, so configured for E1 (I'm in Norway). When running zttool, I get 'Alarms: RED' on the single card installed. Other information in zttool: Current alarms: Red Alarm Sync source: Internally clocked

Hi all, Do you have an idea on the best way on how to implement a system with multiple Asterisk servers with BLF working in such a way that a peer on one server can subscribe to another peer on the other server in a seamless manner? Has anyone set-up a system like this before? Thanks! Regards, Ronald -------------- next part -------------- An HTML attachment was scrubbed... URL:

Dear all, Given data of a continuous frequency distribution with class intervals .. how to enter such data so that we can use the normal mean, median and mode functions to calculate them and also can draw histogram .. for example how to enter this data in R Height range[image: ↓]<http://en.wikipedia.org/wiki/Frequency_distribution#> Number of students[image: ↓]

Dear R-ers, I am a gratuate student from South China University of Technology. I fond the function 'sprintf' in R2.10.1 have a little bug(?): When you type in the example codes: > sprintf("%s is %f feet tall\n", "Sven", 7.1) and R returns: [1] "Sven is 7.100000 feet tall\n" this is very different from the 'sprintf' function in C/C++, for in