similar to: Bug#655581: xen-utils-common: network-bridge breaks the network setup when using ethernet bonding.

Package: xen-utils-common Version: 4.4.1-5 Severity: important Dear Maintainer, I tried to upgrade xen-utils-4.4 depending on xen-utils-common. Here is aptitude answer: ... Param?trage de xen-utils-common (4.4.1-5) ... insserv: Service xenstored has to be enabled to start service xendomains insserv: Service xenconsoled has to be enabled to start service xendomains insserv: exiting now!

Package: xen-utils-common Version: 4.0.0-1 Severity: normal Hi, On system shutdown the 'xendomains' script appears to detect wrong guests: | Stopping libvirt management daemon: libvirtd. | Clearing ebtables rulesets: filter nat broute done. | Shutting down Xen domains: bev-d6x02(save).Error: Domain '1024' does not exist. | !(shut).Error: Domain '1024' does not exist. |

Apologies, there is a slight change required to the solution. replace the do_ifup line as follows: if [ -n "${slaves}" ]; then ip link set dev $bridge up [ -n "$gateway" ] && ip route add default via ${gateway} else do_ifup ${bridge} fi -- Philip Ward Unix Systems Administrator 01786 467274 (ext 7274) -- The Sunday Times

I''ve migrated my Dom0 host to Xen 4.2.0 + xl toolstack. With ''xm'' toolstack, configs in /etc/xen/auto are autostarted, assuming xend/xendomains services are started. IIUC, when using xl toolstack, those services are not to be started; and, afaict, the installation process for 4.2 has them disabled by default. Now, the configs in /etc/xen/auto are simply ignored. I

Package: xen-utils-common Version: 4.3.0-3 Severity: normal Dear Maintainer, * What led up to the situation? I upgraded my server from squeeze to wheezy and then to jessie. Server is Intel S3200SHV m/b with Intel(R) Core(TM)2 Quad CPU. I'm pretty sure that before that it was running whatever came before squeeze, I forget the name. I was trying to get xen_pciback to work, so I

Package: xen-utils-common Version: 4.1.3~rc1+hg-20120614.a9c0a89c08f2-2 Severity: important Please modify the init scripts in a manner similar to the following to give the correct SE Linux labels. Failing to correctly label them may result in Xen not working correctly when SE Linux is enabled. --- /etc/init.d/xen.orig 2012-06-24 10:29:04.000000000 +1000 +++ /etc/init.d/xen 2012-06-24

Package: xen-utils-common Version: 4.0.0-1 Severity: normal Tags: patch do_ifup() in network-bridge exits badly, if the interface doesn't have a default gateway. Since it's wrapped in xen's locking script it causes it to be retied 100 times and sleep for 95 seconds before it continues. In my setup this amounts to: 16 vlans without a default gateway * 95 secs / bridge = 25 minutes

# HG changeset patch # User Ian Campbell <ian.campbell at citrix.com> # Date 1341877305 -3600 # Node ID 310aa4c07d02168234a36e113a76d0d4eef373a7 # Parent 1d33f934dd675a1b91d2d4e0fa2d2a873a8debf5 hotplug: network-bridge: fix for interfaces with no gateway This comes from an old Debian bug report http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=588477 which refers to

Dear All, I have configured Cluster Suite with 2 servers Server 1 : 192.168.13.110 IP Address and hostname is primary Server 2 : 192.168.13.179 IP Address and hostname is secondary Floating : 192.168.13.83 IP Address (Assumed by currently active server) I have configured Ethernet Channel Bonding in Each Cluster Nodes and Channel Bonding Configuration Details are 1) Created bonding devices in

HI All. I have a linux box connected to a switch network with 2 network interfaces, how would I able to ''trunk'' these 2 interfaces? options I can see are: - ethernet bonding - iproute2? - teql Which one are the best to use? I''m curretly having problem with ethernet bonding, my setup are as follow: ip add: 192.168.10.30/24 I do: # modprobe bonding # ip addr add

Dear All, I have configured Cluster Suite with 2 servers Server 1 : 192.168.13.110 IP Address and hostname is primary Server 2 : 192.168.13.179 IP Address and hostname is secondary Floating : 192.168.13.83 IP Address (Assumed by currently active server) I have configured Ethernet Channel Bonding in Each Cluster Nodes and Channel Bonding Configuration Details are 1) Created bonding devices in

Hello, when I boot DomU which uses DHCP to configure IPv4 address it does never get a lease. The packets travel to Dom0 where the dhcp server receives them, sends a reply, that travels to DomU where dhclient receives it, says the checksum is invalid, and discards it. The problem is documented here: http://old-list-archives.xen.org/archives/html/xen-users/2006-02/msg00152.html

Dear All, Please ignore my previous mail I have using CentOS 4.4 Linux and Kernel Version is 2.6.9-42.EL I have configured Cluster Suite with 2 servers Server 1 : 192.168.13.110 IP Address and hostname is primary Server 2 : 192.168.13.179 IP Address and hostname is secondary Floating : 192.168.13.83 IP Address (Assumed by currently active server) I have configured Ethernet Channel Bonding in

Setting up bonding in active-backup mode 1 (using ARP monitoring) on a server, it looked OK, but pulling the active link cable didn't actually work, it didn't fail over. Eventually with manual playing around with modprobe, ifconfig, ifenslave, etc., a solution was stumbled upon: enslave the eth1 device before eth0, and all is good. Why this should matter is a puzzle - I could not find

Hello, in the last days I switched from Xen 4.2.1 to Xen 4.2.2 (source from git repository tag 4.2.2) commit a125ec6a4a2f028f97f0bdd8946d347a36dbe76b Author: Jan Beulich <jbeulich@suse.com> Date: Tue Apr 23 18:42:55 2013 +0200 update Xen version to 4.2.2 My "base system" is a debian squeeze. For Xen I use the xl toolstack. Since updating to 4.2.2 the autosave and

We had problem using tagged vlans inside domU. Testing shows that this is caused by changing network interfaces in network-bridge script. Following patch should allow to use vlans in guest. Testing scenario: configure vlan network (e.g. vlan 1 on eth0 => eth0.1) start xend create domU and configure same vlan inside it You can see that vlan is still <interface>.<vlan_id>. You can

Package: xen-utils-common Version: 4.3.0-3 Severity: normal Dear Maintainer, I've just set up a fresh Jessie system using the installer dated 2014-03-05, then installed and enabled Xen 4.3. I've done this quite a few times before using Wheezy and 4.1. I set up xenbr0, then created a test domU using xen-create-image, which completed without issue. However I was unable to start the new

Hello, for everybody who develops or uses the script /etc/init.d/xendomains, there is a serious error in this script. If the given variable XEN_DOMAINS_AUTO_ONLY is set to true in /etc/sysconfig/xendomains, then the saving of the domains always fails - the domains are shut down instead of the saving. This is very bad especially for some HVM domains which MUST be saved instead of shut

Hello, for everybody who develops or uses the script /etc/init.d/xendomains, there is a serious error in this script. If the given variable XEN_DOMAINS_AUTO_ONLY is set to true in /etc/sysconfig/xendomains, then the saving of the domains always fails - the domains are shut down instead of the saving. This is very bad especially for some HVM domains which MUST be saved instead of shut

Hallo, I have running xen-4.2/linux-3.8 (compiled) on any hosts. - dell pe r720: drac, eth0-3:igb squeeze -> boot_xen:ok net:ok bridge:ok - dell pe R620: drac=eth0, eth1-3:tg3 wheezy -> boot_xen:ok net:ok bridge:fail So i running "xend start" (or "xenbridges start") on my patient (R620 with broadcom tg3) network will be lost: RTNETLINK answers: File exists